Home › Engine / Hybrid System › 2AR-FE (ENGINE MECHANICAL) › ENGINE › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065324 2AR-FE ENGINE MECHANICAL _0321401 ENGINE G

2AR-FE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
A379926

To prevent injury due to contact with an operating V-ribbed belt or cooling fan, keep your hands and clothing away from the V-ribbed belt and cooling fans when working in the engine compartment with the engine running or the ignition switch on (IG).


PROCEDURE

Hide 17801 5.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.

Click hereGeneral>MAINTENANCE>2AR-FE AIR CLEANER FILTER ELEMENT>REMOVAL


b.

Visually check that the air cleaner filter element sub-assembly is not damaged or excessively oily. If necessary, replace the air cleaner filter element sub-assembly.

HINT:
·

If there is any dirt or clogs in the air cleaner filter element sub-assembly, clean it with compressed air.

·

If any dirt or clogs remain even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.




c.

Install the air cleaner filter element sub-assembly.

Click hereGeneral>MAINTENANCE>2AR-FE AIR CLEANER FILTER ELEMENT>INSTALLATION


Hide 16620 7.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY

a.

Remove the V-ribbed belt.

Click hereGeneral>MAINTENANCE>2AR-FE DRIVE BELT>REMOVAL


b.

Turn the V-ribbed belt tensioner assembly clockwise and counterclockwise and check that it turns smoothly and does not catch.

HINT:

If the V-ribbed belt tensioner assembly does not turn smoothly or catches, replace the V-ribbed belt tensioner assembly.



c.

Install the V-ribbed belt.

Click hereGeneral>MAINTENANCE>2AR-FE DRIVE BELT>INSTALLATION


Hide 13750 8.INSPECT VALVE LASH ADJUSTER ASSEMBLY

a.

Rev up the engine several times. Check that the engine does not emit unusual noises.


b.

If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the inspection.

HINT:

If any defects or problems are found during the inspection, perform the valve lash adjuster assembly inspection.

Click hereEngine / Hybrid System>2AR-FE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION



Hide 9.INSPECT IGNITION TIMING

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Start the engine and run it at idle.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine / Data List / IGN Advance.

Powertrain > Engine and ECT > Data List
Tester Display
IGN Advance
50003 234 29
Standard ignition timing:

5 to 20° BTDC at idle


NOTICE:
·

Check the ignition timing with the cooling fans off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.




v.

Enter the following menus: Powertrain / Engine / Active Test / Connect the TC and TE1 / ON.

Powertrain > Engine and ECT > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
IGN Advance
50004 234 13 29

vi.

Monitor IGN Advance of the Data List.

Standard ignition timing:

8 to 12° BTDC at idle



vii.

Enter the following menus: Powertrain / Engine / Active Test / Connect the TC and TE1 / OFF.


viii.

Check that the ignition timing advances immediately when the engine speed is increased.



c.

When not using the GTS:

i.
A206183C10
1.771,1.479 2.083,1.917 2.083,1.917 2.167,1.917 true 1.604,0.927 1.333,0.396 1.333,0.396 1.219,0.396 true 0.073,0.083 0.438,0.385 0.365,0.302 10 *a 2.208,1.833 2.521,2.031 0.313,0.198 10 TC 1,0.313 1.396,0.552 0.396,0.24 10 CG
*a DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:
·

Confirm the terminal numbers before connecting them. Connecting the wrong terminals may damage electrical components.

·

Check the ignition timing with the cooling fans off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.




ii.

Remove the No. 1 engine cover sub-assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


iii.

Pull out the wire harness.


iv.
A210177

Connect the clip of a timing light to the wire harness.

NOTICE:

Use a timing light that detects primary signals.



v.

Check the ignition timing at idle.

Standard ignition timing:

8 to 12° BTDC at idle



vi.

Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.


vii.

Check the ignition timing at idle.

Standard ignition timing:

5 to 20° BTDC at idle


HINT:

If the ignition timing is not as specified, check the valve timing.



viii.

