Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM

DTC    C1AB5    Open in Outer Mirror Indicator(Slave)

for Preparation Click here


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects an open in the outer rear view mirror indicator LH.

DTC No.
DTC Detection Condition
Trouble Area
C1AB5
When either of the following conditions is met:
  1. Blind spot monitor main switch (warning canceling switch assembly) is on.
  1. The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator.
  1. Outer rear view mirror LH (outer rear view mirror indicator LH)
  2. Outer rear view mirror assembly LH
  3. Wire harness or connector
  4. Blind spot monitor sensor LH
  5. Outer mirror control ECU assembly LH

WIRING DIAGRAM


E233743E36


INSPECTION PROCEDURE

NOTICE:
When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.

1.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH, BODY GROUND - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
  1. Disconnect the T17 blind spot monitor sensor LH connector.

  1. Disconnect the K12 outer mirror control ECU assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T17-4 (OMIL) - K12-10 (BDSL)
    Always
    Below 1 Ω
    K12-7 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH
  1. Disconnect the z18 outer mirror control ECU assembly LH connector.



    E233744E51
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K12-10 (BDSL) - z18-7 (BSM+)
    Always
    Below 1 Ω
    K12-7 (GND) - z18-12 (BSM-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Outer Mirror Control ECU Assembly LH)



NG
REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - OUTER REAR VIEW MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH))
  1. Disconnect the IND1 outer rear view mirror LH (outer rear view mirror indicator LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z18-7 (BSM+) - IND1-1 (+)
    Always
    Below 1 Ω
    z18-12 (BSM-) - IND1-2 (-)
    Always
    Below 1 Ω



NG
REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH (Click here)
OK


5.INSPECT OUTER REAR VIEW MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)
  1. Remove the outer rear view mirror LH (outer rear view mirror indicator LH) (Click here).

  1. Inspect the outer rear view mirror indicator LH on the outer rear view mirror LH (Click here).



NG
REPLACE OUTER REAR VIEW MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)) (Click here)
OK


6.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
REPLACE BLIND SPOT MONITOR SENSOR LH (Click here)
OK

END (OUTER REAR VIEW MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH) WAS DEFECTIVE)