Home › Engine / Hybrid System ยท 2AR-FE › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > INSTALLATION

for Preparation Click here


HINT:
Perform "Inspection After Repair" after replacing the engine assembly (Click here).



1. REMOVE ENGINE STAND
  1. Using a chain block and engine sling device, secure the engine assembly.

    NOTICE:
    1. Adjust the angle of the sling device carefully to prevent the engine assembly or engine hanger from deforming or becoming damaged.
    2. Servicing an engine assembly while it is hanging is dangerous. This can be done only when installing/removing the engine assembly to/from an engine stand.

  1. Remove the engine stand from the engine.



2. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY


    A195875E05
  1. Using SST, hold the crankshaft.

    SST
    09213-54015  
    09330-00021  

    HINT:
    SST (Crankshaft pulley holding tool) Fixing bolt part No. : 91551-80650(2 pcs)

  1. Clean the bolts and their installation holes.



    A196850
  1. Install the front drive plate spacer.

    HINT:
    Align the pin of the front drive plate spacer with the pin hole of the crankshaft.



    A196851E03
  1. Install the drive plate and rear drive plate spacer onto the crankshaft.
    Text in Illustration 
    *1
    Drive Plate
    *2
    Rear Drive Plate Spacer
    V100135
    Transaxle Side



    A192239E03
  1. Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 8 bolts.
    Text in Illustration 
    *1
    Adhesive

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    A196849E01
  1. Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.

    Torque:
    98 N*m{ 999 kgf*cm , 72 ft.*lbf }

    NOTICE:
    Do not start the engine for at least an hour after installing the drive plate.



3. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY


    C201731E03
  1. Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter centerpiece.

    Clutch spline grease:
    Toyota Genuine Clutch Spline Grease or equivalent

    Maximum grease amount:
    Approximately 1 g (0.0353 oz.)

    Text in Illustration 
    *1
    Torque Converter Centerpiece
    *2
    Crankshaft



    C239000E01
  1. While keeping the engine and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and install the 9 bolts shown in the illustration.
    Bolt
    Bolt Length
    Torque
    A
    55 mm (2.17 in.)
    64 N*m (653 kgf*cm, 47 ft.*lbf)
    B
    50 mm (1.97 in.)
    46 N*m (469 kgf*cm, 34 ft.*lbf)
    C
    32 mm (1.26 in.)
    44 N*m (449 kgf*cm, 32 ft.*lbf)
    33 mm (1.30 in.)
    43 N*m (438 kgf*cm, 32 ft.*lbf)

    NOTICE:
    1. Confirm that the 2 knock pins are installed to the transaxle contact surface of the engine cylinder block before installing the automatic transaxle assembly.
    2. Do not forcibly pry on the automatic transaxle assembly.
    3. Check that the torque converter rotates.



4. INSTALL ENGINE MOUNTING BRACKET RH
  1. Install the engine mounting bracket RH with the 3 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }



5. INSTALL DRIVE SHAFT BEARING BRACKET
  1. Install the drive shaft bearing bracket with the 3 bolts.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }



6. TEMPORARILY INSTALL FRONT ENGINE MOUNTING INSULATOR
  1. Temporarily install the front engine mounting insulator with the 3 nuts.

    HINT:
    Perform this procedure only when replacement of the front engine mounting insulator is necessary.



7. TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR LH
  1. Temporarily install the engine mounting insulator LH with the 3 nuts.

    HINT:
    Perform this procedure only when replacement of the engine mounting insulator LH is necessary.



8. TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR RH
  1. Temporarily install the engine mounting insulator RH with the 3 nuts.

    HINT:
    Perform this procedure only when replacement of the engine mounting insulator RH is necessary.



9. INSTALL FRONT FRAME ASSEMBLY
  1. Install the engine mounting insulator LH with the nut.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

  1. Install the engine mounting insulator RH with the nut.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

  1. Install the front engine mounting insulator with the bolt.

    Torque:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }



  1. Fully tighten the 9 temporarily installed nuts of the engine mounting insulators to the specified torque.


    A172973E04


    Text in Illustration 
    *a
    Front Engine Mounting Insulator
    *b
    Engine Mounting Insulator RH
    *c
    Engine Mounting Insulator LH
    -
    -

    HINT:
    Perform this procedure only when replacement of the engine mounting insulator is necessary.

