DTC P0340 Camshaft Position Sensor Circuit Malfunction |
DTC P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) |
DTC P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0340 | When one of the following conditions is met:
|
|
| P0342 | The output voltage of the camshaft position sensor is below 0.3 V for 4 seconds (1 trip detection logic). |
|
| P0343 | The output voltage is higher than 4.7 V for 4 seconds (1 trip detection logic). |
|
![]() |
| ECM Terminal Name | CH1: Between VV1+ and VV1- CH2: Between EV1+ and EV1- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling |
| Required Sensors/Components (Main) | Camshaft position sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR) |
![]() |
Disconnect the camshaft position sensor for intake camshaft connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| E55-3 (VC) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Camshaft Position Sensor for Intake Camshaft) |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM) |
Disconnect the camshaft position sensor for intake camshaft connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E55-1 (VVI+) - E26-82 (VV1+) | Always | Below 1 Ω |
| E55-2 (VVI-) - E26-114 (VV1-) | Always | Below 1 Ω |
| E55-1 (VVI+) or E26-82 (VV1+) - Body ground | Always | 10 kΩ or higher |
| E55-2 (VVI-) or E26-114 (VV1-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT) |
![]() |
Check the camshaft position sensor for intake camshaft installation.
|
| ||||
| OK | |
| 4.INSPECT INTAKE CAMSHAFT (TIMING ROTOR) |
Check the timing rotor of the intake camshaft.
|
| ||||
| OK | |
| 5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) |

| *1 | Timing Mark | - | - |
Remove the cylinder head cover sub-assembly.
Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.
Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.
|
| ||||
| OK | |
| 6.REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT) |
Replace the camshaft position sensor (for intake camshaft) (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342 OR P0343) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Turn the tester on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0340, P0342 or P0343 is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM) |
Disconnect the camshaft position sensor for intake camshaft connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E55-3 (VC) - E26-113 (VCV1) | Always | Below 1 Ω |
| E55-3 (VC) or E26-113 (VCV1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||