Home › Engine / Hybrid System › 2AR-FE (ENGINE MECHANICAL) › ENGINE UNIT › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065324 2AR-FE ENGINE MECHANICAL _0321408 ENGINE UNIT G

2AR-FE ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13801 1.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A160725

Turn the roller by hand to check that it turns smoothly.

HINT:

If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.



Hide 13750 2.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the valve lash adjuster assembly free from dirt and foreign matter.

·

Only use clean engine oil.



a.

Place the valve lash adjuster assembly into a container filled with engine oil.

A293105C31
1.5,0.302 1.969,0.302 false 2.344,0.302 2.875,0.302 false 1.448,0.958 2.052,0.698 true 2.313,0.698 2.896,0.865 true 1.5,1.125 2.063,0.938 false 2.302,0.938 2.833,1.083 false 1.385,1.406 2.052,1.229 true 2.313,1.219 2.938,1.365 true 1.302,1.99 2.052,1.583 true 2.323,1.573 3.042,1.969 true 1.469,2.115 2.063,1.958 true 2.323,1.958 2.875,2.104 true 4.698,1.104 5.052,1.354 true 2.115,0.844 2.427,1 0.313,0.156 10 false *f 2.115,1.469 2.313,1.708 0.198,0.24 10 false *g 1.229,0.031 1.542,0.188 0.313,0.156 10 false *a 3.01,0.031 3.323,0.188 0.313,0.156 10 false *b 2.115,0.594 2.427,0.75 0.313,0.156 10 false *c 2.115,1.135 2.427,1.292 0.313,0.156 10 false *d 2.115,1.854 2.427,2.01 0.313,0.156 10 false *e 2.031,0.219 2.49,0.417 0.458,0.198 10 false SST 4.427,0.938 4.885,1.135 0.458,0.198 10 false SST
*a Correct *b Incorrect
*c Taper *d Low Pressure Chamber
*e High Pressure Chamber *f Plunger
*g Check Ball - -



b.

Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  


c.

Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed the air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding air from the high-pressure chamber, make sure that the tip of SST is pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding the air, remove SST. Then try to quickly and firmly press the plunger by hand.

OK:

The plunger is very difficult to move.


HINT:

If the plunger is easy to move, replace the valve lash adjuster assembly.



Hide 13511 3.INSPECT CAMSHAFT

a.
A196939

Inspect the camshaft for runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the runout at the center journal.

Maximum Runout:

0.03 mm (0.00118 in.)


HINT:
·

Check the camshaft oil clearance after replacing the camshaft.

·

If the runout is more than the maximum, replace the camshaft.





b.
A196940

Inspect the cam lobes.

i.

Using a micrometer, measure the cam lobe height.

Standard Cam Lobe Height:

44.163 to 44.305 mm (1.73870 to 1.74429 in.)


Minimum Cam Lobe Height:

44.013 mm (1.73279 in.)


HINT:

If the cam lobe height is less than the minimum, replace the camshaft.




c.
A196941

Inspect the camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 34.449 to 34.465 mm (1.35626 to 1.35689 in.)
Other journals 22.959 to 22.975 mm (0.90390 to 0.90453 in.)


HINT:

If the journal diameter is not as specified, check the camshaft oil clearance.

Click hereEngine / Hybrid System>2AR-FE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION




Hide 13512 4.INSPECT NO. 2 CAMSHAFT

a.
A196939

Inspect the No. 2 camshaft for runout.

i.

Place the No. 2 camshaft on V-blocks.


ii.

Using a dial indicator, measure the runout at the center journal.

Maximum Runout:

0.03 mm (0.00118 in.)


HINT:
·

Check the camshaft oil clearance after replacing the No. 2 camshaft.

·

If the runout is more than the maximum, replace the No. 2 camshaft.





b.
A196940

Inspect the cam lobes.

i.

Using a micrometer, measure the cam lobe height.

If the cam lobe height is less than the minimum, replace the No. 2 camshaft.

Standard Cam Lobe Height:

44.144 to 44.286 mm (1.73795 to 1.74354 in.)


Minimum Cam Lobe Height:

43.996 mm (1.73212 in.)




c.
A196941

Inspect the No. 2 camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 34.449 to 34.465 mm (1.35626 to 1.35689 in.)
Other journals 22.959 to 22.975 mm (0.90390 to 0.90453 in.)


HINT:

If the journal diameter is not as specified, check the camshaft oil clearance.

Click hereEngine / Hybrid System>2AR-FE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION




Hide 13511 5.INSPECT CAMSHAFT OIL CLEARANCE

NOTICE:

Do not turn the camshafts.


a.

