Home › Engine / Hybrid System · 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

DTC    P052012    Engine Oil Pressure Sensor/Switch "A" Circuit Short to Battery

DTC    P052014    Engine Oil Pressure Sensor/Switch "A" Circuit Short to Ground or Open

DTC    P052024    Engine Oil Pressure Sensor/Switch "A" Signal Stuck High

DTC    P05202A    Engine Oil Pressure Sensor/Switch "A" Signal Stuck in Range

DTC    P052400    Engine Oil Pressure Too Low

for Preparation Click here


DESCRIPTION

The oil pump is a variable discharge type. The oil pump maintains the oil pressure in the required for VVT operation at low engine speeds and for lubrication at high engine speeds, and reduces friction to lower the excess oil pressure at middle engine speeds. The oil pressure sender gauge assembly detects the engine oil pressure.

DTC No.
DTC Detection Condition
Trouble Area
P052012
The oil pressure sender gauge assembly output voltage is higher than 4.78 V for 5 seconds or more (1 trip detection logic).
  1. Open or short in oil pressure sender gauge assembly circuit
  2. Oil pressure sender gauge assembly
  3. ECM
P052014
The oil pressure sender gauge assembly output voltage is less than 0.23 V for 5 seconds or more (1 trip detection logic).
  1. Open or short in oil pressure sender gauge assembly circuit
  2. Oil pressure sender gauge assembly
  3. ECM
P052024
The oil pressure sender gauge assembly output voltage is higher than the threshold value (1 trip detection logic).
  1. Open or short in oil pressure sender gauge assembly circuit
  2. Oil pressure sender gauge assembly
  3. ECM
P05202A
The oil pressure sender gauge assembly output voltage is the same value for a certain period of time (1 trip detection logic).
  1. Open or short in oil pressure sender gauge assembly circuit
  2. Oil pressure sender gauge assembly
  3. ECM
P052400
The oil pressure sender gauge assembly output voltage is at or below the threshold value (1 trip detection logic).
  1. Open or short in oil pressure sender gauge assembly circuit
  2. Oil pressure sender gauge assembly
  3. ECM
  4. Engine oil amount insufficient

MONITOR DESCRIPTION

The ECM calculates the engine oil pressure from the oil pressure sender gauge assembly output voltage. does not match the target voltage based on engine speed or does not change for a certain period of time, the oil pressure sender gauge assembly may be malfunctioning or have an open or short in its circuit. In this case, the ECM illuminates the MIL and stores a DTC.

MONITOR STRATEGY


Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN


A331687E02

  1. Connect the GTS to the DLC3.
  2. Turn the engine switch on (IG) and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the GTS on.
  6. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switches turned off [A].
  7. With the vehicle is stationary, gently depress the accelerator pedal and maintain an engine speed of 4000 rpm for 1 minute, then release the accelerator pedal and return to the engine idling [B].
  8. Repeat step [B] 3 times or more.
  9. Enter the following menus: Powertrain / Engine / Trouble Codes.
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  12. Input the DTC: P052012, P052014, P052024, P05202A or P052400.
  13. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


WIRING DIAGRAM


A330721E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P052012, P052014, P052024, P05202A OR P052400
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P052012, P052014, P052024, P05202A and/or P052400 is output
    A
    DTC P052012, P052014, P052024, P05202A and/or P052400 and other DTCs are output
    B

    HINT:
    If any DTCs other than P052012, P052014, P052024, P05202A an/or P052400 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK ENGINE OIL LEVEL
  1. Check the engine oil level.

  1. Check the state of the oil level warning light.

    Result:

    Result
    Proceed to
    Engine oil level is low and oil level warning light is illuminated
    A
    Engine oil level is within the specified range and oil level warning light is not illuminated
    B

    HINT:
    If the oil level warning light is not illuminated even though the engine oil level is below the Low mark, or the oil level warning light is illuminated even though the engine oil level is within the specified range, inspect the oil level sensor and related parts.



B
Go to step 5
A


3.INSPECT FOR ENGINE OIL LEAK
  1. Check for engine oil leaks.

    OK:
    There are no engine oil leaks.

    HINT:
    If there are engine oil leaks, perform repairs.


NEXT


4.ADD ENGINE OIL
  1. Add engine oil (Click here).

    NOTICE:
    Do not add engine oil to above the full level mark.


NEXT


5.CHECK WHETHER DTC OUTPUT RECURS (DTC P052012, P052014, P052024, P05202A OR P052400)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTCs are not output
    A
    DTC P052012, P052014, P052024, P05202A and/or P052400 is output
    B



B
Go to step 6
A

END 

6.INSPECT OIL PRESSURE SENDER GAUGE ASSEMBLY
  1. Read the value displayed on the GTS.

    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Oil Temperature Sensor and Engine Oil Pressure.

    5. With the engine oil temperature at 75 to 85°C (167 to 185°F), read the "Engine Oil Pressure" with the engine speed at 1000 rpm.

  1. Read the oil pressure using an oil pressure gauge.

    1. Install the oil pressure gauge .

    2. Start the engine.

    3. With the engine oil temperature at 75 to 85°C (167 to 185°F), read the oil pressure gauge with the engine speed at 1000 rpm.

  1. Compare the Data List value and the oil pressure gauge reading.

    OK:
    Data List value and gauge reading are within +/-50 kPa of each other



NG
Go to step 10
OK


7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF OIL PRESSURE SENDER GAUGE ASSEMBLY)


    A248180E11
  1. Disconnect the oil pressure sender gauge assembly connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Oil Pressure Sender Gauge Assembly)

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E103-3 (VC) - Body ground
    Engine switch on (IG)
    4.75 to 5.25 V



NG
Go to step 9
OK


8.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENDER GAUGE ASSEMBLY - ECM)
  1. Disconnect the oil pressure sender gauge assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E103-2 (PEO) - E96-98 (PEO)
    Always
    Below 1 Ω
    E103-1 (E2) - E96-129 (EPEO)
    Always
    Below 1 Ω
    E103-2 (PEO) or E96-98 (PEO) - Body ground and other terminals
    Always
    10 kΩ or higher
    E103-1 (E2) or E96-129 (EPEO) - Body ground and other terminals
    Always
    10 kΩ or higher



OK
Go to step 11

NG
REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENDER GAUGE ASSEMBLY - ECM)
  1. Disconnect the oil pressure sender gauge assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E103-3 (VC) - E96-130 (VCPE)
    Always
    Below 1 Ω
    E103-3 (VC) or E96-130 (VCPE) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

10.REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY
  1. Replace the oil pressure sender gauge assembly (Click here).


NEXT


11.CHECK WHETHER DTC OUTPUT RECURS (DTC P052012, P052014, P052024, P05202A OR P052400)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTCs are not output
    A
    DTC P052012, P052014, P052024, P05202A and/or P052400 is output
    B



B
REPLACE ECM (Click here)
A

END