DTC B1771 Passenger Side Buckle Switch Circuit Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1771 |
|
|

| 1.CHECK CONNECTORS |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the occupant detection ECU and front seat inner belt assembly RH.
Disconnect the connectors from the occupant detection ECU and front seat inner belt assembly RH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 2.CHECK FRONT SEAT WIRE RH (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| d11-8 (BSW) - Body ground | Engine switch on (IG) | Below 1 V |
| d11-5 (BGND) - Body ground | Engine switch on (IG) | Below 1 V |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
| *1 | Front Seat Inner Belt Assembly RH |
| *2 | Occupant Detection ECU |
| *3 | Front Seat Wire RH |
| *a | Front view of wire harness connector (to Occupant Detection ECU) |
|
| ||||
| OK | |
| 3.CHECK FRONT SEAT WIRE RH (OPEN) |
![]() |
Using a service wire, connect terminals BSW and BGND of connector C as shown in the illustration.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| d11-8 (BSW) - d11-5 (BGND) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
| *1 | Front Seat Inner Belt Assembly RH |
| *2 | Occupant Detection ECU |
| *3 | Front Seat Wire RH |
| *4 | Service Wire |
| *a | Front view of wire harness connector (to Occupant Detection ECU) |
| *b | Front view of wire harness connector (to Front Seat Inner Belt Assembly RH) |
|
| ||||
| OK | |
| 4.CHECK FRONT SEAT WIRE RH (SHORT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| d11-8 (BSW) - d11-5 (BGND) | Always | 1 MΩ or higher |
| *1 | Front Seat Inner Belt Assembly RH |
| *2 | Occupant Detection ECU |
| *3 | Front Seat Wire RH |
| *a | Front view of wire harness connector (to Occupant Detection ECU) |
|
| ||||
| OK | |
| 5.CHECK FRONT SEAT WIRE RH (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| d11-8 (BSW) - Body ground | Always | 1 MΩ or higher |
| d11-5 (BGND) - Body ground | Always | 1 MΩ or higher |
| *1 | Front Seat Inner Belt Assembly RH |
| *2 | Occupant Detection ECU |
| *3 | Front Seat Wire RH |
| *a | Front view of wire harness connector (to Occupant Detection ECU) |
|
| ||||
| OK | |
| 6.CHECK DTC |
Connect the connectors to the occupant detection ECU and front seat inner belt assembly RH.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in the occupant detection ECU (Click here).
Clear the DTCs stored in the airbag sensor assembly (Click here).
Turn the engine switch off.
Turn the engine switch on (IG).
Check for DTCs (Click here).
Turn the engine switch off.
|
| ||||
| OK | ||
| ||
| 7.CHECK FRONT SEAT INNER BELT ASSEMBLY RH |
Disconnect the cable from the negative (-) battery terminal.
Replace the front seat inner belt assembly RH with a known good one (Click here).
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in the occupant detection ECU (Click here).
Clear the DTCs stored in the airbag sensor assembly (Click here).
Turn the engine switch off.
Turn the engine switch on (IG).
Check for DTCs (Click here).
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Restore the front seat inner belt assembly RH that was installed for testing to its original location (Click here).
|
| ||||
| OK | ||
| ||
| 8.REPLACE OCCUPANT DETECTION ECU |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Replace the occupant detection ECU with a new one (Click here).
Connect the cable to the negative (-) battery terminal.
| NEXT | |
| 9.PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK |
Using the GTS, perform Zero Point Calibration and Sensitivity Check (Click here).
| NEXT | ||
| ||