    Torque:
    A:
    58 N*m{ 591 kgf*cm , 43 ft.*lbf }
    B:
    99 N*m{ 1010 kgf*cm , 73 ft.*lbf }



  1. Install the 4 hole plugs.


    A256545E01


    Text in Illustration 
    *a
    Engine Mounting Insulator RH
    *b
    Engine Mounting Insulator LH

    HINT:
    Perform this procedure only when replacement of the engine mounting insulator is necessary.



10. INSTALL GENERATOR ASSEMBLY
for 100 A, 130 A Type:
for 150 A Type:


11. INSTALL COMPRESSOR ASSEMBLY WITH PULLEY


    E227471
  1. Remove the 2 bolts and 2 nuts.



    E227470
  1. Using an E8 "TORX" socket wrench, remove the 2 stud bolts and compressor assembly with pulley.

    HINT:
    Remove the compressor assembly with pulley from the vehicle with the stud bolts remaining in the compressor assembly with pulley.



12. INSTALL V-RIBBED BELT


    A194911E02
  1. Set the V-ribbed belt onto each part as shown in the illustration except the water pump pulley.
    Text in Illustration 
    *1
    Crankshaft
    *2
    Tensioner
    *3
    Generator
    *4
    Water Pump
    *5
    Cooler Compressor

  1. Loosen the V-ribbed belt by turning the belt tensioner clockwise.

  1. Set the V-ribbed belt onto the water pump pulley.

    NOTICE:
    Make sure that the belt is attached to each pulley. In particular, make sure that the belt is securely fitted into the grooves of the crankshaft pulley.



13. INSTALL ENGINE WIRE
  1. Install the engine wire to the engine with transaxle.



14. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
  1. Remove the engine hangers .

  1. Set the engine assembly with transaxle on an engine lifter.

    NOTICE:
    1. Install a height adjustment attachment and plate lift attachment onto the engine assembly with transaxle.
    2. Do not position a height adjustment attachment or plate lift attachment onto the front frame assembly.
    3. To prevent the oil pan from deforming, do not place any attachments onto the oil pan of the engine assembly with transaxle.
    4. Make sure to support the engine assembly with transaxle securely to prevent it from falling.

  1. Install the engine assembly to the vehicle.

    NOTICE:
    Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.

    HINT:
    1. Make sure that the engine is clear of all wiring and hoses.
    2. While raising the engine into the vehicle, do not allow it to contact the vehicle.



    A255454E01
  1. Install the frame side rail plate RH and LH with the 4 bolts and 2 nuts.

    Torque:
    A:
    85 N*m{ 867 kgf*cm , 62 ft.*lbf }
    B:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

  1. Install the front suspension member brace rear RH and LH with the 4 bolts and 2 nuts.

    Torque:
    C:
    85 N*m{ 867 kgf*cm , 62 ft.*lbf }
    D:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

    HINT:
    Perform "Inspection After Repair" after replacing the engine assembly .



15. INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT


    A192239E03
  1. Apply a few drops of adhesive to the first 2 or 3 threads of the 6 drive plate and torque converter assembly setting bolts.
    Text in Illustration 
    *1
    Adhesive

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    A196626
  1. Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.

    Torque:
    41 N*m{ 418 kgf*cm , 30 ft.*lbf }

    NOTICE:
    Install the black colored bolt first, and then the 5 silver colored bolts.



16. INSTALL FLYWHEEL HOUSING UNDER COVER
  1. Install the flywheel housing under cover.



17. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY


    C238511E02
  1. Align the matchmarks and install the steering intermediate shaft to the steering link assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Install the bolt.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }



18. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH
  1. Install a new front drive shaft hole snap ring LH.

    NOTICE:
    Face the end gap of the front drive shaft hole snap ring downward.



19. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
  1. Coat the spline of the front drive inboard joint assembly with ATF WS.