Clean the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, 3 No. 3 camshaft bearing caps, camshaft housing sub-assembly and camshaft journals.


b.

Place the camshaft and No. 2 camshaft on the camshaft housing sub-assembly.


c.
A259165C08
1.333,0.802 0.979,0.083 0.979,0.083 0.885,0.083 true 0.688,0 0.906,0.177 0.219,0.177 10 false *a
*a Plastigage


Lay a strip of Plastigage across each of the camshaft journals.


d.

e.

f.

Remove the camshaft bearing caps.

Click hereEngine / Hybrid System>2AR-FE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL


g.
A259166C08
1.354,1.01 1.01,0.302 1.01,0.302 0.917,0.302 true 0.49,3.167 0.979,2.375 0.979,2.375 0.479,3.823 true 1.063,3.865 1.885,4.427 1.885,4.427 2.802,3.865 true 1.052,3.188 1.885,4.427 1.885,4.427 2.771,3.188 true 1.646,3.188 1.885,4.427 1.885,4.427 2.219,3.188 true 1.646,3.865 1.885,4.427 1.885,4.427 2.24,3.865 true 0.719,0.229 1.01,0.479 0.292,0.25 10 false *a 1.01,2.281 1.198,2.458 0.188,0.177 10 false *b 1.823,4.469 2.094,4.646 0.271,0.177 10 false *c
*a Plastigage
*b No. 1 Journal
*c Other Journal


Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Specified Condition
Intake No. 1 journal 0.035 to 0.072 mm (0.00138 to 0.00283 in.)
Exhaust No. 1 journal 0.049 to 0.086 mm (0.00193 to 0.00339 in.)
Other journals 0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake No. 1 journal 0.085 mm (0.00335 in.)
Exhaust No. 1 journal 0.095 mm (0.00374 in.)
Other journals 0.085 mm (0.00335 in.)


HINT:

If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the camshaft housing sub-assembly.



Hide 13050 6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13506 7.INSPECT CHAIN SUB-ASSEMBLY

a.
A386378C14
1.729,0.979 2.042,1.177 0.313,0.198 10 false *a 0.979,2.01 1.188,2.177 0.208,0.167 10 false 0 1.385,2 1.583,2.177 0.198,0.177 10 false 1 1.99,2.021 2.313,2.177 0.323,0.156 10 false 14 2.396,2.01 2.667,2.177 0.271,0.167 10 false 15
*a Measurement Area


Using a spring scale, pull the chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 15 links.

Maximum Chain Elongation:

137.7 mm (5.42 in.)


NOTICE:

Perform the measurement at 3 random places. Use the average of the measurements.


HINT:

If the average elongation is more than the maximum, replace the chain sub-assembly.



Hide 13070A 8.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A350373C01
0.719,0.74 0.854,0.74 0.854,0.74 0.906,1.292 false 2.729,1 2.573,1.25 2.573,1.25 2.333,1.25 true 0.438,0.667 0.896,0.865 0.458,0.198 10 false SST 2.146,1.156 2.458,1.354 0.313,0.198 10 false *a
*a Hexagonal Portion


Using SST, grip the hexagonal portion, and then secure the SST and No. 2 camshaft in a vise as shown in the illustration.

SST
09212-31010  

NOTICE:
·

Do not damage the No. 2 camshaft.

·

Never grip areas other than the hexagonal portion, as this may cause damage.




b.
A196902C36
1.896,0.656 1.771,0.656 1.771,0.656 1.594,0.927 false 1.229,0.177 1.104,0.177 1.104,0.177 0.667,0.802 true 1.938,0.552 2.115,0.719 0.177,0.167 10 false *b 1.281,0.104 1.469,0.271 0.188,0.167 10 false *a
*a Knock Pin Hole
*b Knock Pin


Align and fit the knock pin of the No. 2 camshaft with the knock pin hole of the camshaft timing exhaust gear assembly.


c.
A196904C47
2.167,0.844 1.917,0.844 1.917,0.844 1.49,1.094 false 0.823,0.75 0.917,0.75 0.917,0.75 1.135,0.99 false 0.604,0.667 0.781,0.823 0.177,0.156 10 *1 1.802,0.531 2,0.698 0.198,0.167 10 *c 2.188,0.75 2.365,0.917 0.177,0.167 10 *2 1.74,2.021 1.938,2.177 0.198,0.156 10 *d 0.063,0.042 0.25,0.208 0.188,0.167 10 *a 0.063,1.833 0.26,2 0.198,0.167 10 *b
*1 Camshaft Timing Exhaust Gear Assembly
*2 Camshaft Flange
*a Incorrect
*b Correct
*c Gap
*d No Gap


Check that there is no gap between the camshaft timing exhaust gear assembly and camshaft flange.


d.

