WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Entry and Start System) > Only Wireless Control Function is Inoperative |

| 1.CHECK POWER DOOR LOCK OPERATION |
When the door control switch on the multiplex network master switch assembly is operated, check that the locked doors unlock (Click here).
|
| ||||
| OK | |
| 2.CHECK KEY REMINDER WARNING SYSTEM |
Check that the key reminder warning buzzer operates normally (Click here).
|
| ||||
| OK | |
| 3.CHECK DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY |
When a known good registered door control transmitter module set sub-assembly is used, check that the wireless functions operate normally.
| Result | Proceed to |
| Wireless door lock/unlock function operates normally with a known good door control transmitter module set sub-assembly. | A |
| Wireless door lock/unlock function does not operate. | B |
|
| ||||
| A | |
| 4.CHECK TRANSMITTER BATTERY |
Check the transmitter battery level of the door control transmitter module set sub-assembly that was checked first.
Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.
| Result | Proceed to |
| Transmitter LED does not illuminate when switch is pressed and held | A |
| Transmitter LED illuminates 3 times or more when switch is pressed and held | B |
| Transmitter LED illuminates once or twice but not a third time | C |
|
| ||||
|
| ||||
| A | |
| 5.CHECK TRANSMITTER BATTERY (VOLTAGE) |
Inspect the battery capacity. (Type A)
Remove the transmitter battery from the door control transmitter module set sub-assembly that does not operate (Click here). Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative (-) terminal.
![]() |
Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery. (Type A)
![]() |
Check the transmitter battery voltage. (Type A)
| Item | Content |
| Tester Connection | Transmitter battery positive (+) - Transmitter Battery negative (-) |
| Condition | Ignition switch off, all doors closed and lock or unlock switch pressed |
| Specified Condition | 2.2 to 3.2 V |
Inspect the battery capacity. (Type B)
Remove the transmitter battery from the door control transmitter module set sub-assembly that does not operate (Click here). Attach a lead wire (0.6 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative (-) terminal.
![]() |
Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery. (Type B)
![]() |
Check the transmitter battery voltage. (Type B)
| Item | Content |
| Tester Connection | Transmitter battery positive (+) - Transmitter Battery negative (-) |
| Condition | Ignition switch off, all doors closed and lock or unlock switch pressed |
| Specified Condition | 2.2 to 3.2 V |
|
| ||||
| OK | ||
| ||
| 6.CHECK WAVE ENVIRONMENT |
Bring the door control transmitter module set sub-assembly near the door control receiver, and perform a wireless operation check.
|
| ||||
| OK | ||
| ||
| 7.SWITCH TO SELF-DIAGNOSTIC MODE |
Switch to self-diagnostic mode by operating the ignition key cylinder.
Make sure that the vehicle is in its initial condition. Then insert the key into the ignition key cylinder and remove it.
Within 5 seconds after removing the key, insert the key into the ignition key cylinder (ignition switch off). Then turn the ignition switch to ON and off.
Within 30 seconds after turning the ignition switch off, perform the following operation 9 times: turn the ignition switch to ON and then off.
![]() |
Check that the system has switched to self-diagnostic mode by checking the room light output pattern.
![]() |
Check that the system has switched to self-diagnostic mode by checking the wireless door lock buzzer output pattern*.
*: w/ Wireless Door Lock Buzzer Answer Back Function
| NEXT | |
| 8.CHECK SELF DIAGNOSTIC MODE |

Inspect the diagnostic outputs when the door control transmitter module set sub-assembly switch is held down. The diagnostic outputs can be checked by the flash patterns of the interior lights and the buzzer patterns of the wireless door lock buzzer*.
| Result | Proceed to |
| Normal wave (light flash pattern and buzzer pattern) is output. | A |
| Unmatching recognition code is output. | B |
| No diagnostic outputs. | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 9.REGISTER RECOGNITION CODE |
Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered (Click here).
|
| ||||
| OK | ||
| ||
| 10.CHECK DOOR CONTROL RECEIVER (RESPONSE) |
Prepare the door control transmitter module set sub-assembly from another vehicle.
Press and hold down the door control transmitter module set sub-assembly switch.
Check that an unmatching recognition code is output.
|
| ||||
| OK | ||
| ||
| 11.CHECK DOOR CONTROL RECEIVER (+B, GND) |
![]() |
Disconnect the O24 door control receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O24-1 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O24-5 (+B) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector (to Door Control Receiver) |
|
| ||||
| OK | |
| 12.CHECK DOOR CONTROL RECEIVER (OUTPUT) |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O24-2 (RDA) - Body ground | Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch not pressed | 11 to 14 V |
| Ignition switch off, all doors closed and door control transmitter module set sub-assembly switch pressed | Pulse generation |
| *a | Component with harness connected (Door Control Receiver) |
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - DOOR CONTROL RECEIVER) |
Disconnect the I13 main body ECU (multiplex network body ECU) connector and the O24 door control receiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I13-16 (RDA) - O24-2 (RDA) | Always | Below 1 Ω |
| I13-16 (RDA) or O24-2 (RDA) - Body ground | Always | 10 kΩ or higher |
| I13-4 (PRG) - O24-3 (PRG) | Always | Below 1 Ω |
| I13-4 (PRG) - or O24-3 (PRG) Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 14.REPLACE DOOR CONTROL RECEIVER |
Temporarily replace the door control receiver with a new or known good one (Click here).
| NEXT | |
| 15.REGISTER RECOGNITION CODE |
Perform the Registration procedure (Click here).
| NEXT | |
| 16.CHECK DOOR CONTROL RECEIVER (OPERATION) |
Check that the doors can be locked and unlocked by using the door control transmitter module set sub-assembly lock and unlock switches.
|
| ||||
| OK | ||
| ||