  1. Coat the lip of the transaxle case oil seal with MP grease.



    C165536
  1. Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.

    NOTICE:
    1. Face the end gap of the front drive shaft hole snap ring LH downward.
    2. Do not damage the transaxle case oil seal.
    3. Do not damage the front axle inboard joint boot.
    4. Make sure to center the front drive shaft assembly LH during installation to prevent damage to the front drive shaft hole snap ring LH.

    HINT:
    Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.



  1. for TMMK Made:



      C247220
    1. Apply mineral oil base grease to the areas indicated by the arrows in the illustration on the front drive shaft assembly LH contact surface of the front axle hub bearing.
      Text in Illustration 
      V100155
      Mineral Oil Base Grease

      HINT:
      Apply 0.1 to 0.3 g (0.00353 to 0.0106 oz.) of mineral oil base grease to each area.



    C240136E01
  1. Align the matchmarks and install the front drive shaft assembly LH to the front axle hub sub-assembly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Be careful not to damage the front axle outboard joint boot or speed sensor rotor.



20. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
  1. Coat the spline of the front drive inboard joint assembly with ATF WS.

  1. Coat the lip of the front transaxle case oil seal with MP grease.

  1. Install a new bearing bracket hole snap ring to the front drive shaft assembly RH.

  1. Install the front drive shaft assembly RH.

    NOTICE:
    1. Do not damage the front transaxle case oil seal.
    2. Do not damage the front axle inboard joint boot.
    3. When inserting the front drive shaft assembly RH, keep it level.



    C239409
  1. Install the bearing bracket hole snap ring and a new bolt.

    Torque:
    32 N*m{ 330 kgf*cm , 24 ft.*lbf }



  1. for TMMK Made:



      C247527
    1. Apply mineral oil base grease to the areas indicated by the arrows in the illustration on the front drive shaft assembly RH contact surface of the front axle hub bearing.
      Text in Illustration 
      V100155
      Mineral Oil Base Grease

      HINT:
      Apply 0.1 to 0.3 g (0.00353 to 0.0106 oz.) of mineral oil base grease to each area.



    C240137E01
  1. Align the matchmarks and install the front drive shaft assembly RH to the front axle hub sub-assembly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Be careful not to damage the front axle outboard joint boot or speed sensor rotor.



21. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH


    C238972E03
  1. Connect the front lower No. 1 suspension arm sub-assembly to the front lower ball joint assembly with the bolt and 2 nuts.
    Text in Illustration 
    *A
    for TMC, TMMR Made
    *B
    for TMMK Made
    *a
    20 mm (0.787 in.)
    *b
    22 mm (0.866 in.)
    V100135
    Bolt
    V100136
    Nut

    Torque:
    for TMC, TMMR Made:
    75 N*m{ 765 kgf*cm , 55 ft.*lbf }
    for TMMK Made:
    92 N*m{ 938 kgf*cm , 68 ft.*lbf }

    NOTICE:
    1. The tightening torque for the bolt differs depending on the type of nut.
    2. Make sure to tighten the bolt to the same torque as the nuts.



22. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



23. CONNECT TIE ROD ASSEMBLY LH
  1. Connect the tie rod assembly LH to the steering knuckle with the nut.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Install a new cotter pin.

    NOTICE:
    Further tighten the nut up to 60° if the holes for the cotter pin are not aligned.



24. CONNECT TIE ROD ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



25. INSTALL FRONT SPEED SENSOR LH
  1. Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt and clamp.

    Torque:
    19 N*m{ 192 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Do not twist the front speed sensor when installing it.

    HINT:
    Install the speed sensor harness bracket first and then the front flexible hose.

  1. Install the front speed sensor to the steering knuckle with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Do not twist the front speed sensor when installing it.



26. INSTALL FRONT SPEED SENSOR RH

HINT:
Use the same procedure described for the LH side.



27. INSTALL FRONT STABILIZER LINK ASSEMBLY LH


  1. for Steel Type:



      C242672
    1. Install the front stabilizer link assembly to the front shock absorber assembly with the nut.

      Torque:
      74 N*m{ 755 kgf*cm , 55 ft.*lbf }

      If the ball joint turns together with the nut, use a hexagon wrench to hold the stud bolt.



  1. for Aluminum Type:



      C238963
    1. Install the front stabilizer link assembly to the front shock absorber assembly with the nut.

      Torque:
      for TMC, TMMR Made:
      74 N*m{ 755 kgf*cm , 55 ft.*lbf }
      for TMMK Made:
      125 N*m{ 1275 kgf*cm , 92 ft.*lbf }

      If the ball joint turns together with the nut, use a wrench to hold the stud bolt.



28. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



29. INSTALL FRONT AXLE SHAFT NUT LH
  1. Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using a non-residue solvent.

    NOTICE:
    1. Be sure to perform this work even, when using a new front drive shaft assembly.
    2. Keep the threaded parts free of oil and foreign matter.

  1. Using a socket wrench (30 mm), install the front axle hub shaft nut.

    Torque:
    294 N*m{ 2998 kgf*cm , 217 ft.*lbf }

    NOTICE:
    Stake the nut after inspecting for looseness and runout in the following steps.

    HINT:
    Keep depressing the brake pedal to prevent the front drive shaft from rotating.



30. INSTALL FRONT AXLE SHAFT NUT RH

HINT:
Use the same procedure described for the LH side.



31. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A077857E03
  1. Using a vernier caliper, measure the free length of the compression spring.
    Minimum
    40.5 mm (1.60 in.)

    HINT:
    If the length is less than the minimum, replace the compression spring.

  1. Fully insert a new gasket to the exhaust manifold converter sub-assembly.



    A181728E16
  1. Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold converter sub-assembly.
    Text in Illustration 
    *1
    Exhaust Manifold Converter Sub-assembly
    *2
    Gasket
    *3
    Wooden Block

    NOTICE:
    1. Be sure to install the gasket in the correct direction.
    2. Do not reuse the gasket.
    3. Do not damage the gasket.
    4. Do not push in the gasket by using the exhaust pipe when connecting it.

  1. Install a new gasket to the front exhaust pipe assembly.

  1. Connect the front exhaust pipe assembly to the exhaust pipe support.

  1. Install the front exhaust pipe assembly with the 2 compression springs, 2 bolts and 2 nuts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Connect the heated oxygen sensor connector.



32. CONNECT FUEL TUBE SUB-ASSEMBLY


    B012944
  1. Push in the fuel tube connector to the fuel pipe until the connector makes a "click" sound.

    NOTICE:
    1. Check for damage or contamination on the connected part of the pipe.
    2. Check if the pipe and the connector are securely connected by trying to pull them apart.



    A210152
  1. Install the No. 1 fuel pipe clamp.



33. CONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE (for TMC, TMMR Made)
  1. Remove the vinyl tape from the No. 1 cooler refrigerant suction hose and compressor assembly with pulley.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor assembly with pulley.

    Compressor Oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring to the No. 1 cooler refrigerant suction hose.

  1. Connect the No. 1 cooler refrigerant suction hose to the compressor assembly with pulley with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



34. CONNECT SUCTION HOSE SUB-ASSEMBLY (for TMMK Made)
  1. Remove the vinyl tape from the suction hose sub-assembly and compressor assembly with pulley.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor assembly with pulley.

    Compressor Oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring to the suction hose sub-assembly.

  1. Connect the suction hose sub-assembly to the compressor assembly with pulley with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



35. CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
  1. Remove the vinyl tape from the No. 1 cooler refrigerant discharge hose and compressor assembly with pulley.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor assembly with pulley.

    Compressor Oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring to the No. 1 cooler refrigerant discharge hose.

  1. Connect the No. 1 cooler refrigerant discharge hose to the compressor assembly with pulley with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the 2 connectors.

  1. Install the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



36. CONNECT UNION TO CONNECTOR TUBE HOSE (for LHD)
  1. Connect the union to connector tube hose.



37. CONNECT UNION TO CHECK VALVE HOSE (for RHD)
  1. Connect the union to check valve hose.



38. INSTALL ENGINE MOVING CONTROL ROD
  1. Temporarily install the engine moving control rod to the engine moving control rod bracket with the bolt.

