Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Fuel Receiver Gauge Malfunction

for Preparation Click here


DESCRIPTION

  1. The combination meter assembly uses the fuel sender gauge assembly to determine the level of the fuel in the fuel tank. The resistance of the fuel sender gauge will vary between approximately 13 Ω with the float at the full position, and 414 Ω with the float at the empty position. The meter outputs battery voltage through two resistors that are mounted inside the combination meter assembly. The combination meter assembly measures the voltage between the variable resistor in the fuel sender gauge and the two resistors mounted in the meter. Voltage measured at this point will vary as the float of the fuel sender gauge is moved. The highest voltage observed should be approximately half of the battery voltage.

HINT:
The fuel level warning light will come on when the volume of fuel in the fuel tank is as follows:
  1. except TMMK Made: Below 10.5 liters (11.1 US qts, 9.2 Imp. qts)
  2. for TMMK Made: Below 9.7 liters (10.3 US qts, 8.5 Imp. qts)


WIRING DIAGRAM


E230580E14


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. Perform the Active Test according to the display on the GTS.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Fuel Meter Operation
    Fuel receiver gauge
    OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full, Sender F
    -

    OK:
    Fuel receiver gauge indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


2.READ VALUE USING GTS (FUEL INPUT)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter following menus: Body Electrical / Combination Meter / Data List.

  1. Read the Data List according to the display on the GTS.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Input*1
    Fuel input/Min.: 0 L, Max.: 127.5 L
    Fuel receiver gauge indicates F: 62.9
    Unit: Liter
    Fuel receiver gauge indicates 3/4: 54.4
    Fuel receiver gauge indicates 1/2: 35.0
    Fuel receiver gauge indicates 1/4: 15.4
    Fuel receiver gauge indicates E: 7.0
    Fuel Input*2
    Fuel input/Min.: 0 L, Max.: 127.5 L
    Fuel receiver gauge indicates F: 57.9
    Unit: Liter
    Fuel receiver gauge indicates 3/4: 45.6
    Fuel receiver gauge indicates 1/2: 32.2
    Fuel receiver gauge indicates 1/4: 18.9
    Fuel receiver gauge indicates E: 6.4

    1. *1: except TMMK Made
    2. *2: for TMMK Made

    Result:

    Result
    Proceed to
    Fuel level data displayed on the GTS is almost the same as the fuel receiver gauge indication.
    A
    Fuel level data displayed on the GTS differs from the fuel receiver gauge indication.
    B



B
REPLACE COMBINATION METER ASSEMBLY (Click here)
A


3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
  1. Disconnect the I18 combination meter assembly and N11 fuel suction tube assembly with pump and gauge connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I18-14 (FR) - N11-2 (FS)
    Always
    Below 1 Ω
    I18-15 (FE) - N11-3 (FE)
    Always
    Below 1 Ω
    I18-14 (FR) - Body ground
    Always
    10 kΩ or higher
    I18-15 (FE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FUEL SENDER GAUGE ASSEMBLY
  1. Remove the fuel sender gauge assembly (Click here for 2AR-FE (except TMMK Made), Click here for 2AR-FE (for TMMK Made), Click here for 2GR-FE, Click here for 6AR-FSE).

  1. Inspect the fuel sender gauge assembly (Click here for 2AR-FE (except TMMK Made), Click here for 2AR-FE (for TMMK Made), Click here for 2GR-FE, Click here for 6AR-FSE).

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2AR-FE) (except TMMK Made)
    B
    NG (for 2AR-FE) (for TMMK Made)
    C
    NG (for 2GR-FE)
    D
    NG (for 6AR-FSE)
    E



B
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

C
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

D
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

E
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)