Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM

DTC    C1AB4    Open in Outer Mirror Indicator(Master)

for Preparation Click here


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects an open in the outer rear view mirror indicator RH.

DTC No.
DTC Detection Condition
Trouble Area
C1AB4
When either of the following conditions is met:
  1. Blind spot monitor main switch (warning canceling switch assembly) is on.
  1. The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator.
  1. Outer rear view mirror RH (outer rear view mirror indicator RH)
  2. Outer rear view mirror assembly RH
  3. Wire harness or connector
  4. Blind spot monitor sensor RH
  5. Outer mirror control ECU assembly RH

WIRING DIAGRAM


E233743E35


INSPECTION PROCEDURE

NOTICE:
When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.

1.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH, BODY GROUND - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
  1. Disconnect the O43 blind spot monitor sensor RH connector.

  1. Disconnect the J10 outer mirror control ECU assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O43-4 (OMIR) - J10-10 (BDSR)
    Always
    Below 1 Ω
    J10-7 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH
  1. Disconnect the z17 outer mirror control ECU assembly RH connector.



    E233744E50
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J10-10 (BDSR) - z17-7 (BSM+)
    Always
    Below 1 Ω
    J10-7 (GND) - z17-12 (BSM-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Outer Mirror Control ECU Assembly RH)



NG
REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH))
  1. Disconnect the IND2 outer rear view mirror RH (outer rear view mirror indicator RH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z17-7 (BSM+) - IND2-1 (+)
    Always
    Below 1 Ω
    z17-12 (BSM-) - IND2-2 (-)
    Always
    Below 1 Ω



NG
REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH (Click here)
OK


5.INSPECT OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)
  1. Remove the outer rear view mirror RH (outer rear view mirror indicator RH) (Click here).

  1. Inspect the outer rear view mirror indicator RH on the outer rear view mirror RH (Click here).



NG
REPLACE OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)) (Click here)
OK


6.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
REPLACE BLIND SPOT MONITOR SENSOR RH (Click here)
OK

END (OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH) WAS DEFECTIVE)