DTC P211900 Throttle Actuator "A" Control Throttle Body Range/Performance |
DTC P211904 Throttle Actuator "A" Control Throttle Body Range/Performance System Internal Failure |
DTC P211977 Throttle Actuator "A" Control Throttle Body Range/Performance Commanded Position Not Reachable |
| DTC No. | DTC Detection Condition | Trouble Area |
| P211900 | The throttle valve opening angle continues to vary greatly from the target opening angle (1 trip detection logic). |
|
| P211904 | The throttle valve opening angle continues to vary greatly from the target opening angle (1 trip detection logic). |
|
| P211977 | The throttle valve opening angle continues to vary greatly from the target opening angle (1 trip detection logic). |
|
| Required Sensors/Components | Throttle actuator (throttle body with motor assembly) |
| Frequency of Operation | Continuous |
| System guard* judge condition | On |
| *: System guard is on when the following conditions are met | - |
| Throttle actuator | On |
| Throttle actuator duty calculation | Executing |
| Throttle position sensor fail | Not detected |
| Throttle actuator current-cut operation | Not executing |
| Throttle actuator power supply | 4 V or higher |
| Throttle actuator fail | Not detected |
| Either of the following conditions is met | A or B |
| A. Difference between commanded closed throttle position and current closed throttle position | 0.3 V or higher |
| B. Difference between commanded open throttle position and current open throttle position | 0.3 V or higher |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P211900, P211904 OR P211977) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P211900, P211904 or P211977 is output | A |
| DTC P211900, P211904 or P211977 and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING GTS (THROTTLE POSITION) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Throttle Position Sensor No.1 Voltage and Throttle Position Command.
Read the values displayed on the GTS while fully depressing and releasing the accelerator pedal quickly.
| Result | Proceed to |
| Throttle Position Sensor No.1 Voltage does not change | A |
| Throttle Position Sensor No.1 Voltage changes even a little | B |
|
| ||||
| A | |
| 3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR) |
Inspect the throttle body with motor assembly (Click here).
|
| ||||
| OK | |
| 4.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE) |
Check for contamination between the throttle valve and housing. If necessary, clean the throttle body with motor assembly. Also, check that the throttle valve moves smoothly.
|
| ||||
| OK | |
| 5.READ VALUE USING GTS (THROTTLE POSITION) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Throttle Position Sensor No.1 Voltage, Throttle Position Sensor No.2 Voltage and Throttle Position Command.
Read the values displayed on the GTS while wiggling the ECM wire harness.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| Value in Data List changes when wire harness is wiggled, or DTC is output | A |
| Other than above | B |
|
| ||||
| A | |
| 6.REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM) |
As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (Click here).
| NEXT | ||
| ||
| 7.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY |
Replace the throttle body with motor assembly (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P211900, P211904 OR P211977) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTCs are not output | A |
| DTC P211900, P211904 or P211977 is output | B |
|
| ||||
| A | ||
| ||