Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type)

DTC    B15C3    Speaker Output Short

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No.
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit
  1. Harness or connector
  2. Speaker
  3. Navigation receiver assembly*1
  4. Stereo component amplifier assembly*2
  1. *1: for TMC Made
  2. *2: for TMMK Made

WIRING DIAGRAM


for TMC Made

E286971E06


for TMMK Made

E345601E01


E226483E18


INSPECTION PROCEDURE

1.CHECK MODEL
  1. Choose the model to be inspected.

    Result:
    Result
    Proceed to
    for TMC Made
    A
    for TMMK Made
    B



B
Go to step 7
A


2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BODY GROUND)
  1. Disconnect the I64 and I65 navigation receiver assembly connectors.

  1. Disconnect the I83 and I1 front No. 2 speaker assembly connectors.

  1. Disconnect the O18 and O21 rear speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I64-1 (FR+) or I83-4 (TWR+) - Body ground
    Always
    10 kΩ or higher
    I64-5 (FR-) or I83-2 (TWR-) - Body ground
    Always
    10 kΩ or higher
    I64-2 (FL+) or I1-4 (TWL+) - Body ground
    Always
    10 kΩ or higher
    I64-6 (FL-) or I1-2 (TWL-) - Body ground
    Always
    10 kΩ or higher
    I65-1 (RR+) or O18-1 - Body ground
    Always
    10 kΩ or higher
    I65-3 (RR-) or O18-2 - Body ground
    Always
    10 kΩ or higher
    I65-2 (RL+) or O21-1 - Body ground
    Always
    10 kΩ or higher
    I65-6 (RL-) or O21-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND)
  1. Disconnect the J5 and K5 front No. 1 speaker assembly connectors.

  1. Disconnect the I83 and I1 front No. 2 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I83-3 (+) or J5-1 - Body ground
    Always
    10 kΩ or higher
    I83-1 (-) or J5-2 - Body ground
    Always
    10 kΩ or higher
    I1-3 (+) or K5-1 - Body ground
    Always
    10 kΩ or higher
    I1-1 (-) or K5-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


5.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Remove the front No. 2 speaker assembly (Click here).

  1. Inspect the front No. 2 speaker assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check that no DTCs are output.

    OK:
    No DTCs are output.



NG
Go to step 6
OK

END 

6.INSPECT REAR SPEAKER ASSEMBLY
  1. Remove the rear speaker assembly (Click here).

  1. Inspect the rear speaker assembly (Click here).



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)  

7.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND)
  1. Disconnect the I68 stereo component amplifier assembly connector.

  1. Disconnect the J5 and K5 front No. 1 speaker assembly connectors.

  1. Disconnect the I84 and I2 front No. 2 speaker assembly connectors.

  1. Disconnect the I60 front No. 3 speaker assembly connector.

  1. Disconnect the O19 and O20 rear No. 2 speaker assembly connectors.

  1. Disconnect the O22 rear speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-15 (FR+) or J5-1 (+) - Body ground
    Always
    10 kΩ or higher
    I68-30 (FR-) or J5-2 (-) - Body ground
    Always
    10 kΩ or higher
    I68-11 (FL+) or K5-1 (+) - Body ground
    Always
    10 kΩ or higher
    I68-26 (FL-) or K5-2 (-) - Body ground
    Always
    10 kΩ or higher
    I68-12 (TWR+) or I84-4 - Body ground
    Always
    10 kΩ or higher
    I68-27 (TWR-) or I84-3 - Body ground
    Always
    10 kΩ or higher
    I68-14 (TWL+) or I2-4 - Body ground
    Always
    10 kΩ or higher
    I68-29 (TWL-) or I2-3 - Body ground
    Always
    10 kΩ or higher
    I68-13 (CTR+) or I60-2 - Body ground
    Always
    10 kΩ or higher
    I68-28 (CTR-) or I60-1 - Body ground
    Always
    10 kΩ or higher
    I68-10 (SR+) or O19-2 - Body ground
    Always
    10 kΩ or higher
    I68-25 (SR-) or O19-1 - Body ground
    Always
    10 kΩ or higher
    I68-9 (SL+) or O20-2 - Body ground
    Always
    10 kΩ or higher
    I68-24 (SL-) or O20-1 - Body ground
    Always
    10 kΩ or higher
    I68-8 (WF1+) or O22-1 - Body ground
    Always
    10 kΩ or higher
    I68-23 (WF1-) or O22-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


9.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Remove the front No. 2 speaker assembly (Click here).

  1. Inspect the front No. 2 speaker assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check that no DTCs are output.

    OK:
    No DTCs are output.



NG
Go to step 10
OK

END 

10.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY
  1. Remove the front No. 3 speaker assembly (Click here).

  1. Inspect the front No. 3 speaker assembly (Click here).



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)
OK


11.INSPECT REAR NO. 2 SPEAKER ASSEMBLY
  1. Remove the rear No. 2 speaker assembly (Click here).

  1. Inspect the rear No. 2 speaker assembly (Click here).



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)
OK


12.INSPECT REAR SPEAKER ASSEMBLY
  1. Remove the rear speaker assembly (Click here).

  1. Inspect the rear speaker assembly (Click here).



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)