Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM33A0E _59 Vehicle Exterior _065394 WIPER / WASHER _0320457 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Washer Motor Circuit  


DESCRIPTION

When the windshield washer motor and pump assembly receives signals from the windshield wiper switch assembly it operates to spray washer fluid from the washer nozzle sub-assemblies.

WIRING DIAGRAM

E365918E04
1.344,0.573 2.26,0.771 0.917,0.198 10 false LIN3 5.479,0.552 6.396,0.75 0.917,0.198 10 false LIN 5.417,1.125 6.021,1.323 0.604,0.198 10 false A31 5.427,1.281 6.906,1.646 1.479,0.365 10 false Windshield Wiper Motor Assembly 4.885,0.406 5.49,0.604 0.604,0.198 10 false 2*1, 3*2 1.719,0.406 2.323,0.604 0.604,0.198 10 false 3 2.094,2.302 3.667,2.563 1.573,0.26 10 false from IG1 NO. 2 Relay 4.292,2.448 5.208,2.646 0.917,0.198 10 false WASHER 1.698,3.385 2.302,3.583 0.604,0.198 10 false 12 1.208,3.385 2.125,3.583 0.917,0.198 10 false FWSR 2.729,4.146 3.646,4.344 0.917,0.198 10 false WASHER 3.74,4.281 6.667,4.698 2.927,0.417 10 false Windshield Washer Motor and Pump Assembly 3.74,4.135 4.344,4.333 0.604,0.198 10 false A32 0.167,4.146 0.771,4.344 0.604,0.198 10 false K51 0.167,4.302 1.792,4.99 1.625,0.688 10 false Main Body ECU (Multiplex Network Body ECU) 0.938,5.156 3.313,5.427 2.375,0.271 10 false : LIN Communication Line 2.594,3.385 3.198,3.583 0.604,0.198 10 false 2 2.594,3.75 3.198,3.948 0.604,0.198 10 false 3 3.354,3.375 3.958,3.573 0.604,0.198 10 false 1 3.354,3.75 3.958,3.948 0.604,0.198 10 false 5 4.594,3.771 5.198,3.969 0.604,0.198 10 false 2 5.333,3.771 5.938,3.969 0.604,0.198 10 false 1 3.531,5.156 4.51,5.385 0.979,0.229 10 false *1: for LHD 4.51,5.146 5.49,5.375 0.979,0.229 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*1

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*2

*1: w/ Door Control Battery

*2: w/ Smart Entry and Start System




PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Washer Relay Function to operate the windshield washer motor and pump assembly OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Front Washer Relay
50004 123 77
OK:

Windshield washer motor and pump assembly operates normally.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY
2.INSPECT WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY
a.

Remove the windshield washer motor and pump assembly.

Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR>REMOVAL


b.

Inspect the windshield washer motor and pump assembly.

Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT WASHER RELAY

NG

REPLACE WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY

3.INSPECT WASHER RELAY
a.

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WASHER RELAY)

NG

REPLACE WASHER RELAY

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WASHER RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (WASHER relay) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A32-1 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (WASHER RELAY - WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (WASHER RELAY - WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (WASHER relay) - A32-2 Always Below 1 Ω
5 (WASHER relay) or A32-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (WASHER RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (WASHER RELAY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (WASHER relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - WASHER RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - WASHER RELAY)
a.

Disconnect the K51 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K51-12 (FWSR) - 2 (WASHER relay) Always Below 1 Ω
K51-12 (FWSR) or 2 (WASHER relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR