FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) > One or more Power Seat Motors do not Operate |


| 1.CHECK FRONT POWER SEAT OPERATION |
Check that each function of the power seat operates normally by using the power seat switch (Click here).
| Result | Proceed to |
| One or more power seat functions (except lumbar support adjustment function) do not operate | A |
| All power seat functions do not operate | B |
| Front vertical and lifter functions do not operate | C |
| Only lumbar support adjustment function does not operate | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING GTS (POWER SEAT SWITCH) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body / Driver Seat / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Reclining Rear | Reclining switch signal (Rearward) / ON or OFF | ON: Reclining switch (Rearward) on OFF: Reclining switch (Rearward) off | - |
| Reclining Front | Reclining switch signal (Forward) / ON or OFF | ON: Reclining switch (Forward) on OFF: Reclining switch (Forward) off | - |
| Front Vertical Down | Front vertical switch signal (Downward) / ON or OFF | ON: Front vertical switch (Downward) on OFF: Front vertical switch (Downward) off | - |
| Front Vertical Up | Front vertical switch signal (Upward) / ON or OFF | ON: Front vertical switch (Upward) on OFF: Front vertical switch (Upward) off | - |
| Lifter Switch Down | Lifter switch signal (Downward) / ON or OFF | ON: Lifter switch (Downward) on OFF: Lifter switch (Downward) off | - |
| Lifter Switch Up | Lifter switch signal (Upward) / ON or OFF | ON: Lifter switch (Upward) on OFF: Lifter switch (Upward) off | - |
| Slide Rear | Slide switch signal (Rearward) / ON or OFF | ON: Slide switch (Rearward) on OFF: Slide switch (Rearward) off | - |
| Slide Front | Slide switch signal (Forward) / ON or OFF | ON: Slide switch (Forward) on OFF: Slide switch (Forward) off | - |
|
| ||||
| A | |
| 3.PERFORM ACTIVE TEST USING GTS (POWER SEAT MOTOR) |
Enter the following menus: Body / Driver Seat / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Seat Reclining | Seat reclining operation | OFF/Rear/Front | - |
| Front Vertical Operation | Seat front vertical operation | OFF/Down/Up | - |
| Lifter Operation | Seat lifter operation | OFF/Down/Up | - |
| Seat Slide Operation | Seat slide operation | OFF/Rear/Front | - |
| Result | Proceed to |
| The power seat functions operate normally. | A |
| Slide, front vertical or lifter function does not operate normally. | B |
| Reclining function does not operate normally. | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 4.INSPECT SEPARATE TYPE FRONT SEAT CUSHION ASSEMBLY |
![]() |
Disconnect the e8, e9 or e10 connector from each motor.
Check the operation of the slide motor.
Check if the seat cushion moves smoothly when the battery is connected to the slide motor connector terminals.
| Measurement Condition | Operational Direction |
| Battery positive (+) → Terminal 4 Battery negative (-) → Terminal 1 | Seat cushion moves forward |
| Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 4 | Seat cushion moves backward |
| *a | Component without harness connected (Slide Motor (Separate Type Front Seat Cushion Assembly)) |
![]() |
Check the operation of the front vertical motor.
Check if the seat cushion moves smoothly when the battery is connected to the front vertical motor connector terminals.
| Measurement Condition | Operational Direction |
| Battery positive (+) → Terminal 4 Battery negative (-) → Terminal 1 | Seat cushion moves upward |
| Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 4 | Seat cushion moves downward |
| *a | Component without harness connected (Front Vertical Motor (Separate Type Front Seat Cushion Assembly)) |
![]() |
Check the operation of the lifter motor.
Check if the seat cushion moves smoothly when the battery is connected to the lifter motor connector terminals.
| Measurement Condition | Operational Direction |
| Battery positive (+) → Terminal 4 Battery negative (-) → Terminal 1 | Seat cushion moves upward |
| Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 4 | Seat cushion moves downward |
| *a | Component without harness connected (Lifter Motor (Separate Type Front Seat Cushion Assembly)) |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | ||
| ||
| 5.INSPECT SEPARATE TYPE FRONT SEATBACK ASSEMBLY |
![]() |
Disconnect g3 reclining motor connector.
