Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on 4 Windows)

DTC    B2312    Power Window Switch Malfunction

for Preparation Click here


DESCRIPTION

The power window regulator motor assemblies are operated by the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assemblies. The power window regulator motor assemblies have motor, regulator and ECU functions.
This DTC is output when the ECU built into a power window regulator motor assembly and multiplex network master switch assembly determine that the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly is stuck.

Master Switch (Multiplex Network Master Switch Assembly) 
DTC No.
DTC Detection Condition
Trouble Area
B2312
  1. Multiplex network master switch assembly stuck
  2. Multiplex network master switch assembly held in same position for more than 20 seconds
  3. Door control switch (multiplex network master switch assembly) operated for 20 seconds or more
Multiplex network master switch assembly

D-Door Motor (Power Window Regulator Motor Assembly (for Driver Door)) 
DTC No.
DTC Detection Condition
Trouble Area
B2312
  1. Multiplex network master switch assembly stuck
  2. Multiplex network master switch assembly held in same position for more than 20 seconds
  1. Multiplex network master switch assembly
  2. Power window regulator motor assembly (for driver door)
  3. Wire harness or connector

P-Door Motor (Power Window Regulator Motor Assembly (for Front Passenger Door)) 
DTC No.
DTC Detection Condition
Trouble Area
B2312
  1. Power window regulator switch assembly stuck
  2. Power window regulator switch assembly held in same position for more than 20 seconds
  1. Power window regulator switch assembly
  2. Power window regulator motor assembly (for front passenger door)
  3. Wire harness or connector

RL-Door Motor (Power Window Regulator Motor Assembly (for Rear LH Door)) 
DTC No.
DTC Detection Condition
Trouble Area
B2312
  1. Rear power window regulator switch assembly (for LH door) stuck
  2. Power window regulator switch assembly held in same position for more than 20 seconds
  1. Rear power window regulator switch assembly (for LH door)
  2. Power window regulator motor assembly (for rear LH door)
  3. Wire harness or connector

RR-Door Motor (Power Window Regulator Motor Assembly (for Rear RH Door)) 
DTC No.
DTC Detection Condition
Trouble Area
B2312
  1. Rear power window regulator switch assembly (for RH door) stuck
  2. Power window regulator switch assembly held in same position for more than 20 seconds
  1. Rear power window regulator switch assembly (for RH door)
  2. Power window regulator motor assembly (for rear RH door)
  3. Wire harness or connector

WIRING DIAGRAM


for Driver Door

B234587E06


for Front Passenger Door

B203371E99


for Rear LH Door

B286840E01


for Rear RH Door

B286840E02


INSPECTION PROCEDURE

HINT:
If DTC B2312 is not output again after the DTC has been cleared, the DTC was output due to the switch being held.

NOTICE:
  1. DTC B2312 can be stored in the multiplex network master switch assembly and in each power window regulator motor assembly (power window ECU).
  2. If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system (Click here).

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2312 is not output.



NG
Go to step 2
OK

END (DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE) 

2.CHECK DTC OUTPUT
  1. Check the parts which the DTCs have been output from.

    Result:
    Result
    Proceed to
    DTC output from multiplex network master switch assembly
    A
    DTC output from power window regulator motor assembly (for driver door)
    B
    DTC output from power window regulator motor assembly (for front passenger door)
    C
    DTC output from power window regulator motor assembly (for rear LH door)
    D
    DTC output from power window regulator motor assembly (for rear RH door)
    E



B
Go to step 3

C
Go to step 7

D
Go to step 10

E
Go to step 13
A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (Click here)  

3.READ VALUE USING INTELLIGENT TESTER (D-DOOR MOTOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / D-Door Motor / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    D-Door Motor (Power Window Regulator Motor Assembly (for Driver Door) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Up SW
    Driver door power window manual up switch signal / ON or OFF
    ON: Driver door power window manual up switch operated
    OFF: Driver door power window manual up switch not operated
    -
    D Door P/W Down SW
    Driver door power window manual down switch signal / ON or OFF
    ON: Driver door power window manual down switch operated
    OFF: Driver door power window manual down switch not operated
    -

    OK:
    On the intelligent tester screen, ON or OFF is displayed accordingly.