    HINT:
    Perform this procedure only when replacement of the engine moving control rod is necessary.



39. INSTALL ENGINE MOVING CONTROL ROD BRACKET


    A255916E01
  1. When the engine moving control rod has been replaced.

    1. Temporarily install the engine moving control rod bracket with the 4 bolts.

    2. Fully tighten the engine moving control rod bracket with the bolts except bolt A.

      Torque:
      38 N*m{ 387 kgf*cm , 28 ft.*lbf }



    3. A265927E01
    4. Fully tighten the bolt A.

      SST
      09961-00950  

      Torque:
      Without SST:
      52 N*m{ 530 kgf*cm , 38 ft.*lbf }
      With SST:
      33 N*m{ 340 kgf*cm , 25 ft.*lbf }

      NOTICE:
      1. The "with SST" torque value is effective when using SST with a fulcrum length of 150 mm (5.91 in.) and a torque wrench with a fulcrum length of 260 mm (10.24 in.) (Click here).
      2. The "with SST" torque value is effective when SST is parallel to the torque wrench.
      3. Fully tighten bolt A using SST.



    A255452E01
  1. When the engine moving control rod has been reused.

    1. Temporarily install the engine moving control rod bracket with the 4 bolts.

    2. Fully tighten the engine moving control rod bracket with the 4 bolts.

      Torque:
      38 N*m{ 387 kgf*cm , 28 ft.*lbf }



40. INSTALL EARTH WIRE
  1. Install the earth wire with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



41. INSTALL NO. 2 ENGINE MOUNTING STAY RH
  1. Install the No. 2 engine mounting stay RH with the 2 bolts.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }



42. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    C204479
  1. Connect the control cable to the bracket with a new clip.



    C132236
  1. Install the control cable to the control shaft lever with the nut.

    Torque:
    13 N*m{ 131 kgf*cm , 9 ft.*lbf }



43. INSTALL NO. 1 AIR CLEANER BRACKET
  1. Install the No. 1 air cleaner bracket to the battery carrier with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the 2 wire clamps.



44. CONNECT ENGINE WIRE


    A255463
  1. Connect the 2 wire clamps.

  1. Connect the connector to the ECM with the lock lever.

  1. Connect the engine wire to the engine room relay block.

  1. Connect the 4 connectors.



    A255437
  1. Connect the engine wire to the engine room relay block.

  1. Connect the wire clamp and install the 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the No. 1 relay block cover.



45. INSTALL STARTER ASSEMBLY (for 1.6 kW Type)
  1. Install the starter assembly with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the starter connector.

  1. Install the terminal nut and cover the nut with the cap.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



46. INSTALL STARTER ASSEMBLY (for 1.7 kW Type)
  1. Install the starter assembly with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Connect the starter connector.

  1. Install the terminal nut and cover the nut with the cap.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }



47. CONNECT INLET HEATER WATER HOSE
  1. Connect the inlet heater water hose.



48. CONNECT OUTLET HEATER WATER HOSE
  1. Connect the outlet heater water hoses.



49. CONNECT INLET NO. 1 OIL COOLER HOSE
  1. Connect the inlet No. 1 oil cooler hose to the automatic transaxle assembly.



50. CONNECT OUTLET NO. 1 OIL COOLER HOSE
  1. Connect the outlet No. 1 oil cooler hose to the automatic transaxle assembly.



51. CONNECT NO. 1 RADIATOR HOSE
  1. Connect the air fuel ratio sensor wire to the No. 1 radiator hose with the hose clamp.



