Home › Engine / Hybrid System · 2AR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0365    Camshaft Position Sensor "B" Circuit (Bank 1)

DTC    P0367    Camshaft Position Sensor "B" Circuit Low Input (Bank 1)

DTC    P0368    Camshaft Position Sensor "B" Circuit High Input (Bank 1)

for Preparation Click here


DESCRIPTION

The camshaft position sensor for the exhaust camshaft (EV1 signal) consists of a magnet and MRE (Magneto Resistance Element).
The exhaust camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection duration, injection timing and the Variable Valve Timing (VVT) system.

DTC No.
DTC Detection Condition
Trouble Area
P0365
No exhaust camshaft position sensor signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic).
  1. Open or short in camshaft position sensor circuit (for exhaust camshaft)
  2. Camshaft position sensor (for exhaust camshaft)
  3. Exhaust camshaft
  4. Valve timing
  5. ECM
P0367
The output voltage of the exhaust camshaft position sensor is less than 0.3 V for 4 seconds (1 trip detection logic).
  1. Open or short in camshaft position sensor circuit (for exhaust camshaft)
  2. Camshaft position sensor (for exhaust camshaft)
  3. ECM
P0368
The output voltage of the exhaust camshaft position sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
  1. Open or short in camshaft position sensor circuit (for exhaust camshaft)
  2. Camshaft position sensor (for exhaust camshaft)
  3. ECM

HINT:
Reference: Inspection using an oscilloscope .


MONITOR DESCRIPTION

If no pulse signal is transmitted by the camshaft position sensor for exhaust camshaft despite the camshaft revolving, or the rotation of the exhaust camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.
Also, when the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds or more, the ECM stores a DTC.

MONITOR STRATEGY


Required Sensors/Components (Main)
Exhaust camshaft position sensor
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the tester on.
  6. Start the engine.
  7. Idle the engine for 10 seconds or more.
  8. Enter the following menus: Powertrain / Engine and ECT / DTC.
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0365, P0367 or P0368.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


WIRING DIAGRAM


A255253E04


INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR)


    A194108E71
  1. Disconnect the camshaft position sensor for exhaust camshaft connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E52-3 (VC2) - Body ground
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Camshaft Position Sensor for Exhaust Camshaft)



NG
Go to step 8
OK


2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
  1. Disconnect the camshaft position sensor for exhaust camshaft connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E52-1 (VVE+) - E26-81 (EV1+)
    Always
    Below 1 Ω
    E52-2 (VVE-) - E26-112 (EV1-)
    Always
    Below 1 Ω
    E52-1 (VVE+) or E26-81 (EV1+) - Body ground
    Always
    10 kΩ or higher
    E52-2 (VVE-) or E26-112 (EV1-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT)


    BR03795E17
  1. Check the camshaft position sensor for exhaust camshaft installation.

    OK:
    Camshaft position sensor is installed correctly.



NG
SECURELY REINSTALL CAMSHAFT POSITION SENSOR (Click here)
OK


4.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)
  1. Check the timing rotor of the exhaust camshaft.

    OK:
    Camshaft timing rotor does not have any cracks or deformation.

    HINT:
    Perform "Inspection After Repair" after replacing the exhaust camshaft (Click here).



NG
REPLACE EXHAUST CAMSHAFT (Click here)
OK


5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

A200659E02


Text in Illustration 
*1
Timing Mark
-
-
  1. Remove the cylinder head cover sub-assembly.

  1. Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.

  1. Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.

    HINT:
    If the timing marks are not as shown, turn the crankshaft one revolution clockwise.

    OK:
    Timing marks on camshaft timing gear assembly and camshaft timing exhaust gear assembly are aligned as shown in the illustration.



NG
ADJUST VALVE TIMING (Click here)
OK


6.REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)
  1. Replace the camshaft position sensor (for exhaust camshaft) (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0367 OR P0368)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Start the engine.

  1. Turn the tester on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0365, P0367 or P0368 is output
    A
    DTC is not output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
END
A

REPLACE ECM (Click here)  

8.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
  1. Disconnect the camshaft position sensor for exhaust camshaft connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E52-3 (VC2) - E26-111 (VCE1)
    Always
    Below 1 Ω
    E52-3 (VC2) or E26-111 (VCE1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)