DTC C1426 Stop Light Switch OFF Stuck Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| C1426 | Either of the following is detected:
|
|
| 1.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION |
Check the brake pedal height and stop light switch assembly installation (Click here for LHD or Click here for RHD).
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK STOP LIGHT OPERATION |
Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
| Condition | Illumination Condition |
| Brake pedal depressed. | ON |
| Brake pedal released. | OFF |
|
| ||||
| OK | |
| 3.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Select the Data List using the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Stop Light SW | Stop light switch / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
Check that the stop light switch display observed on the intelligent tester changes according to brake pedal operation.
|
| ||||
| OK | |
| 4.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1426 is not output. | A |
| DTC C1426 is output. | B |
|
| ||||
| A | ||
| ||
| 5.INSPECT STOP LIGHT SWITCH ASSEMBLY |
Check the stop light switch assembly (Click here for TMC, TMMR made or Click here for TMMK made).
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (STP TERMINAL) |
![]() |
Reconnect the stop light switch assembly connector.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-30 (STP) - Body ground | Stop light switch ON (Brake pedal depressed) | 11 to 14 V* |
| A49-30 (STP) - Body ground | Stop light switch OFF (Brake pedal released) | Below 1.5 V |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly)) |
|
| ||||
| OK | |
| 7.RECONFIRM DTC |
Reconnect the skid control ECU connector.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC C1426 is not output. | A |
| DTC C1426 is output. | B |
|
| ||||
| A | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (STP TERMINAL) |
![]() |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-30 (STP) - Body ground | Stop light switch ON (Brake pedal depressed) | 11 to 14 V* |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly)) |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-38 (GND1) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly)) |
|
| ||||
| OK | ||
| ||