52. CONNECT NO. 2 RADIATOR HOSE
  1. Connect the No. 2 radiator hose.



53. INSTALL BATTERY
  1. Install the battery and battery tray.

  1. Install the battery clamp with the bolt and nut.

    Torque:
    Bolt:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
    Nut:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

  1. Connect the positive (+) battery terminal

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }



54. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    A255405E01
  1. Insert the projection of the air cleaner case sub-assembly to the hole of the No. 2 air cleaner bracket as shown in the illustration.
    Text in Illustration 
    *a
    Wire harness clamp
    *b
    Hole
    *c
    Projection

  1. Tighten the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the wire harness clamp.



55. INSTALL AIR CLEANER FILTER ELEMENT


56. INSTALL AIR CLEANER CAP SUB-ASSEMBLY
  1. Install the air cleaner cap sub-assembly with the 2 clamps.

  1. Install the air cleaner hose with the hose clamp.

  1. Connect the ventilation hose to the cylinder head cover.

  1. Install the fuel vapor feed hose to the air cleaner hose.

  1. Connect the mass air flow meter connector and 2 wire harness clamps to the air cleaner cap sub-assembly.

  1. Connect the vacuum switching valve assembly to the air cleaner hose.



57. INSTALL INLET AIR CLEANER ASSEMBLY
  1. Install the inlet air cleaner with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



58. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



59. ADD ENGINE OIL


60. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.



    A260080E01
  1. Slowly fill the radiator assembly with engine coolant.
    Text in Illustration 
    *a
    Code Mark
    Specified Capacity 
    Code Mark "M"
    6.9 liters (7.3 US qts, 6.1 Imp. qts)
    Code Mark "G"
    7.0 liters (7.4 US qts, 6.2 Imp. qts)
    Code Mark "Z"
    7.3 liters (7.7 US qts, 6.4 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damaging the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

  1. Remove the reserve tank cap.

  1. Slowly pour engine coolant into the radiator reserve tank assembly until it reaches the full line.

  1. Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the level of the engine coolant.
    If the engine coolant level is low, add engine coolant.

  1. Install the radiator cap sub-assembly and reserve tank cap.

  1. Bleed air from the cooling system.

    NOTICE:
    1. Before starting the engine, turn the A/C switch off.
    2. Adjust the heater control to the maximum hot setting.
    3. Adjust the blower speed to the low setting.


    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the No. 2 radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the No. 2 radiator hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air from the cooling system.

      CAUTION:
      When squeezing the No. 1 radiator hose and No. 2 radiator hose:
      1. Wear protective gloves.
      2. Be careful as the No. 1 radiator hose and No. 2 radiator hose are hot.
      3. Keep your hands away from the fan and No. 2 fan.

      NOTICE:
      1. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      2. Make sure that the radiator reserve tank assembly still has some engine coolant in it.
      3. If the radiator reserve tank assembly does not have enough engine coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reserve tank assembly does not have enough engine coolant, perform the following: 1) stop the engine, 2) wait until the engine coolant has cooled down, and 3) add engine coolant until the radiator reserve tank assembly is filled to the full line.

  1. Stop the engine, and wait until the engine coolant cools down.

  1. Add engine coolant to the full line on the radiator reserve tank assembly.



61. ADD AUTOMATIC TRANSAXLE FLUID
(Click here)


62. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for TMC, TMMR Made)
  1. Perform vacuum purging using a vacuum pump or appropriate equipment.



  1. Charge the air conditioning system with refrigerant.

    Refrigerant type:
    HFC-134a (R134a)



    E143108E14


    Text in Illustration 
    *a
    Sub-cool System
    *b
    High Pressure
    *c
    Refrigerant Amount
    *d
    Standard charge amount
    *e
    Charge additional 100 g (3.5 oz)
    *f
    Point where bubbles disappear
    *g
    Mean value in proper range
    *h
    Overcharged
    *i
    +/-50 g (+/-1.76 oz)
    -
    -

    Standard charge amount:
    450 to 550 g (15.9 to 19.4 oz)

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    NOTICE:
    1. Do not turn the A/C switch on before charging the air conditioning system with refrigerant. Doing so may cause the compressor to work without refrigerant, resulting in overheating of the compressor.
    2. The refrigerant amount should be checked by quantity (weight).

    HINT:
    Ensure that sufficient refrigerant is available to recharge the system when using a refrigerant recovery unit. Refrigerant recovery units are not always able to recover 100% of the refrigerant from an air conditioning system.



63. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for TMMK Made)
  1. Perform vacuum purging using a vacuum pump or appropriate equipment.



