Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows)

POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on Front Door Windows) > Remote Up / Down Function does not Operate

for Preparation Click here


DESCRIPTION

Front passenger door:
When the engine switch is on (IG), the power window regulator master switch assembly sends remote up and down signals to the power window regulator motor assembly (for front passenger door) via LIN communication.
Rear doors:
When the engine switch is on (IG), the power window regulator master switch assembly sends remote up and down signals to the rear power window regulator switch assembly (for LH door or RH door). Then, the rear power window regulator switch assembly (for LH door or RH door) drives each power window regulator motor assembly.

WIRING DIAGRAM

Refer to System Diagram (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly (Click here).
  2. If the power window regulator motor assembly (for front passenger door) has been replaced with a new one, initialize the power window control system (Click here).
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (WINDOW LOCK SWITCH)
  1. Turn the window lock switch off and operate the switches on the power window regulator master switch assembly. Check that the remote up and down function operates normally.

    OK:
    Remote up and down function operates normally.

    Result::
    Result
    Proceed to
    OK
    A
    NG (Front passenger door power window remote up and down function does not operate)
    B
    NG (Rear LH door power window remote up and down function does not operate)
    C
    NG (Rear RH door power window remote up and down function does not operate)



B
Go to step 2

C
Go to step 4
A

END 

2.READ VALUE USING GTS (MAIN BODY)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the GTS.

    Main Body 
    Tester Display
    Measurement Item
    Normal Condition
    Diagnostic Note
    Communication P-Door Motor
    Connection status between power window regulator motor assembly (for front passenger door) and main body ECU (multiplex network body ECU) / STOP or OK
    STOP: Communication stopped
    OK: Normal communication
    -
    Communication Master SW
    Connection status between power window regulator master switch assembly and main body ECU (multiplex network body ECU) / STOP or OK
    STOP: Communication stopped
    OK: Normal communication
    -

    OK:
    On the GTS screen, OK is displayed.



NG
GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting) (Click here)
OK


3.READ VALUE USING GTS (MASTER SWITCH)
  1. Enter the following menus: Body Electrical / Master Switch / Data List.

  1. Read the Data List according to the display on the GTS.

    Body Electrical > Master Switch > Data List 
    Tester Display
    Measurement Item
    Normal Condition
    Diagnostic Note
    P Door P/W Auto SW
    Front passenger door power window auto up and down switch signal / OFF or ON
    OFF: Front passenger door power window auto switch not being operated
    ON: Front passenger door power window auto switch being operated
    -
    P Door P/W Up SW
    Front passenger door power window manual up switch signal / OFF or ON
    OFF: Front passenger door power window manual up switch not being operated
    ON: Front passenger door power window manual up switch being operated
    -
    P Door P/W Down SW
    Front passenger door power window manual down switch signal / OFF or ON
    OFF: Front passenger door power window manual down switch not being operated
    ON: Front passenger door power window manual down switch being operated
    -
    Window Lock Switch Status
    Window lock switch signal / OFF or ON
    OFF: Window lock switch UNLOCK position
    ON: Window lock switch LOCK position
    -

    OK:
    On the GTS screen, ON or OFF is displayed accordingly.



NG
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) (Click here)  

4.CHECK POWER WINDOW CONTROL SYSTEM (USING REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY)
  1. Check the operation of the rear LH and rear RH door power windows by using the rear power window regulator switch assembly (for LH door or RH door).

    Result::
    Result
    Proceed to
    1. Rear LH and rear RH door power windows operate normally by using the rear power window regulator switch assembly (for LH door or RH door)
    2. Rear LH and rear RH door power windows do not operate by using the rear power window regulator switch assembly (for LH door or RH door)
    A
    Only rear LH door power window does not operate using the rear power window regulator switch assembly (for LH door)
    B
    Only rear RH door power window does not operate using the rear power window regulator switch assembly (for RH door)
    C



B
GO TO OTHER PROBLEM (Rear Power Window LH does not Operate with Rear Power Window Switch LH)

C
GO TO OTHER PROBLEM (Rear Power Window RH does not Operate with Rear Power Window Switch RH)
A

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)