DTC P012011 Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Ground |
DTC P012015 Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Battery or Open |
DTC P01201C Throttle / Pedal Position Sensor / Switch "A" Circuit Voltage Out of Range |
DTC P022011 Throttle/Pedal Position Sensor/Switch "B" Circuit Short to Ground |
DTC P022015 Throttle/Pedal Position Sensor/Switch "B" Circuit Short to Battery or Open |
DTC P21352B Throttle/Pedal Position Sensor/Switch "A"/"B" Voltage Correlation Signal Cross Coupled |

| DTC No. | DTC Detection Condition | Trouble Area |
| P012011 | The output voltage of VTA1 is less than 0.56 V for 2 seconds or more (1 trip detection logic). |
|
| P012015 | The output voltage of VTA1 is higher than 4.535 V for 2 seconds or more (1 trip detection logic). |
|
| P01201C | The difference between the output voltage of VTA1 and VTA2 is less than 0.8 V, or higher than 1.6 V for 2 seconds or more (1 trip detection logic). |
|
| P022011 | The output voltage of VTA2 is less than 2.05 V for 2 seconds or more (1 trip detection logic). |
|
| P022015 | The output voltage of VTA2 is higher than 4.75 V, and VTA1 is less than 2.367 V for 2 seconds or more (1 trip detection logic). |
|
| P21352B | The difference between the output voltages of VTA1 and VTA2 is 0.02 V or less for 2 seconds or more (1 trip detection logic). |
|
| GTS Display | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed (Engine Running) |
| Throttle Position Sensor No.1 Voltage | 0.5 to 1.1 V | 3.2 to 4.8 V |
| Throttle Position Sensor No.2 Voltage | 2.1 to 3.1 V | 4.6 to 4.98 V |
| Frequency of Operation | Continuous |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING GTS (THROTTLE POSITION SENSOR) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG) (or start the engine).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Throttle Position Sensor No.1 Voltage and Throttle Position Sensor No.2 Voltage.
Read the values displayed on the GTS.
| When Accelerator Pedal Fully Released | When Accelerator Pedal Fully Depressed (Engine Running) | Trouble Area | Proceed to | ||
| Throttle Position Sensor No.1 Voltage (VTA1) | Throttle Position Sensor No.2 Voltage (VTA2) | Throttle Position Sensor No.1 Voltage (VTA1) | Throttle Position Sensor No.2 Voltage (VTA2) | ||
| 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | VCTA circuit open | A |
| 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V | 4.5 to 4.98 V | ETA circuit open | |
| 0 to 0.2 V, or 4.5 to 4.98 V | 2.1 to 3.1 V (Fail-safe) | 0 to 0.2 V, or 4.5 to 4.98 V | 2.1 to 3.1 V (Fail-safe) | VTA1 circuit open or shorted to ground | |
| 0.6 to 1.4 V (Fail-safe) | 0 to 0.2 V, or 4.5 to 4.98 V | 0.6 to 1.4 V (Fail-safe) | 0 to 0.2 V, or 4.5 to 4.98 V | VTA2 circuit open or shorted to ground | |
| 0.5 to 1.1 V | 2.1 to 3.1 V | 3.2 to 4.8 V (Not fail-safe) | 4.6 to 4.98 V (Not fail-safe) | Throttle position sensor circuit normal | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
Disconnect the throttle body with motor assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E16-5 (VC) - E96-121 (VCTA) | Always | Below 1 Ω |
| E16-6 (VTA) - E96-122 (VTA1) | Always | Below 1 Ω |
| E16-4 (VTA2) - E96-88 (VTA2) | Always | Below 1 Ω |
| E16-3 (E2) - E96-120 (ETA) | Always | Below 1 Ω |
| E16-5 (VC) or E96-121 (VCTA) - Body ground and other terminals | Always | 10 kΩ or higher |
| E16-6 (VTA) or E96-122 (VTA1) - Body ground and other terminals | Always | 10 kΩ or higher |
| E16-4 (VTA2) or E96-88 (VTA2) - Body ground and other terminals | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT ECM (VC VOLTAGE) |
![]() |
Disconnect the throttle body with motor assembly connector.
| *a | Front view of wire harness connector (to Throttle Body with Motor Assembly) |
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E16-5 (VC) - E16-3 (E2) | Engine switch on (IG) | 4.5 to 5.5 V |
|
| ||||
| OK | |
| 4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY |
Replace the throttle body with motor assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P012011, P012015, P01201C, P022011, P022015 and/or P21352B are output | A |
| DTCs are not output | B |
|
| ||||
| A | ||
| ||