Home › Engine / Hybrid System ยท 2GR-FE › STARTING › ENGINE SWITCH

ENGINE SWITCH > INSTALLATION

for Preparation Click here



1. INSTALL ENGINE SWITCH
  1. Engage the 2 claws to install the engine switch.



2. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
  1. for LHD with Smart Entry and Start System:

    1. Connect the connector.

  1. Engage the 3 clips and guide to install the lower instrument panel finish panel assembly.



3. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    B281776
  1. Engage the clip and 4 guides as shown in the illustration.

  1. Install the front No. 2 console box insert with the 2 screws <D>.

  1. for LHD:

    1. Engage the 2 claws to connect the room temperature sensor.



4. INSTALL CONSOLE BOX ASSEMBLY
(Click here).


5. INSTALL FRONT ASH RECEPTACLE ASSEMBLY
  1. Connect each connector.



    B384414
  1. Engage the 2 clips.

  1. Install the front ash receptacle assembly with the 2 screws <D>.



6. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
  1. w/o Driver Side Knee Airbag:

    1. Engage the 5 clips and 3 guides.

  1. w/ Driver Side Knee Airbag:

    1. Engage the 4 claws, 7 clips and 3 guides.

  1. Install the instrument panel sub-assembly with the 2 bolts <B>.



7. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
  1. Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.



8. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    B386776
  1. Temporarily install the instrument cluster finish panel assembly as shown in the illustration.

  1. Connect each connector.

  1. for LHD:

    1. Engage the 3 claws, 7 clips and 4 guides.

  1. for RHD:

    1. Engage the 4 claws, 5 clips and 4 guides.



    B384403
  1. Engage the 4 clips and 2 guides to install the instrument cluster finish panel assembly.



9. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    B280325
  1. Engage the 4 clips to install the No. 1 instrument panel register assembly.



10. INSTALL INSTRUMENT SIDE PANEL LH
  1. Engage the 3 guides.



    B280321
  1. Engage the 4 claws to install the instrument side panel LH as shown in the illustration.



11. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B278980E01
  1. Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
    Text in Illustration 
    *1
    Alignment Mark (Yellow)

    NOTICE:
    After installation, check that the corners fit correctly.



12. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
  1. Engage the 2 clips.

  1. Install the cowl side trim sub-assembly LH with the clip.



13. INSTALL FRONT DOOR SCUFF PLATE LH
  1. Engage the 10 claws to install the front door scuff plate LH.



14. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY
(Click here).


15. INSTALL RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY
(Click here).


16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Manual Tilt and Manual Telescopic Steering Column)

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Power Tilt and Power Telescopic Steering Column)

NOTICE:
  1. Reset the auto away/return function setting to the previous condition by changing the customize parameter (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).