Check that the ignition timing advances immediately when the engine speed is increased.


ix.

Disconnect the timing light from the engine.


x.

Install the No. 1 engine cover sub-assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION



Hide 10.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Race the engine at 2500 rpm for approximately 90 seconds.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

v.

Read the value displayed on the tester.

Standard idle speed:

610 to 710 rpm


NOTICE:
·

Check the engine idle speed with the cooling fans off.

·

Turn off all electrical systems and the A/C.

·

When checking the engine idle speed, the transaxle should be in neutral or park.





c.

When not using the GTS:

i.
A206183C66
1.042,1.906 1.042,1.479 false 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.938,1.938 1.396,2.135 0.458,0.198 10 false TAC
*a DLC3


Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.

SST
09843-18030  

NOTICE:

Be sure to connect the tachometer probe to the correct terminal. Connecting the wrong terminals can cause damage to electrical components.



ii.

Start the engine and run it at idle.


iii.

Inspect the engine idle speed.

Standard idle speed:

610 to 710 rpm


NOTICE:
·

Check the engine idle speed with the cooling fans off.

·

Turn off all electrical systems and the A/C.

·

When checking the engine idle speed, the transaxle should be in neutral or park.




iv.

Disconnect the tachometer probe from terminal 9 (TAC) of the DLC3.



Hide 11.INSPECT COMPRESSION

NOTICE:

Keep the spark plug holes free of foreign matter when measuring the compression pressure.


a.

Warm up and stop the engine.




d.

Disconnect the 4 fuel injector connectors.


e.
A407913

Insert a compression gauge into the spark plug hole.


f.

Fully open the throttle.


g.

While cranking the engine, measure the compression pressure.

Standard compression pressure:

1450 kPa (14.8 kgf/cm2, 210 psi)


Minimum pressure:

980 kPa (10.0 kgf/cm2, 142 psi)


Difference between each cylinder:

200 kPa (2.0 kgf/cm2, 29 psi) or less


NOTICE:
·

Always use a fully charged battery to obtain an engine speed of 250 rpm or more.

·

Inspect all cylinders in the same way.

·

Measure the compression pressure as quickly as possible.




h.

If the cylinder compression pressure is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect it again.

HINT:
·

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

·

If the compression pressure stays low, a valve may be stuck or seated improperly, or there may be leaks in the cylinder head gasket.




i.

Connect the 4 fuel injector connectors.



k.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

After the inspection, clear the DTCs, check for DTCs again and make sure the normal system code is output.



Hide 12.INSPECT CO/HC

HINT:

This check determines whether or not the idle CO/HC complies with regulations.


a.

Start the engine.


b.

Run the engine at 2500 rpm for approximately 180 seconds.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idle.


d.

Immediately check the CO/HC concentration during idle and when the engine is running at 2500 rpm.

HINT:

When performing a 2 mode (with the engine idling/running at 2500 rpm) test, the measurement procedures are determined by applicable local regulations.

If the CO/HC concentration does not comply with the regulations, perform troubleshooting in the order given below.



ii.

See the following table for possible causes, then inspect the applicable parts and repair them if necessary.

CO HC Problem Cause
Normal High Rough idle
1.

Faulty ignition:

-

Incorrect valve timing

-

Fouled, shorted or improperly gapped spark plugs


2.

Incorrect valve clearance (valve lash adjuster assembly)

3.

Leaks in intake or exhaust valves

4.

Leaks in cylinders


Low High Rough idle (Fluctuating HC reading)
1.

Vacuum leaks:

-

PCV hoses

-

Intake manifold

-

Throttle body with motor assembly


2.

Lean mixture causing misfire


High High Rough idle (Black smoke from exhaust)
1.

Restricted air cleaner filter element sub-assembly

2.

Plugged PCV valve

3.

Faulty SFI systems:

-

Fuel pressure regulator assembly

-

Engine coolant temperature sensor

-

Mass air flow meter sub-assembly

-

ECM

-

Fuel injector assemblies

-

Throttle position sensor (built into throttle body with motor assembly)