Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Smart Entry and Start System)

ENGINE IMMOBILISER SYSTEM (w/ Smart Entry and Start System) > Immobiliser System does not Operate Properly

for Preparation Click here


DESCRIPTION

The engine immobiliser system compares the ID code that is registered in the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.

WIRING DIAGRAM

Refer to "B2799"

INSPECTION PROCEDURE

CAUTION:
  1. The engine immobiliser system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the engine immobiliser system after confirming that the communication systems are functioning properly (Click here).
  2. When replacing the certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2, refer to Service Bulletin.
  3. After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

  1. *1: w/o Entry Function on Driver Door or for TMMK Made
  2. *2: w/ Entry Function on Driver Door except TMMK Made

HINT:
If an engine immobiliser system or SFI system DTC is output, first perform troubleshooting for the engine immobiliser system or SFI system DTC.

1.CHECK FOR DTC
  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTCs are not output
    A
    DTCs are output
    B



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


2.READ VALUE USING INTELLIGENT TESTER (IMMOBILISER FUEL CUT)
  1. for 2GR-FE or 2AR-FE

    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Engine and ECT (ECM) 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Immobiliser Fuel Cut
      Status of immobiliser fuel cut / ON or OFF
      -
      -

  1. for 6AR-FSE

    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Data List.

    5. Read the Data List according to the display on the GTS.

      Engine (ECM) 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Immobiliser Fuel Cut Status
      Status of immobiliser fuel cut / ON or OFF
      -
      -

OK:
OFF is displayed after the engine is started.

Result:
Result
Proceed to
NG
A
OK (for 2GR-FE)
B
OK (for 2AR-FE)
C
OK (for 6AR-FSE)
D



B
GO TO SFI SYSTEM (Click here)

C
GO TO SFI SYSTEM (Click here)

D
GO TO SFI SYSTEM (Click here)
A


3.CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts 5 seconds after the engine switch turned on (IG).

    OK:
    Engine starts normally.

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


4.SYSTEM CHECK
  1. Check the vehicle specification.

    Result:
    Result
    Proceed to
    w/o Entry Function on Driver Door or for TMMK Made
    A
    w/ Entry Function on Driver Door except TMMK Made
    B



B
Go to step 12
A


5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
  1. Disconnect the A43 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the A25*1 or A84*2 ECM connector.

    1. *1: for 2AR-FE
    2. *2: for 6AR-FSE

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 2AR-FE 
    Tester Connection
    Condition
    Specified Condition
    A43-14 (EFII) - A25-29 (IMO)
    Always
    Below 1 Ω
    A43-14 (EFII) or A25-29 (IMO) - Body ground
    Always
    10 kΩ or higher
    A43-13 (EFIO) - A25-28 (IMI)
    Always
    Below 1 Ω
    A43-13 (EFIO) or A25-28 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 6AR-FSE 
    Tester Connection
    Condition
    Specified Condition
    A43-14 (EFII) - A84-45 (IMO)
    Always
    Below 1 Ω
    A43-14 (EFII) or A84-45 (IMO) - Body ground
    Always
    10 kΩ or higher
    A43-13 (EFIO) - A45-28 (IMI)
    Always
    Below 1 Ω
    A43-13 (EFIO) or A45-28 (IMI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT ECM (TERMINAL IMI AND IMO)
  1. Reconnect the A43 certification ECU (smart key ECU assembly) connector.

  1. Reconnect the A25*1 or A84*2 ECM connector.

    1. *1: for 2AR-FE
    2. *2: for 6AR-FSE



  1. Using an oscilloscope, check the waveform.


    B372940E04


    Text in Illustration 
    *A
    for 2AR-FE
    *B
    for 6AR-FSE
    *a
    Component with harness connected
    (ECM)
    *b
    Approximately 160 ms
    *c
    Approximately 270 ms
    *d
    Approximately 40 ms
    *e
    Approximately 60 ms
    *f
    Waveform 1
    *g
    Waveform 2
    *h
    Waveform 3
    *i
    Waveform 1 (detail)
    -
    -

    Measurement Condition:

    for 2AR-FE 
    Tester Connection
    Condition
    Tool Setting
    Specified Condition
    A25-29 (IMO) - Body ground
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
    2 V/DIV., 500 ms./DIV.
    Pulse generation
    (See waveform 2)
    A25-28 (IMI) - Body ground
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
    2 V/DIV., 500 ms./DIV.
    Pulse generation
    (See waveform 1 and 3)

    for 6AR-FSE 
    Tester Connection
    Condition
    Tool Setting
    Specified Condition
    A84-45 (IMO) - Body ground
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
    2 V/DIV., 500 ms./DIV.
    Pulse generation
    (See waveform 2)
    A45-28 (IMI) - Body ground
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
    2 V/DIV., 500 ms./DIV.
    Pulse generation
    (See waveform 1 and 3)

    Result:
    Result
    Proceed to
    Normal waveform
    A
    Waveform 1 or 3 not output, or has abnormal wavelength or shape
    B
    Waveform 2 not output, or has abnormal wavelength or shape (for 2AR-FE)
    C
    Waveform 2 not output, or has abnormal wavelength or shape (for 6AR-FSE)
    D



B
Go to step 9

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)
A


7.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to Service Bulletin.


NEXT


8.CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts.

    OK:
    Engine starts normally.



NG
Go to step 9
OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE) 

9.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Replace the certification ECU (smart key ECU assembly) with a new one.

    HINT:
    Refer to Service Bulletin.


NEXT


10.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to Service Bulletin.


NEXT


11.CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts.

    OK:
    Engine starts normally.

Result:
Result
Proceed to
OK
A
NG (for 2AR-FE)
B
NG (for 6AR-FSE)
C



B
GO TO SFI SYSTEM (Click here)

C
GO TO SFI SYSTEM (Click here)
A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE) 

12.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
  1. Disconnect the I20 ID code box (immobiliser code ECU) connector.

  1. Disconnect the A25 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 2GR-FE 
    Tester Connection
    Condition
    Specified Condition
    I20-3 (EFII) - A25-30 (IMO)
    Always
    Below 1 Ω
    I20-3 (EFII) or A25-30 (IMO) - Body ground
    Always
    10 kΩ or higher
    I20-4 (EFIO) - A25-31 (IMI)
    Always
    Below 1 Ω
    I20-4 (EFIO) or A25-31 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 2AR-FE 
    Tester Connection
    Condition
    Specified Condition
    I20-3 (EFII) - A25-29 (IMO)
    Always
    Below 1 Ω
    I20-3 (EFII) or A25-29 (IMO) - Body ground
    Always
    10 kΩ or higher
    I20-4 (EFIO) - A25-28 (IMI)
    Always
    Below 1 Ω
    I20-4 (EFIO) or A25-28 (IMI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to Service Bulletin.


NEXT


14.CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts.

    OK:
    Engine starts normally.



NG
Go to step 15
OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE) 

15.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
  1. Replace the ID code box (immobiliser code ECU) with a new one.

    HINT:
    Refer to Service Bulletin.


NEXT


16.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to Service Bulletin.


NEXT


17.CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts.

    OK:
    Engine starts normally.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2GR-FE)
    B
    NG (for 2AR-FE)
    C



B
GO TO SFI SYSTEM (Click here)

C
GO TO SFI SYSTEM (Click here)
A

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)