  1. Charge the air conditioning system with refrigerant.

    Refrigerant type:
    HFC-134a (R134a)



    E247093E08


    Text in Illustration 
    *a
    Standard Charge Amount
    *b
    Mean Value in Proper Range
    *c
    Overcharged
    *d
    High Pressure
    *e
    Sub-cool System
    *f
    Refrigerant Amount
    *g
    +/-50 g (+/-1.76 oz)
    -
    -

    Standard charge amount:
    450 to 550 g (15.9 to 19.3 oz)

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    NOTICE:
    1. Do not turn the A/C switch on before charging the air conditioning system with refrigerant. Doing so may cause the compressor to work without refrigerant, resulting in overheating of the compressor.
    2. The refrigerant amount should be checked by quantity (weight).
    3. The graph above is shown for reference only.

    HINT:
    Ensure that sufficient refrigerant is available to recharge the system when using a refrigerant recovery unit. Refrigerant recovery units are not always able to recover 100% of the refrigerant from an air conditioning system.



64. WARM UP ENGINE (for TMC, TMMR Made)
  1. Keep the A/C switch on for at least 2 minutes to warm up the compressor.

    NOTICE:
    To prevent damage to the compressor, be sure to warm up the compressor when turning the air conditioning on after removing and installing air conditioning system lines (including the compressor).



65. WARM UP ENGINE (for TMMK Made)
  1. Keep the A/C switch on for at least 2 minutes to warm up the compressor.

    NOTICE:
    To prevent damage to the compressor, be sure to warm up the compressor when turning the air conditioning on after removing and installing any air conditioning system lines (including the compressor).



66. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the intelligent tester on.

      NOTICE:
      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

    4. Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.

  1. Inspect for fuel leaks.

    1. Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the ignition switch off.

  1. Disconnect the intelligent tester from the DLC3.



67. INSPECT FOR OIL LEAK


68. INSPECT FOR COOLANT LEAK

NOTICE:
Before performing each inspection, turn the A/C switch off.



    A255285
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.



69. INSPECT FOR EXHAUST GAS LEAK


70. INSPECT FOR REFRIGERANT LEAK (for TMC, TMMR Made)
  1. After recharging the air conditioning system with refrigerant, check for refrigerant leaks using a halogen leak detector.

  1. Carry out the test under the following conditions:

    1. Turn the engine switch off.
    2. Measure the pressure to make sure that there is some refrigerant remaining in the air conditioning system.
      Pressure when the compressor is off: approx. 392 to 588 kPa (3.9 to 5.9 kgf/cm2, 57 to 85 psi)
    3. Ensure good ventilation (the halogen leak detector may react to volatile gases which are not refrigerant, such as gasoline vapor and exhaust gas).
    4. Repeat the inspection 2 or 3 times.

  1. Remove the front outer cowl top panel sub-assembly .

  1. Remove the radiator side deflector RH .



    E280082E01
  1. How to check for refrigerant leaks in pipe joints:
    Text in Illustration 
    *a
    Check for leaks
    *b
    Halogen Leak Detector Sensor
    *c
    Distance between Sensor and Joint to be Checked:
    10 mm or less
    *d
    Halogen Leak Detector Sensor Moving Speed:
    25 to 50 mm/sec.

    NOTICE:
    Gas leaking from a joint can be dissipated by even the slightest breeze. Move the halogen leak detector sensor 360° around each joint instead of keeping it in one spot when checking.



  1. Using a halogen leak detector, check for refrigerant leaks at the pipe joints shown in the illustration.


    E288035E01


    Text in Illustration 
    *a
    Area to be Checked
    *b
    Service Valve (High)
    *c
    Service Valve (Low)
    *d
    Pipe Joint
    *e
    Air Conditioner Pressure Sensor Joint
    *f
    Cooler Expansion Valve Joint
    *g
    Condenser Joint (Inlet)
    *h
    Condenser Joint (Outlet)
    *i
    Compressor Joint (Inlet)
    *j
    Compressor Joint (Outlet)

    HINT:
    1. After the blower motor has stopped, leave the cooling unit for more than 15 minutes.
    2. Disconnect the pressure sensor connector and leave it for approximately 20 minutes.
    3. When checking for leaks, the presence of oily dirt at a joint can indicate a leak.