While securely holding the No. 2 camshaft, install the bolt of the camshaft timing exhaust gear assembly by hand.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

NOTICE:

Do not use any tools to install the bolt. If the bolt is installed using a tool, the lock pin will be damaged.



e.

Check the lock of the camshaft timing exhaust gear assembly.

i.

Make sure that the camshaft timing exhaust gear assembly is locked.

NOTICE:

Be careful not to damage the No. 2 camshaft.




f.

Release the lock pin.

A292249C14
1.25,1.115 1.677,1.115 false 2.094,1.219 2.521,1.219 false 1.031,2.823 1.448,2.698 true 2.302,2.375 2.625,2.521 2.625,2.521 1.74,2.625 true 5.042,1.208 5.354,1.573 true 4.625,1.542 5.135,1.74 true 4.688,2.406 5.167,2.104 true 5.604,2.115 6.063,2.406 true 5.656,1.74 6.135,1.5 true 2.708,2.427 3.021,2.583 0.313,0.156 10 false *e 0.865,2.792 1.177,2.948 0.313,0.156 10 false *f 4.917,1 5.26,1.26 0.344,0.26 10 false *g 2.583,1.135 2.896,1.292 0.313,0.156 10 false *a 1.063,1.031 1.375,1.188 0.313,0.156 10 false *b 6.167,1.396 6.479,1.552 0.313,0.156 10 false *c 6.125,2.375 6.438,2.531 0.313,0.156 10 false *d 4.448,1.427 4.76,1.583 0.313,0.156 10 false *c 4.521,2.375 4.833,2.531 0.313,0.156 10 false *d
*a Retard Side Path *b Advance Side Path
*c Open *d Closed
*e Rubber Piece *f Vinyl Tape
*g Knock Pin - -


i.

Clean the camshaft journal with non-residue solvent.


ii.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

HINT:

There are 4 oil paths in the grooves of the No. 2 camshaft. Plug 2 oil paths with rubber pieces.



iii.

Make a hole in the vinyl tape placed on the advance side path. Make a hole in the vinyl tape placed on the retard side path on the opposite side to that of the advance side path as shown in the illustration.


iv.
A198157C20
1.01,0.198 1.156,0.198 1.156,0.198 1.531,1.333 true 2.281,0.188 2.135,0.188 2.135,0.188 1.854,1.208 true 0.792,0.052 0.99,0.219 0.198,0.167 10 false *a 2.365,0.104 2.563,0.271 0.198,0.167 10 false *b
*a Retard Side Path
*b Advance Side Path


Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the 2 open paths (the advance side path and retard side path).

NOTICE:

Cover the oil paths with a piece of cloth when applying air pressure to prevent oil from spraying.



v.
A198158C20
1.021,0.219 1.177,0.219 1.177,0.219 1.542,1.365 true 2.302,0.177 2.229,0.177 2.229,0.177 1.854,1.25 true 0.781,0.146 0.958,0.313 0.177,0.167 10 false *a 2.344,0.083 3.24,0.427 0.896,0.344 10 false *b 1.031,1.635 1.24,1.833 0.208,0.198 10 false *c 2.333,1.51 2.531,1.708 0.198,0.198 10 false *d
*a Retard Side Path
*b Advance Side Path
*c Hold pressure
*d Decompress


Check that the camshaft timing exhaust gear assembly turns in the retard direction when reducing the air pressure applied to the advance side path.

HINT:

This operation releases the lock pin and rotates the camshaft timing exhaust gear assembly rotates in the retard direction.



vi.

When the camshaft timing exhaust gear assembly moves to the most retarded position, release the air pressure from the advance side path, and then from the retard side path.

NOTICE:

Do not release the air pressure from the retard side path first. The camshaft timing exhaust gear assembly may abruptly shift in the advance direction and break the lock pin.




g.

Check for smooth rotation.

i.

Turn the camshaft timing exhaust gear assembly within its movable range (19.0 to 21.0°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the camshaft timing exhaust gear assembly turns smoothly.



h.

Check the lock at the most advanced position.

i.

Make sure that the camshaft timing exhaust gear assembly locks at the most advanced position.



i.

Remove the vinyl tape and rubber pieces from the No. 2 camshaft.


j.

Remove the bolt and camshaft timing exhaust gear assembly.


Hide 13521 9.INSPECT CRANKSHAFT TIMING SPROCKET

a.
A198159

Place the chain sub-assembly around the crankshaft timing sprocket.


b.

