Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

AUDIO AND VISUAL SYSTEM (for Radio and Display Type) > Microphone Circuit between Microphone and Radio Receiver

for Preparation Click here


DESCRIPTION

The radio and display receiver assembly and roof console box assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
Using this circuit, the radio and display receiver assembly sends power to the roof console box assembly (telephone microphone assembly), and the roof console box assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.

WIRING DIAGRAM


E268499E07


INSPECTION PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)


    E277821
  1. Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check (Click here).

  1. When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

    OK:
    Check result is normal.



NG
Go to step 2
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)  

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the I155 radio and display receiver assembly connector.

  1. Disconnect the S12 roof console box assembly (telephone microphone assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-4 (MACC) - S12-14 (MACC)
    Always
    Below 1 Ω
    I155-5 (MIN+) - S12-13 (MCO+)
    Always
    Below 1 Ω
    I155-19 (MIN-) - S12-12 (MCO-)
    Always
    Below 1 Ω
    I155-6 (SNS2) - S12-15 (SNS2)
    Always
    Below 1 Ω
    I155-4 (MACC) - Body ground
    Always
    10 kΩ or higher
    I155-5 (MIN+) - Body ground
    Always
    10 kΩ or higher
    I155-19 (MIN-) - Body ground
    Always
    10 kΩ or higher
    I155-18 (SGND) - Body ground
    Always
    10 kΩ or higher
    I155-6 (SNS2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY


    E291452E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I155-4 (MACC) - Body ground
    Ignition switch ACC
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-18 (SGND) - Body ground
    Always
    Below 1 Ω
    I155-19 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


4.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
  1. Remove the roof console box assembly (telephone microphone assembly) (Click here).



    E187117E51
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    15 (SNS2) - 12 (MCO-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Roof Console Box Assembly (Telephone Microphone Assembly))



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (Click here)
OK


5.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
  1. Turn the ignition switch to ACC.



    E187122E45
  1. Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the S12 roof console box assembly (telephone microphone assembly) connector.

  1. Check the waveform of the roof console box assembly (telephone microphone assembly) using the oscilloscope.

    Result:
    Result
    Proceed to
    A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is output.
    A
    A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is not output.
    B

    Text in Illustration 
    *a
    Component with harness connected
    (Roof Console Box Assembly (Telephone Microphone Assembly))



B
REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)