Home › Drivetrain · U761E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P079112    Intermediate Shaft Speed Sensor "A" Circuit Short to Battery

DTC    P079114    Intermediate Shaft Speed Sensor "A" Circuit Short to Ground or Open

DTC    P079131    Intermediate Shaft Speed Sensor "A" No Signal

for Preparation Click here


DESCRIPTION

The output speed sensor NC detects the rotation speed of the counter gear, which indicates the intermediate shaft revolution (speed) of the transaxle. By comparing the input speed sensor NT signal with the output speed sensor NC signal, the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, thus, providing smooth gear shifts.

C316324E01


Text in Illustration 
*1
Counter Gear
*2
Clutch Drum
*3
Output Speed Sensor NC
*4
Input Speed Sensor NT

DTC No.
DTC Detection Condition
Trouble Area
P079112
1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
  1. The battery voltage is 8 V or more, the engine switch is on (IG) and the starter is off.
  2. The speed sensor input voltage is more than 1.9 V.
  3. 2 seconds
  4. 1-trip detection logic
  1. Wiring harness connector
  2. Transmission revolution sensor (Output speed sensor NC)
  3. Transmission wire
  4. ECM
P079114
1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
  1. The battery voltage is 8 V or more, the engine switch is on (IG) and the starter is off.
  2. The speed sensor input voltage is less than 0.1 V.
  3. 2 seconds
  4. 1-trip detection logic
  1. Wiring harness connector
  2. Transmission revolution sensor (Output speed sensor NC)
  3. Transmission wire
  4. ECM
P079131
1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
  1. The vehicle is being driven with the shift lever in D and the vehicle speed is 25 km/h (16 mph) or more.
  2. The speed indicated by the output speed sensor NC is less than 300 rpm.
  3. 2 seconds
  4. 1-trip detection logic
  1. Wiring harness connector
  2. Transmission revolution sensor (Output speed sensor NC)
  3. Transmission wire
  4. ECM

MONITOR DESCRIPTION

The NT terminal of the ECM detects a revolution signal from the input speed sensor NT (input RPM). The ECM calculates gear shifts by comparing the input speed sensor NT signal to the output speed sensor NC signal.
While the vehicle is being driven in 2nd, 3rd, 4th or 5th gear with the shift lever in D, if the input shaft revolution is less than 300 rpm*1 although the output shaft revolution is more than 1000 rpm*2, the ECM interprets this as a malfunction, illuminates the MIL and stores a DTC.
*1: Pulse is not output or is irregularly output.
*2: The vehicle speed is 50 km/h (31 mph) or more.

WIRING DIAGRAM


C314404E02


INSPECTION PROCEDURE

NOTICE:
Perform registration and/or initialization when parts related to the automatic transaxle are replaced (Click here).

HINT:
  1. Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
  2. After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
    1. Perform the D Position Shift Test inspection in Road Test and drive the vehicle for 2 seconds or more at 25 km/h (16 mph) or more (Click here).
    2. Check for DTCs again (Click here).


DATA LIST
  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the engine switch on (IG).

  5. Turn the GTS on.

  6. Enter the following menus: Powertrain / Transmission / Data List.

  7. Read the Data List according to the display on the GTS.

    Transmission 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    NC Sensor Speed
    Counter Gear Speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    -
    Data is displayed in increments of 50 rpm

    HINT:
    1. NC Speed Sensor is always 0 while driving: Open or short in the sensor or circuit.
    2. NC Speed Sensor is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor malfunction, improper installation, or intermittent connection malfunction in the circuit.

1.INSPECT TRANSMISSION REVOLUTION SENSOR (SPEED SENSOR INSTALLATION)
  1. Remove the transmission valve body assembly.



    C133219
  1. Make sure that the connector is properly connected, and check the transmission revolution sensor installation (Click here).

OK:
The installation bolts are tightened properly and there is no clearance between the sensor and transmission valve body assembly.



NG
REPAIR OR REPLACE TRANSMISSION REVOLUTION SENSOR (Click here)
OK


2.INSPECT TRANSMISSION WIRE


    C189545E14
  1. Disconnect the transmission revolution sensor connector from the transmission wire.
    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)
    *b
    Wiring harness connector side
    *c
    Transmission revolution sensor side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (NCO) sensor side - A-3 (NCO) wiring harness connector side
    Always
    Below 1 Ω
    4 (NCB) sensor side - A-4 (NCB) wiring harness connector side
    Always
    Below 1 Ω
    3 (NCO) sensor side - Body ground and other terminals
    Always
    10 kΩ or higher
    4 (NCB) sensor side - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPLACE TRANSMISSION WIRE (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
  1. Disconnect the E96 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E96-73 (NCB) - E8-4 (NCB)
    Always
    Below 1 Ω
    E96-74 (NCO) - E8-3 (NCO)
    Always
    Below 1 Ω
    E96-73 (NCB) or E8-4 (NCB)- Body ground and other terminals
    Always
    10 kΩ or higher
    E96-74 (NCO) or E8-3 (NCO) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT WIRING HARNESS CONNECTOR
  1. Remove the wiring harness connector.



  1. Measure the resistance according to the value(s) in the table below.


    C267935E02


    Text in Illustration 
    *1
    Wiring Harness Connector
    -
    -
    *a
    Transmission wire side
    *b
    ECM side

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E8-3 (NCO) - A-3 (NCO)
    Always
    Below 1 Ω
    E8-4 (NCB) - A-4 (NCB)
    Always
    Below 1 Ω
    E8-3 (NCO) - All other terminals
    Always
    10 kΩ or higher
    E8-4 (NCB) - All other terminals
    Always
    10 kΩ or higher



NG
REPLACE WIRING HARNESS CONNECTOR (Click here)
OK


5.REPLACE TRANSMISSION REVOLUTION SENSOR
  1. Replace the transmission revolution sensor (Click here).


NEXT


6.CHECK IF DTC OUTPUT RECURS (DTC P079112, P079114 AND/OR P079131)
  1. Connect the GTS to the DLC3.

  1. Start the engine and turn the GTS on.

  1. Clear the DTCs (Click here).

    HINT:
    Write down the currently output DTCs before clearing them.

  1. Perform the monitor drive pattern (Click here).

  1. Enter the following menus: Powertrain / Transmission / Trouble Codes.

  1. Read the DTCs using the GTS.

    Result:
    Result
    Proceed to
    DTC P079112, P079114 and/or P079131 is output
    A
    DTCs are not output
    B



B
END
A

REPLACE ECM (Click here)