Using a vernier caliper, measure the crankshaft timing sprocket diameter with the chain sub-assembly.

Minimum Sprocket Diameter (with Chain):

59.94 mm (2.36 in.)


NOTICE:

The vernier caliper must be in contact with the chain rollers when measuring.


HINT:

If the diameter is less than the minimum, replace the chain sub-assembly and crankshaft timing sprocket.



Hide 13540 10.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A198160C08
1.542,0.958 2.042,0.094 2.042,0.094 2.25,0.094 true 2.75,1.427 2.99,1.427 false 3.021,1.354 3.25,1.552 0.229,0.198 10 false *a 2.292,0.021 2.521,0.219 0.229,0.198 10 false *b
*a Plunger
*b Stopper Plate


Turn the stopper plate counterclockwise to release the lock. Push the plunger and check that it moves smoothly.

If the plunger does not move smoothly, replace the No. 1 chain tensioner assembly.


Hide 13559 11.INSPECT CHAIN TENSIONER SLIPPER

a.
A198161C08
2.854,0.917 3.125,1.125 0.271,0.208 10 false *a
*a Depth


Measure the wear depth of the chain tensioner slipper.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the chain tensioner slipper.



Hide 13561 12.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A198162C10
2.792,0.865 3.021,1.083 0.229,0.219 10 false *a
*a Depth


Measure the wear depth of the No. 1 chain vibration damper.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the No. 1 chain vibration damper.



Hide 13566B 13.INSPECT TIMING CHAIN GUIDE

a.
A196926C10
3.021,1.76 3.302,1.99 0.281,0.229 10 false *a
*a Depth


Measure the wear depth of the timing chain guide.

Maximum Depth:

1.0 mm (0.0394 in.)


HINT:

If the depth is more than the maximum, replace the timing chain guide.



Hide 13620B 14.INSPECT NO. 1 BALANCE SHAFT THRUST CLEARANCE

a.
A196922

Using a dial indicator, measure the thrust clearance while moving the No. 1 balance shaft back and forth.

Standard Thrust Clearance:

0.05 to 0.09 mm (0.00197 to 0.00354 in.)


Maximum Thrust Clearance:

0.09 mm (0.00354 in.)


HINT:

If the thrust clearance is more than the maximum, replace the engine balancer assembly.



Hide 13620B 15.INSPECT NO. 2 BALANCE SHAFT THRUST CLEARANCE

a.
A198185

Using a dial indicator, measure the thrust clearance while moving the No. 2 balance shaft back and forth.

Standard Thrust Clearance:

0.05 to 0.09 mm (0.00197 to 0.00354 in.)


Maximum Thrust Clearance:

0.09 mm (0.00354 in.)


HINT:

If the thrust clearance is more than the maximum, replace the engine balancer assembly.



Hide 13620B 16.INSPECT BALANCE SHAFT BACKLASH

a.
A198163C08
1.323,0.302 1.563,0.5 0.24,0.198 10 false *a
*a Secure


Secure the No. 2 balance shaft in place, and then using a dial indicator, measure the backlash of the No. 1 balance shaft and No. 2 balance shaft as shown in the illustration.

Standard Backlash:

0.04 to 0.17 mm (0.00157 to 0.00669 in.)


Maximum Backlash:

0.17 mm (0.00669 in.)


NOTICE:

Measure at 3 or more areas around the circumference of the No. 1 balance shaft and No. 2 balance shaft.


HINT:

If the backlash is more than the maximum, replace the engine balancer assembly.



Hide 11101A 17.INSPECT CYLINDER HEAD SET BOLT

a.
A284095C11
2.271,0.344 2.583,0.5 0.313,0.156 10 false *a 1.396,1.5 1.719,1.75 0.323,0.25 10 false *b
*a Measurement Point
*b 106 mm (4.17 in.)


Using a vernier caliper, measure the diameter of the threads at the measurement point.

Standard Diameter:

10.85 to 11.00 mm (0.427 to 0.433 in.)


Minimum Diameter:

10.6 mm (0.417 in.)


Measurement Point (Distance from the Seat):

106 mm (4.17 in.)


HINT:
·

If the diameter is less than the minimum, replace the cylinder head set bolt with a new one. Failure to do so may lead to engine damage.

·

If there is any thread deformation, replace the cylinder head set bolt with a new one.




Hide 25051 18.INSPECT EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)

a.
A196896

Using a precision straightedge and feeler gauge, check the surface that contacts the cylinder head sub-assembly for warpage.

Maximum Warpage:

0.7 mm (0.0276 in.)


HINT:

If the warpage is more than the maximum, replace the exhaust manifold converter sub-assembly (TWC: Front Catalyst).