    Standard:
    There are no refrigerant leaks from the joints.

    If refrigerant is leaking, disconnect the leaking joint and visually check for the cause, such as the presence of foreign matter.



    E280081E01
  1. Bring the halogen leak detector sensor close to the drain cooler hose with the detector turned off, and then turn the detector on.
    Text in Illustration 
    *1
    Drain Cooler Hose
    *a
    Halogen Leak Detector

    NOTICE:
    Keep water away from the halogen leak detector to prevent malfunction.

    HINT:
    1. After the blower motor has stopped, leave the cooling unit for more than 15 minutes.
    2. When bringing the halogen leak detector sensor close to the drain cooler hose, make sure that the halogen leak detector does not react to volatile gases. If it is not possible to avoid interference from volatile gases, the vehicle should be lifted up to allow checking for leaks.

    Standard:
    Refrigerant is not leaking from the drain cooler hose.

    If refrigerant is leaking, check for refrigerant leaks from the No. 1 cooler evaporator sub-assembly.

  1. Remove the blower motor with fan sub-assembly (Click here).



    E288039E01
  1. Insert the halogen leak detector sensor into the air conditioning unit assembly, bring the sensor close to the No. 1 cooler evaporator sub-assembly and check for refrigerant leaks.
    Text in Illustration 
    *1
    No. 1 Cooler Evaporator Sub-assembly
    *a
    Halogen Leak Detector

    HINT:
    After the blower motor has stopped, leave the cooling unit for more than 15 minutes.

    Standard:
    Refrigerant is not leaking from the No. 1 cooler evaporator sub-assembly.

    If refrigerant is leaking, disconnect the leaking joint and visually check for the cause, such as the presence of foreign matter.

  1. Install the blower motor with fan sub-assembly (Click here).

  1. Install the radiator side deflector RH .

  1. Install the front bumper assembly (Click here).

  1. Install the front outer cowl top panel sub-assembly .

  2. See the table below for possible causes, and then inspect and correct the applicable causes if necessary.

    CO
    HC
    Symptom
    Causes
    Normal
    High
    Rough idle
    1. 1. Faulty ignition
      1. Incorrect timing
      2. Plugs are contaminated or shorted, or gaps are defective
    2. 2. Leaky intake and exhaust valves
    3. 3. Leaky cylinder
    Low
    High
    Rough idle
    (Fluctuating HC reading)
    1. 1. Vacuum leaks
      1. PCV hose
      2. Intake manifold
      3. Throttle body
      4. Brake booster line
    2. 2. Lean mixture causing misfire
    High
    High
    Rough idle
    (Black smoke from exhaust)
    1. 1. Restricted air filter
    2. 2. Faulty SFI system
      1. Faulty pressure
      2. Defective ECT sensor
      3. Faulty ECM
      4. Faulty injector
      5. Faulty throttle position sensor
      6. Faulty MAF sensor



75. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
  1. Fit the 3 retainers and install the No. 1 engine cover sub-assembly.



76. INSTALL COOL AIR INTAKE DUCT SEAL (for TMC, TMMR Made)
  1. Install the cool air intake duct seal with the 9 clips.



77. INSTALL COOL AIR INTAKE DUCT SEAL (for TMMK Made)
  1. Install the cool air intake duct seal with the 9 clips.



78. INSPECT AND ADJUST SHIFT LEVER POSITION
(Click here)


79. INSTALL FRONT FENDER APRON SEAL LH


80. INSTALL FRONT FENDER APRON SEAL RH


81. INSTALL ENGINE UNDER COVER LH


82. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH


83. INSTALL ENGINE UNDER COVER RH


84. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH


85. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1049 kgf*cm , 76 ft.*lbf }



86. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
for TMC, TMMR Made: (Click here)
for TMMK Made: (Click here)


87. CHECK SPEED SENSOR SIGNAL
(Click here)