Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

DTC    B15C3    Speaker Output Short

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No.
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit
  1. Harness or connector
  2. Speaker
  3. Telematics transceiver*
  4. Radio and display receiver assembly
  1. *: w/ Manual (SOS) Switch

WIRING DIAGRAM


E352439E02


INSPECTION PROCEDURE

NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System (w/ Manual (SOS) Switch) (Click here).

1.CONFIRM MODEL
  1. Choose the model to be inspected.

    Result:
    Result
    Proceed to
    w/o Manual (SOS) Switch
    A
    w/ Manual (SOS) Switch
    B



B
Go to step 4
A


2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY OR SPEAKERS - BODY GROUND)
  1. Disconnect the I152 and I153 radio and display receiver assembly connectors.

  1. Disconnect the I83 and I1 front No. 2 speaker assembly connectors.

  1. Disconnect the O18 and O21 rear speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I152-1 (FR+) or I83-4 (TWR+) - Body ground
    Always
    10 kΩ or higher
    I152-5 (FR-) or I83-2 (TWR-) - Body ground
    Always
    10 kΩ or higher
    I152-2 (FL+) or I1-4 (TWL+) - Body ground
    Always
    10 kΩ or higher
    I152-6 (FL-) or I1-2 (TWL-)- Body ground
    Always
    10 kΩ or higher
    I153-1 (RR+) or O18-1 - Body ground
    Always
    10 kΩ or higher
    I153-3 (RR-) or O18-2 - Body ground
    Always
    10 kΩ or higher
    I153-2 (RL+) or O21-1 - Body ground
    Always
    10 kΩ or higher
    I153-6 (RL-) or O21-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - BODY GROUND)
  1. Disconnect the J5 and K5 front No. 1 speaker assembly connectors.

  1. Disconnect the I83 and I1 front No. 2 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I83-3 (+) or J5-1 - Body ground
    Always
    10 kΩ or higher
    I83-1 (-) or J5-2 - Body ground
    Always
    10 kΩ or higher
    I1-3 (+) or K5-1 - Body ground
    Always
    10 kΩ or higher
    I1-1 (-) or K5-2 - Body ground
    Always
    10 kΩ or higher


Result 
Result
Proceed to
NG
A
OK
B


B
Go to step 8
A

REPAIR OR REPLACE HARNESS AND CONNECTOR 

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER OR SPEAKERS - BODY GROUND)
  1. Disconnect the I152 and I153 radio and display receiver assembly connectors.

  1. Disconnect the I218 telematics transceiver connector.

  1. Disconnect the I1 front No. 2 speaker assembly LH connector.

  1. Disconnect the O18 and O21 rear speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I152-1 (FR+) or I218-2 (SPI+) - Body ground
    Always
    10 kΩ or higher
    I152-5 (FR-) or I218-3 (SPI-) - Body ground
    Always
    10 kΩ or higher
    I152-2 (FL+) or I1-4 (TWL+) - Body ground
    Always
    10 kΩ or higher
    I152-6 (FL-) or I1-2 (TWL-)- Body ground
    Always
    10 kΩ or higher
    I153-1 (RR+) or O18-1 - Body ground
    Always
    10 kΩ or higher
    I153-3 (RR-) or O18-2 - Body ground
    Always
    10 kΩ or higher
    I153-2 (RL+) or O21-1 - Body ground
    Always
    10 kΩ or higher
    I153-6 (RL-) or O21-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5.INSPECT TELEMATICS TRANSCEIVER
  1. Remove the telematics transceiver Click here.



    E169849E36
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (SPI+) - 5 (SPO+)
    Always
    Below 1 Ω
    3 (SPI-) - 6 (SPO-)
    Always
    Below 1 Ω
    2 (SPI+) - 3 (SPI-)
    Always
    10 kΩ or higher
    5 (SPO+) - 6 (SPO-)
    Always
    10 kΩ or higher
    2 (SPI+) or 5 (SPO+) - Body ground
    Always
    10 kΩ or higher
    3 (SPI-) or 6 (SPO-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Telematics Transceiver)



NG
REPLACE TELEMATICS TRANSCEIVER
OK


6.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY OR TELEMATICS TRANSCEIVER - BODY GROUND)
  1. Disconnect the I83 front No. 2 speaker assembly RH connector.

  1. Disconnect the I218 telematics transceiver connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I218-5 (SPO+) or I83-4 (TWR+) - Body ground
    Always
    10 kΩ or higher
    I218-6 (SPO-) or I83-2 (TWR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


7.CHECK (FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - BODY GROUND)
  1. Disconnect the J5 and K5 front No. 1 speaker assembly connectors.

  1. Disconnect the I83 and I1 front No. 2 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I83-3 (+) or J5-1 - Body ground
    Always
    10 kΩ or higher
    I83-1 (-) or J5-2 - Body ground
    Always
    10 kΩ or higher
    I1-3 (+) or K5-1 - Body ground
    Always
    10 kΩ or higher
    I1-1 (-) or K5-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


8.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly.
    for TMMK Made (Click here)
    for TMC, TMMR Made (Click here)

  1. Inspect the front No. 1 speaker assembly.
    for TMMK Made (Click here)
    for TMC, TMMR Made (Click here)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY
OK


9.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Remove the front No. 2 speaker assembly.
    for TMMK Made (Click here)
    for TMC, TMMR Made (Click here)

  1. Inspect the front No. 2 speaker assembly.
    for TMMK Made (Click here)
    for TMC, TMMR Made (Click here)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY
OK


10.INSPECT REAR SPEAKER ASSEMBLY
  1. Remove the rear speaker assembly.
    for TMMK Made (Click here)
    for TMC, TMMR Made (Click here)

  1. Inspect the front No. 2 speaker assembly.
    for TMMK Made (Click here)
    for TMC, TMMR Made (Click here)



NG
REPLACE REAR SPEAKER ASSEMBLY
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY