Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

DTC    B1500    Fuel Sender Open Detected

for Preparation Click here


DESCRIPTION

This DTC is stored when the combination meter assembly detects a fuel sender gauge malfunction via a direct line.

DTC No.
DTC Detection Condition
Trouble Area
B1500
When IG voltage is 9.5 V or more and the following condition is detected:
  1. Fuel sender gauge operation malfunction
  1. Harness or connector
  2. Fuel sender gauge assembly
  3. Combination meter assembly

WIRING DIAGRAM


E230580E14


INSPECTION PROCEDURE

1.READ VALUE USING GTS (FUEL INPUT)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Combination Meter / Data List.

  1. Read the Data List according to the display on the GTS.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Input*1
    Fuel input/Min.: 0, Max.: 127.5
    Fuel receiver gauge indicates F: 62.9
    Unit: Liter
    Fuel receiver gauge indicates 3/4: 54.4
    Fuel receiver gauge indicates 1/2: 35.0
    Fuel receiver gauge indicates 1/4: 15.4
    Fuel receiver gauge indicates E: 7.0
    Fuel Input*2
    Fuel input/Min.: 0, Max.: 127.5
    Fuel receiver gauge indicates F: 57.9
    Unit: Liter
    Fuel receiver gauge indicates 3/4: 45.6
    Fuel receiver gauge indicates 1/2: 32.2
    Fuel receiver gauge indicates 1/4: 18.9
    Fuel receiver gauge indicates E: 6.4

    1. *1: except TMMK Made
    2. *2: for TMMK Made

    Result:

    Result
    Proceed to
    Fuel level data can be displayed on the GTS and DTC B1500 is output.
    A
    Fuel level data cannot be displayed on the GTS.
    B



B
Go to step 2
A

REPLACE COMBINATION METER ASSEMBLY (Click here)  

2.INSPECT FUEL SENDER GAUGE ASSEMBLY


    E224284E39
  1. Disconnect the I18 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I18-14 (FR) - I18-15 (FE)
    Always
    13.5 to 414.5 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)



NG
Go to step 3
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
  1. Disconnect the N11 fuel suction tube assembly with pump and gauge connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I18-14 (FR) - N11-2 (FS)
    Always
    Below 1 Ω
    I18-14 (FR) - Body ground
    Always
    10 kΩ or higher
    I18-15 (FE) - N11-3 (FE)
    Always
    Below 1 Ω
    I18-15 (FE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FUEL SENDER GAUGE ASSEMBLY
  1. Remove the fuel sender gauge assembly (Click here for 2AR-FE (except TMMK Made), Click here for 2AR-FE (for TMMK Made), Click here for 2GR-FE, Click here for 6AR-FSE).

  1. Inspect the fuel sender gauge assembly (Click here for 2AR-FE (except TMMK Made), Click here for 2AR-FE (for TMMK Made), Click here for 2GR-FE, Click here for 6AR-FSE).

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2AR-FE) (except TMMK Made)
    B
    NG (for 2AR-FE) (for TMMK Made)
    C
    NG (for 2GR-FE)
    D
    NG (for 6AR-FSE)
    E



B
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

C
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

D
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)

E
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)