NG
Go to step 4
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) (Click here)  

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR))
  1. Disconnect the multiplex network master switch assembly connector.

  1. Disconnect the power window regulator motor assembly (for driver door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    K3-20 (UP) - Body ground
    Always
    10 kΩ or higher
    K3-15 (DOWN) - Body ground
    Always
    10 kΩ or higher
    K9-10 (UP) - Body ground
    Always
    10 kΩ or higher
    K9-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    J3-20 (UP) - Body ground
    Always
    10 kΩ or higher
    J3-15 (DOWN) - Body ground
    Always
    10 kΩ or higher
    J9-10 (UP) - Body ground
    Always
    10 kΩ or higher
    J9-7 (DOWN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
  1. Replace the multiplex network master switch assembly (Click here).


NEXT


6.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2312 is not output.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) (Click here)
OK

END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WAS DEFECTIVE) 

7.READ VALUE USING INTELLIGENT TESTER (P-DOOR MOTOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / P-Door Motor / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    P-Door Motor (Power Window Regulator Motor Assembly (for Front Passenger Door)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Auto SW
    Front passenger door power window auto switch signal / ON or OFF
    ON: Front passenger door power window auto switch operated
    OFF: Front passenger door power window auto switch not operated
    -
    P Door P/W Up SW
    Front passenger door power window manual up switch signal / ON or OFF
    ON: Front passenger door power window manual up switch operated
    OFF: Front passenger door power window manual up switch not operated
    -
    P Door P/W Down SW
    Front passenger door power window manual down switch signal / ON or OFF
    ON: Front passenger door power window manual down switch operated
    OFF: Front passenger door power window manual down switch not operated
    -

    OK:
    On the intelligent tester screen, ON or OFF is displayed accordingly.



NG
Go to step 8
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) (Click here)  

8.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY


    B203473E29
  1. Remove the power window regulator switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (UP) - 1 (GND)
    Auto up or up position
    Below 1 Ω
    7 (DOWN) - 1 (GND)
    Auto down or down position
    Below 1 Ω
    8 (AUTO) - 1 (GND)
    Auto up or auto down position
    Below 1 Ω
    6 (UP) - 1 (GND)
    Free
    10 kΩ or higher
    7 (DOWN) - 1 (GND)
    Free
    10 kΩ or higher
    8 (AUTO) - 1 (GND)
    Free
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Power Window Regulator Switch Assembly)



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - POWER WINDOW REGULATOR MOTOR (FOR FRONT PASSENGER DOOR))
  1. Disconnect the power window regulator motor assembly (for front passenger door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    J4-6 (UP) - Body ground
    Always
    10 kΩ or higher
    J4-8 (AUTO) - Body ground
    Always
    10 kΩ or higher
    J4-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    J9-10 (UP) - Body ground
    Always
    10 kΩ or higher
    J9-4 (AUTO) - Body ground
    Always
    10 kΩ or higher
    J9-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    K4-6 (UP) - Body ground
    Always
    10 kΩ or higher
    K4-8 (AUTO) - Body ground
    Always
    10 kΩ or higher
    K4-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    K9-10 (UP) - Body ground
    Always
    10 kΩ or higher
    K9-4 (AUTO) - Body ground
    Always
    10 kΩ or higher
    K9-7 (DOWN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) (Click here)  

10.READ VALUE USING INTELLIGENT TESTER (RL-DOOR MOTOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / RL-Door Motor / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    RL-Door Motor (Power Window Regulator Motor Assembly (for Rear LH Door)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RL Door P/W Auto SW
    Rear LH door power window auto switch signal / ON or OFF
    ON: Rear LH door power window auto switch operated
    OFF: Rear LH door power window auto switch not operated
    -
    RL Door P/W Up SW
    Rear LH door power window manual up switch signal / ON or OFF
    ON: Rear LH door power window manual up switch operated
    OFF: Rear LH door power window manual up switch not operated
    -
    RL Door P/W Down SW
    Rear LH door power window manual down switch signal / ON or OFF
    ON: Rear LH door power window manual down switch operated
    OFF: Rear LH door power window manual down switch not operated
    -

    OK:
    On the intelligent tester screen, ON or OFF is displayed accordingly.



