Home › Engine / Hybrid System › 2AR-FE (FUEL) › FUEL PUMP › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065325 2AR-FE FUEL _0328385 FUEL PUMP A

2AR-FE FUEL  FUEL PUMP  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.

Install a new fuel suction tube set gasket to the fuel tank assembly.


b.

Set the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



c.
A405923C01
1.052,1.25 0.719,0.26 0.719,0.26 2.281,0.906 true 0.302,2.615 0.958,2.615 true 0.51,0.146 0.688,0.302 0.177,0.156 10 true *a 0.125,2.521 0.302,2.677 0.177,0.156 10 true *a
*a Protrusion
V100135

Notch


Align the protrusions of the fuel suction tube with pump and gauge assembly with the notches in the fuel tank assembly.


Hide 77144 2.INSTALL FUEL PUMP GAUGE RETAINER

a.

Install the fuel pump gauge retainer.

i.

While pressing down on the fuel suction tube with pump and gauge assembly, temporarily install the fuel pump gauge retainer.


ii.
A405912C01
0.885,0.375 1.354,0.375 true 0.667,0.792 0.781,0.792 0.781,0.792 1.01,1.021 true 0.969,2.854 1.823,2.854 true 2.042,1.229 2.448,0.917 2.448,0.917 2.583,0.917 true 2.115,1.656 2.438,1.656 true 1.875,2.76 2.188,2.917 0.313,0.156 10 false *a 0.469,0.708 0.646,0.865 0.177,0.156 10 true *b 2.49,1.573 2.677,1.74 0.188,0.167 10 true *c 0.698,0.271 0.854,0.448 0.156,0.177 10 true *d 2.625,0.833 2.781,1.01 0.156,0.177 10 true *d
*a Insertion Point
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-14031  (09808-01030, 09808-01050)
09808-01071  

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



iii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iv.
A405924C01
0.698,0.448 0.813,0.448 0.813,0.448 1.115,0.99 true 1.042,0.146 1.177,0.146 1.177,0.146 1.458,0.583 true 2,1.24 2.365,1.052 2.365,1.052 2.51,1.052 true 2.146,1.396 2.49,1.396 true 2.604,3.323 2.844,2.917 2.844,2.917 2.958,2.917 true 2.25,3.427 2.625,3.958 2.625,3.958 2.76,3.958 true 2.813,3.875 2.99,4.052 0.177,0.177 10 true *a 3.01,2.833 3.323,2.99 0.313,0.156 10 false *b 0.51,0.354 0.688,0.521 0.177,0.167 10 true *c 2.542,1.313 2.74,1.479 0.198,0.167 10 true *d 0.875,0.052 1.073,0.229 0.198,0.177 10 true *e 2.552,0.969 2.75,1.146 0.198,0.177 10 true *e
*a Triangle Mark (Fuel Pump Gauge Retainer)
*b Triangle Mark (Fuel Tank Assembly)
*c SST (Handle)
*d SST (Plate)
*e SST (Bolt)
V100136

Front Side


Install SST (handle) to SST (plate).

SST
09808-14031  (09808-01010)
09808-01071  


v.

Using SST, rotate the fuel pump gauge retainer so that the triangle mark on the fuel pump gauge retainer is aligned with the triangle mark on the fuel tank assembly to install the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:
·

Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.

·

Make sure that the fuel suction tube set gasket does not come off.





b.

Engage the claw to install the No. 1 fuel tube clamp.


Hide 77209F 3.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Push the fuel tube joint onto the plug of the fuel suction plate sub-assembly, then install the tube joint clip.

A405925C01
4.021,1.479 5.302,2.719 1.281,1.24 5.646,1.469 6.927,2.708 1.281,1.24 5.052,0.281 5.302,0.281 false 5.792,0.604 6.042,0.604 false 5.573,0.75 5.938,0.75 5.938,0.75 5.938,0.854 false 5.552,0.854 6.115,0.854 false 4.615,1.083 4.771,1.083 4.771,1.083 4.906,0.75 false 4.802,1.917 5.052,1.917 false 6.448,2.01 6.698,2.01 false 6.219,1.948 6.365,1.646 6.365,1.646 6.458,1.646 true 4.604,2.042 4.865,2.354 4.865,2.354 4.979,2.354 true 2.458,1.24 2.615,0.688 2.615,0.688 2.76,0.688 true 2.729,1.427 3.094,1.427 true 4.448,1.01 4.76,1.167 0.313,0.156 10 false *1 6.104,0.521 6.417,0.677 0.313,0.156 10 false *2 2.802,0.604 3,0.781 0.198,0.177 10 true *3 4.885,0.188 5.198,0.344 0.313,0.156 10 false *a 6.167,0.771 6.479,0.927 0.313,0.156 10 false *b 4.115,1.51 4.427,1.667 0.313,0.156 10 false *c 5.708,1.5 6.021,1.656 0.313,0.156 10 false *d 5.031,2.26 5.344,2.417 0.313,0.156 10 false *e 5.104,1.813 5.417,1.969 0.313,0.156 10 false *2 6.698,1.906 7.01,2.063 0.313,0.156 10 false *2 3.125,1.344 3.302,1.51 0.177,0.167 10 true *2 6.521,1.552 6.833,1.708 0.313,0.156 10 false *e
*1 Fuel Suction Plate Sub-assembly *2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly - -
*a Fuel Tube Joint *b O-ring
*c Correct *d Incorrect
*e Collar - -
V100135

Insert
V100136

Insert


NOTICE:
·

Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.

·

Check that the fuel tube joint is securely inserted to the end.

·

Check that the tube joint clip is on the collar of the fuel tube joint.

·

After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.




Hide 4.CONNECT FUEL TANK EVAP/VENT TUBE SUB-ASSEMBLY

a.

Connect the fuel tank evap/vent tube sub-assembly to the fuel suction tube with pump and gauge assembly.

Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77754B 5.CONNECT CHARCOAL CANISTER OUTLET HOSE

a.

Connect the charcoal canister outlet hose to the fuel suction tube with pump and gauge assembly.


Hide 77026A 6.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A405907C01
1.635,2.073 1.813,2.24 0.177,0.167 10 true *a 2.021,2.26 2.333,2.417 0.313,0.156 10 false *b 1.906,2.5 2.219,2.656 0.313,0.156 10 false *c
*a Up
*b 120°
*c 60°


Connect the No. 1 fuel evaporation tube sub-assembly to the fuel suction tube with pump and gauge assembly and slide the clip to secure it.

HINT:

Engage the clip within the area shown in the illustration.



Hide 58325E 7.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Remove any remaining butyl tape from the rear floor service hole cover and vehicle body.


b.

Clean the installation surfaces of the rear floor service hole cover and vehicle body.


c.

Connect the fuel pump connector.


d.
A401707C01
0.802,0.302 0.958,0.302 0.958,0.302 1.125,0.5 true 0.615,0.219 0.792,0.385 0.177,0.167 10 true *a
*a Butyl Tape Adhesion Area


Install the rear floor service hole cover with new butyl tape.

NOTICE:

Securely install the rear floor service hole cover.



Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 72693 10.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 11.INSTALL REAR SEAT CUSHION ASSEMBLY

Hide 73350C 12.CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 13.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION