Home › Engine / Hybrid System · 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

DTC    P033511    Crankshaft Position Sensor "A" Circuit Short to Ground

DTC    P033515    Crankshaft Position Sensor "A" Circuit Short to Battery or Open

DTC    P03351F    Crankshaft Position Sensor "A" Circuit Intermittent

DTC    P03352A    Crankshaft Position Sensor "A" Signal Stuck in Range

DTC    P033531    Crankshaft Position Sensor "A" No Signal

for Preparation Click here


DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and a pickup coil. The crankshaft position sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The crankshaft position sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per crankshaft revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection and ignition timing are controlled.

DTC No.
DTC Detection Condition
Trouble Area
P033511
The crankshaft position sensor output voltage is less than 0.3 V for 4 seconds or more (1 trip detection logic).
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. ECM
P033515
The crankshaft position sensor output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. ECM
P03351F
Under conditions (a), (b) and (c), no crankshaft position sensor signal to ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed 1000 rpm or higher.
(b) Starter signal off.
(c) 3 seconds or more have elapsed since starter signal switched from on to off.
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Crankshaft (crankshaft position sensor plate)
  4. ECM
P03352A
No crankshaft position sensor signal to ECM while cranking (1 trip detection logic).
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Crankshaft (crankshaft position sensor plate)
  4. ECM
P033531
The engine stalls and the engine speed signal value decreases rapidly (1 trip detection logic).
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Crankshaft (crankshaft position sensor plate)
  4. ECM
Reference: Inspection using an oscilloscope.
A200774E01

HINT:
The correct waveform is as shown.
ECM Terminal Name
Between NE+ and NE-
Tester Range
2 V/DIV., 20 ms./DIV.
Condition
Idling with warm engine


MONITOR DESCRIPTION

A DTC will be stored if any of the following occurs:
  1. The crankshaft position sensor signal (NE signal) is not received by the ECM when the engine is being cranked.
  2. The crankshaft position sensor signal (NE signal) is not received by the ECM when the engine is running.
  3. The engine stalls and the engine speed signal value decreases rapidly (under normal conditions the engine speed will decrease gradually).
  4. The crankshaft position sensor output voltage is above or below the threshold.

MONITOR STRATEGY


Required Sensors/Components (Main)
Crankshaft position sensor
Required Sensors/Components (Related)
Camshaft position sensor
Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the GTS to the DLC3.
  2. Turn the engine switch on (IG) and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the GTS on.
  6. Start the engine.
  7. Idle the engine for 20 seconds or more.
  8. Enter the following menus: Powertrain / Engine / Trouble Codes.
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  11. Input the DTC: P033511, P033515, P03351F, P03352A or P033531.
  12. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


WIRING DIAGRAM


A298889E01


INSPECTION PROCEDURE

HINT:
  1. If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.
  2. The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:
    1. Connect the GTS to the DLC3.
    2. Turn the engine switch on (IG).
    3. Turn the GTS on.
    4. Start the engine.
    5. Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Speed.
      The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor.
      Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.
  3. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING GTS (ENGINE SPEED)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Speed.

  1. Start the engine.

  1. Read the values displayed on the GTS while the engine is running.

    OK:
    Correct values are displayed.

    HINT:
    1. To check the engine speed change, display the graph on the GTS.
    2. If the engine does not start, check the engine speed while cranking.
    3. If the engine speed indicated on the GTS remains zero (0), there may be an open or short in the crankshaft position sensor circuit.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CRANKSHAFT POSITION SENSOR)


    A338257E01
  1. Disconnect the crankshaft position sensor connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Crankshaft Position Sensor)

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E100-1 (VC) - Body ground
    Engine switch on (IG)
    4.5 to 5.5 V



NG
Go to step 8
OK


3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E100-3 (NE+) - E96-76 (NE+)
    Always
    Below 1 Ω
    E100-2 (NE-) - E96-109 (NE-)
    Always
    Below 1 Ω
    E100-3 (NE+) or E96-76 (NE+) - Body ground and other terminals
    Always
    10 kΩ or higher
    E100-2 (NE-) or E96-109 (NE-) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)


    B319222E01
  1. Check the crankshaft position sensor installation condition.
    Text in Illustration 
    *a
    Clearance

    OK:
    Crankshaft position sensor is installed correctly.



NG
SECURELY REINSTALL CRANKSHAFT POSITION SENSOR (Click here)
OK


5.INSPECT CRANKSHAFT (TEETH OF CRANKSHAFT POSITION SENSOR PLATE)
  1. Inspect the teeth of the crankshaft position sensor plate.

    OK:
    Crankshaft position sensor plate does not have any cracks or deformation.



NG
REPLACE CRANKSHAFT (Click here)
OK


6.REPLACE CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P033511, P033515, P03351F, P03352A AND/OR P033531)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTCs are not output
    A
    P033511, P033515, P03351F, P03352A and/or P033531 is output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END 

8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E100-1 (VC) - E96-110 (VCNE)
    Always
    Below 1 Ω
    E100-1 (VC) or E96-110 (VCNE) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)