Check the operation of the reclining motor.
Check if the seatback moves smoothly when the battery is connected to the reclining motor connector terminals.
| Measurement Condition | Operational Direction |
| Battery positive (+) → Terminal 4 Battery negative (-) → Terminal 1 | Seatback moves forward |
| Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 4 | Seatback moves backward |
| *a | Component without harness connected (Reclining Motor (Separate Type Front Seatback Assembly)) |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH (W/ MEMORY) - POWER SEAT MOTOR) |
Disconnect the e11 front power seat switch LH (w/ Memory) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| e11-3 (SLD+) - e8-4 | Always | Below 1 Ω |
| e11-4 (SLD-) - e8-1 | Always | Below 1 Ω |
| e11-5 (FRV-) - e9-1 | Always | Below 1 Ω |
| e11-8 (FRV+) - e9-4 | Always | Below 1 Ω |
| e11-10 (LFT+) - e10-4 | Always | Below 1 Ω |
| e11-12 (LFT-) - e10-1 | Always | Below 1 Ω |
| e11-9 (RCL+) - g3-4 | Always | Below 1 Ω |
| e11-11 (RCL-) - g3-1 | Always | Below 1 Ω |
| e11-3 (SLD+) - Body ground | Always | 10 kΩ or higher |
| e11-4 (SLD-) - Body ground | Always | 10 kΩ or higher |
| e11-5 (FRV-) - Body ground | Always | 10 kΩ or higher |
| e11-8 (FRV+) - Body ground | Always | 10 kΩ or higher |
| e11-10 (LFT+) - Body ground | Always | 10 kΩ or higher |
| e11-12 (LFT-) - Body ground | Always | 10 kΩ or higher |
| e11-9 (RCL+) - Body ground | Always | 10 kΩ or higher |
| e11-11 (RCL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH (W/ MEMORY) - BATTERY) |
Disconnect the e12 front power seat switch LH (w/ Memory) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| e12-12 (SYSB) - Body ground | Always | 11 to 14 V |
|
| ||||
| OK | ||
| ||
| 8.INSPECT LUMBAR FRONT POWER SEAT SWITCH |
Remove the lumbar front power seat switch (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 3 - 5 | Hold | Below 1 Ω |
| 1 - 2 | ||
| 2 - 3 | Off | |
| 2 - 1 | ||
| 2 - 3 | Release | |
| 1 - 5 |
| *1 | Hold Switch |
| *2 | Release Switch |
| *a | Component without harness connected (Lumbar Front Power Seat Switch) |
|
| ||||
| OK | |
| 9.INSPECT LUMBAR SUPPORT ADJUSTER ASSEMBLY (SEPARATE TYPE FRONT SEATBACK ASSEMBLY) |
![]() |
Disconnect g4 lumbar support adjuster assembly connector.
Check the operation of the lumbar support adjuster assembly.
Check that the seatback moves smoothly when the battery is connected to the lumbar support adjuster assembly connector terminals.
| Measurement Condition | Operational Direction |
| Battery positive (+) → Terminal 1 Battery negative (-) → Terminal 2 | Seatback moves forward |
| Battery positive (+) → Terminal 2 Battery negative (-) → Terminal 1 | Seatback moves backward |
| *a | Component without harness connected (Lumbar Support Adjuster Assembly (Separate Type Front Seatback Assembly)) |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH (W/ MEMORY) - LUMBAR FRONT POWER SEAT SWITCH - LUMBAR MOTOR) |
Disconnect the e11 front power seat switch LH (w/ Memory) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| e11-6 (+B2) - e5-5 | Always | Below 1 Ω |
| e11-1 (GND2) - e5-2 | Always | Below 1 Ω |
| e5-3 - g4-1 | Always | Below 1 Ω |
| e5-1 - g4-2 | Always | Below 1 Ω |
| e5-5 - Body ground | Always | 10 kΩ or higher |
| e5-2 - Body ground | Always | 10 kΩ or higher |
| e5-3 - Body ground | Always | 10 kΩ or higher |
| e5-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||