NG
Go to step 11
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR) (Click here)  

11.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR LH DOOR)


    B203473E29
  1. Remove the rear power window regulator switch assembly (for LH door) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (UP) - 1 (GND)
    Auto up or up position
    Below 1 Ω
    7 (DOWN) - 1 (GND)
    Auto down or down position
    Below 1 Ω
    8 (AUTO) - 1 (GND)
    Auto up or auto down position
    Below 1 Ω
    6 (UP) - 1 (GND)
    Free
    10 kΩ or higher
    7 (DOWN) - 1 (GND)
    Free
    10 kΩ or higher
    8 (AUTO) - 1 (GND)
    Free
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Power Window Regulator Switch Assembly (for LH Door))



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR LH DOOR) (Click here)
OK


12.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH (FOR LH DOOR) - WINDOW REGULATOR MOTOR (FOR REAR LH DOOR))
  1. Disconnect the power window regulator motor assembly (for rear LH door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M4-6 (UP) - Body ground
    Always
    10 kΩ or higher
    M4-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    M4-8 (AUTO) - Body ground
    Always
    10 kΩ or higher
    M2-10 (UP) - Body ground
    Always
    10 kΩ or higher
    M2-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    M2-4 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR) (Click here)  

13.READ VALUE USING INTELLIGENT TESTER (RR-DOOR MOTOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / RR-Door Motor / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    RR-Door Motor (Power Window Regulator Motor Assembly (for Rear RH Door)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Door P/W Auto SW
    Rear RH door power window auto switch signal / ON or OFF
    ON: Rear RH door power window auto switch operated
    OFF: Rear RH door power window auto switch not operated
    -
    RR Door P/W Up SW
    Rear RH door power window manual up switch signal / ON or OFF
    ON: Rear RH door power window manual up switch operated
    OFF: Rear RH door power window manual up switch not operated
    -
    RR Door P/W Down SW
    Rear RH door power window manual down switch signal / ON or OFF
    ON: Rear RH door power window manual down switch operated
    OFF: Rear RH door power window manual down switch not operated
    -

    OK:
    On the intelligent tester screen, ON or OFF is displayed accordingly.



NG
Go to step 14
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR) (Click here)  

14.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR)


    B203473E29
  1. Remove the rear power window regulator switch assembly (for RH door) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (UP) - 1 (GND)
    Auto up or up position
    Below 1 Ω
    7 (DOWN) - 1 (GND)
    Auto down or down position
    Below 1 Ω
    8 (AUTO) - 1 (GND)
    Auto up or auto down position
    Below 1 Ω
    6 (UP) - 1 (GND)
    Free
    10 kΩ or higher
    7 (DOWN) - 1 (GND)
    Free
    10 kΩ or higher
    8 (AUTO) - 1 (GND)
    Free
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Power Window Regulator Switch Assembly (for RH Door))



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR) (Click here)
OK


15.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH (FOR RH DOOR) - WINDOW REGULATOR MOTOR (FOR REAR RH DOOR))
  1. Disconnect the power window regulator motor assembly (for rear RH door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L4-6 (UP) - Body ground
    Always
    10 kΩ or higher
    L4-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    L4-8 (AUTO) - Body ground
    Always
    10 kΩ or higher
    L2-10 (UP) - Body ground
    Always
    10 kΩ or higher
    L2-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    L2-4 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR) (Click here)