ENGINE > ON-VEHICLE INSPECTION |
| 1. INSPECT ENGINE COOLANT |
| 2. INSPECT ENGINE OIL |
| 3. INSPECT BATTERY |
| 4. INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Remove the air cleaner filter element sub-assembly.
Visually check that the air cleaner filter is not excessively damaged or oily. If necessary, replace the air cleaner filter.
Install the air cleaner filter element sub-assembly.
| 5. INSPECT V-RIBBED BELT |
| 6. INSPECT V-RIBBED BELT TENSIONER ASSEMBLY |
Remove the V-ribbed belt (Click here).
Check that nothing is caught in the tensioner by turning it clockwise and counterclockwise. If a malfunction exists, replace the tensioner.
Install the V-ribbed belt (Click here).
| 7. INSPECT SPARK PLUG |
| 8. INSPECT VALVE LASH ADJUSTER NOISE |
Rev up the engine several times. Check that the engine does not emit unusual noises.
If unusual noises occur, warm up the engine and idle it for over 30 minutes. Then perform the preceding inspection.
| 9. INSPECT IGNITION TIMING |
Warm up and stop the engine.
When using the intelligent tester:
Check the ignition timing.
Connect the intelligent tester to the DLC3.
Start the engine and run it at idle.
Turn the intelligent tester main switch on.
Enter the following menus: Powertrain / Engine / Data List / IGN Advance.
Check that the ignition timing advances immediately when the engine speed is increased.
Enter the following menus: Powertrain / Engine / Active Test / Connect the TC and TE1.
Monitor IGN Advance.
Perform the Active Test.
When not using the intelligent tester:
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
| *1 | DLC3 |
Remove the V-bank cover sub-assembly .
Connect the timing light tester probe to the ignition coil wire for No. 1 cylinder.
Check the ignition timing at idle.
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
Check the ignition timing at idle.
Confirm that the ignition timing advances immediately when the engine rpm is increased.
Remove the timing light from the engine.
Install the V-bank cover sub-assembly .
| 10. INSPECT ENGINE IDLE SPEED |
Warm up and stop the engine.
When using the intelligent tester:
Check the idle speed.
Connect the intelligent tester to the DLC3.
Start the engine and run it at idle.
Turn the intelligent tester main switch on.
Enter the following menus: Powertrain / Engine / Data List / Engine Speed.
Read the value displayed on the tester.
When not using the intelligent tester:
![]() |
Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.
| *1 | DLC3 |
Check the idle speed.
| 11. INSPECT COMPRESSION |
Warm up and stop the engine.
Remove the 6 spark plugs (Click here).
![]() |
Check the cylinder compression pressure.
Insert a compression gauge into the spark plug hole.
While cranking the engine, measure the compression pressure.
If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect again.
Install the 6 spark plugs (Click here).
| 12. INSPECT CO/HC |
Start the engine.
Keep the engine speed at 2500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idle.
Immediately check CO/HC concentration during idle and when running at 2500 rpm.
Check the DTCs (Click here).
See the table below for possible causes, then inspect and correct the applicable causes if necessary.
| CO | HC | Problem | Cause |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (Fluctuating HC reading) |
|
| High | High | Rough idle (Black smoke from exhaust) |
|