SMART ENTRY AND START SYSTEM (for Start Function) > Power Source Mode does not Change to ON (IG and ACC) |


| Problem Symptom | Data List Item | Active Test Item |
| Power source mode does not change to on (IG) or on (ACC) | Power Source Control
| - |
| 1.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM |
Check the wireless door lock function by operating the electrical key transmitter sub-assembly.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (POWER SOURCE) |
![]() |
Disconnect the A43 connector from the certification ECU (smart key ECU assembly).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A43-2 (+B) - Body ground | Always | 11 to 14 V |
| *a | Rear view of wire harness connector (to Certification ECU (smart key ECU assembly)) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A43-11 (E) - Body ground | Always | Below 1 Ω |
| *a | Rear view of wire harness connector (to Certification ECU (smart key ECU assembly)) |
|
| ||||
| OK | |
| 4.CHECK SMART ENTRY AND START SYSTEM |
Remove the battery from the electrical key transmitter sub-assembly (Click here).
![]() |
With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the engine switch and check if the power source mode changes.
| Result | Proceed to |
| The power source mode does not change. | A |
| The power source mode changes. | B |
| *A | for Type A |
| *B | for Type B |
| *1 | Engine Switch |
| *2 | Electrical Key Transmitter Sub-assembly |
|
| ||||
| A | |
| 5.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
Enter the following menus: Body / Power Source Control / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Specified Condition |
| Stop Light Switch1 | State of brake pedal/ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released |
|
|
| ||||
| OK | |
| 6.READ VALUE USING INTELLIGENT TESTER |
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Power Supply Condition | Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON | All OFF: Engine switch off (ACC and IG) ACC ON: Engine switch on (ACC) IG1 ON: Engine switch on (IG) (IG1 relay on) IG2 ON: Engine switch on (IG) (IG2 relay on) ST ON: Sending engine start request signal | Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time). |
With the engine switch off and brake pedal depressed, hold the electrical key transmitter sub-assembly near the engine switch for 2 seconds or more and read the Data List.
|
| ||||
| OK | |
| 7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Read the Data List according to the display on the intelligent tester.
Measure the voltage according to the value(s) in the table below.

| *a | Component with harness connected (Certification ECU (Smart Key ECU Assembly)) | - | - |
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Power Supply Condition | Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON | All OFF: Engine switch off (ACC and IG) ACC ON: Engine switch on (ACC) IG1 ON: Engine switch on (IG) (IG1 relay on) IG2 ON: Engine switch on (IG) (IG2 relay on) ST ON: Sending engine start request signal | Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time). |
Measure the voltage while checking the Data List on the intelligent tester.
| Tester Connection | Condition | Specified Condition |
| I78-6 (IG1D) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (ACC) | 1 V or less | |
| Engine switch on (IG) | 9 V or higher | |
| A43-9 (IG2D) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (ACC) | 1 V or less | |
| Engine switch on (IG) | 9 V or higher | |
| I78-4 (ACCD) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (IG) | 8.5 V or higher | |
| Engine switch on (ACC) | 8.5 V or higher |
|
| ||||
| OK | ||
| ||
| 8.READ VALUE USING INTELLIGENT TESTER |
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Start Switch1 | Engine switch 1 status/ON or OFF | ON: Engine switch pressed OFF: Engine switch not pressed |
|
| Start Switch2 | Engine switch 2 status/ON or OFF | ON: Engine switch pressed OFF: Engine switch not pressed |
|
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 9.INSPECT ENGINE SWITCH |
Inspect the engine switch (for 2AR-FE) (Click here).
Inspect the engine switch (for 2GR-FE) (Click here).
Inspect the engine switch (for 6AR-FSE) (Click here).
| Result | Proceed to |
| OK | A |
| NG (for 2AR-FE) | B |
| NG (for 2GR-FE) | C |
| NG (for 6AR-FSE) | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH) |
Disconnect the I78 connector from the certification ECU (smart key ECU assembly).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I78-28 (SSW1) - I58-5 (SS1) | Always | Below 1 Ω |
| I78-30 (SSW2) - I58-1 (SS2) | Always | Below 1 Ω |
| I78-28 (SSW1) or I58-5 (SS1) - Body ground | Always | 10 kΩ or higher |
| I78-30 (SSW2) or I58-1 (SS2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY) |
Disconnect the A43 certification ECU (smart key ECU assembly) connector.
Disconnect the A77 stop light switch assembly connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A77-1 (B) - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A43-18 (STP1) - A77-2 (OUT) | Always | Below 1 Ω |
| A43-18 (STP1) or A77-2 (OUT) - Body ground | Always | 10 kΩ or higher |
| A77-3 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Stop Light Switch Assembly) |
|
| ||||
| OK | |
| 12.INSPECT STOP LIGHT SWITCH ASSEMBLY |
Inspect the stop light switch assembly (Click here).
|
| ||||
| OK | ||
| ||
| 13.CHECK FOR DTC |
Enter the following menus:
for Entry & Start: Body / Entry & Start / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
The following DTCs are not output:
| A |
| DTC B2784 is output. | B |
| DTC B278A is output. | C |
|
| ||||
|
| ||||
| A | ||
| ||