Home › Vehicle Interior › HEATING / AIR CONDITIONING › CONDENSER

CONDENSER > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM
  1. Turn the A/C switch on.

  1. Operate the air conditioning with a set temperature of 25°C (77°F) and the blower at low for 10 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the air conditioning system to collect in the air conditioning compressor.

  1. Turn the ignition switch off.

  1. Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



4. REMOVE FRONT BUMPER ASSEMBLY (for TMC, TMMR Made)
(Click here)


5. REMOVE FRONT BUMPER ASSEMBLY (for TMMK Made)
(Click here)


6. REMOVE BATTERY (for 2GR-FE)


7. REMOVE INLET AIR CLEANER ASSEMBLY (for 2AR-FE)


    A255404
  1. Remove the 2 bolts and inlet air cleaner assembly.



8. REMOVE INLET AIR CLEANER ASSEMBLY (for 6AR-FSE)


    A338524
  1. Remove the 2 bolts and inlet air cleaner assembly.



9. REMOVE INLET NO. 2 AIR CLEANER (for 2GR-FE)


    A255421
  1. Disconnect the 2 wire harness clamps and vacuum hose clamp.

  1. Remove the 2 bolts and inlet No. 2 air cleaner.



10. REMOVE INLET NO. 1 AIR CLEANER (for 2GR-FE)


    A256225
  1. Disengage the pin and remove the inlet No. 1 air cleaner.



11. REMOVE HOOD LOCK ASSEMBLY (for TMC, TMMR Made)
for LHD:
for RHD:


12. REMOVE HOOD LOCK ASSEMBLY (for TMMK Made)


    B382415E01
  1. Using a screwdriver, remove the hood lock nut cap.
    Text in Illustration 
    *a
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



  1. w/ Engine Hood Courtesy Switch:



      B381594
    1. Disconnect the connector.



    B380676E01
  1. Remove the 2 bolts and hood lock bolt.
    Text in Illustration 
    *1
    Hood Lock Bolt



    B380677
  1. Disconnect the hood lock control cable assembly and remove the hood lock assembly.



13. REMOVE UPPER RADIATOR SUPPORT (for 2AR-FE)


    A263146
  1. Disconnect the 2 horn connectors.



    A264524E02
  1. Disengage the clamp and disconnect the hood lock control cable assembly from the upper radiator support.
    Text in Illustration 
    *A
    for RHD
    *B
    for LHD

  1. Remove the 5 bolts and upper radiator support.

  1. Remove the 2 radiator support cushions from the radiator assembly.



14. REMOVE UPPER RADIATOR SUPPORT (for 2GR-FE)


    A263146
  1. Disconnect the 2 connectors.



    A265982
  1. Disconnect the hood lock control cable clamp and remove the 5 bolts and upper radiator support.

  1. Remove the 2 radiator support cushions from the radiator assembly.



15. REMOVE UPPER RADIATOR SUPPORT (for 6AR-FSE)


    A263146
  1. Disconnect the 2 horn connectors.



    A269572
  1. Disengage the clamp and disconnect the hood lock control cable assembly from the upper radiator support.

  1. Remove the 5 bolts and upper radiator support.

  1. Remove the 2 radiator support cushions from the radiator assembly.



16. REMOVE RADIATOR SIDE DEFLECTOR LH (for TMC, TMMR Made)


    E301547
  1. Disengage the 3 claws and guide, and remove the radiator side deflector LH.



17. REMOVE RADIATOR SIDE DEFLECTOR LH (for TMMK Made)


    E300711
  1. Disengage the 3 claws and guide, and remove the radiator side deflector LH.



18. REMOVE RADIATOR SIDE DEFLECTOR RH (for TMC, TMMR Made)


    E301548
  1. Disengage the 3 claws and guide, and remove the radiator side deflector RH.



19. REMOVE RADIATOR SIDE DEFLECTOR RH (for TMMK Made)


    E300712
  1. Disengage the 3 claws and guide, and remove the radiator side deflector RH.



20. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE


    E301549
  1. Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose from the cooler condenser assembly.

  1. Remove the O-ring from the No. 1 cooler refrigerant discharge hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



21. DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY


    E301550
  1. Remove the bolt and disconnect the air conditioner tube and accessory assembly from the cooler condenser assembly.

  1. Remove the O-ring from the air conditioner tube and accessory assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



22. REMOVE COOLER CONDENSER ASSEMBLY


    E301551
  1. Remove the 4 bolts.



    E301552
  1. Disengage the 2 guides and remove the cooler condenser assembly as shown in the illustration.