DTC B2311 Power Window Motor Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| B2311 |
|
|
| DTC No. | DTC Detection Condition | Trouble Area |
| B2311 |
|
|
| 1.CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
|
| ||||
| OK | ||
| ||
| 2.CHECK DTC OUTPUT |
Check the parts which the DTCs have been output from.
| Result | Proceed to |
| DTC output from power window regulator motor assembly (for driver door) | A |
| DTC output from power window regulator motor assembly (for front passenger door) | B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) - BATTERY AND BODY GROUND) |
![]() |
Disconnect the K9 power window regulator motor assembly (for driver door) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K9-2 (B) - K9-1 (GND) | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K9-1 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Power Window Regulator Motor Assembly) |
|
| ||||
|
| ||||
| 4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR) - BATTERY AND BODY GROUND) |
![]() |
Disconnect the J9 power window regulator motor assembly (for front passenger door) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J9-2 (B) - J9-1 (GND) | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J9-1 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Power Window Regulator Motor Assembly) |
|
| ||||
| OK | |
| 5.PERFORM ACTIVE TEST USING GTS (APPLICABLE LOCATION) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / (desired system) / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Power Window | Power window | OFF / DOWN / UP | - |
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Power Window | Power window | OFF / DOWN / UP | - |
| Result | Proceed to |
| OK | A |
| NG (Driver door power window) | B |
| NG (Front passenger door power window) |
|
| ||||
| A | |
| 6.PERFORM INITIALIZATION (APPLICABLE LOCATION) |
Initialize the power window regulator motor assembly (Click here).
| NEXT | |
| 7.CHECK POWER WINDOW CONTROL SYSTEM (APPLICABLE LOCATION) |
Check that the power window operates normally by opening and closing the window (Click here).
| Result | Proceed to |
| OK | A |
| NG (Driver door power window) | B |
| NG (Front passenger door power window) |
|
| ||||
| A | |
| 8.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY |
Check that the power window components are installed correctly.
|
| ||||
| OK | |
| 9.CHECK DTC OUTPUT |
Turn the engine switch off.
Wait for at least 10 seconds, and then turn the engine switch on (IG).
Check for DTCs (Click here).
| Result | Proceed to |
| OK | A |
| NG (Driver door power window) | B |
| NG (Front passenger door power window) |
|
| ||||
| A | ||
| ||