Home › Engine / Hybrid System › 2AR-FE (FUEL) › FUEL TANK › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065325 2AR-FE FUEL _0328386 FUEL TANK A

2AR-FE FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 77652A 1.INSTALL NO. 2 FUEL TANK CUSHION

a.

Install 2 new No. 2 fuel tank cushions to the fuel tank assembly.


Hide 77656B 2.INSTALL NO. 6 FUEL TANK CUSHION

a.

Install a new No. 6 fuel tank cushion to the fuel tank assembly.


Hide 77026A 3.INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Engage the clamp to install the No. 1 fuel evaporation tube sub-assembly to the fuel tank assembly.


Hide 77754B 4.INSTALL CHARCOAL CANISTER OUTLET HOSE

a.

Engage the clamp to install the charcoal canister outlet hose to the fuel tank assembly.


Hide 77209F 5.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Engage the clamp to install the fuel tank main tube sub-assembly to the fuel tank assembly.


Hide 77100 6.INSTALL FUEL TANK ASSEMBLY

CAUTION:
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.


a.

Set the fuel tank assembly on an engine lifter.

NOTICE:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.



b.
A406576N01
0.781,1.948 0.896,2.125 0.115,0.177 10 true 1 0.667,0.021 0.781,0.198 0.115,0.177 10 true 2 2.646,0 2.76,0.177 0.115,0.177 10 true 3 2.604,1.948 2.719,2.125 0.115,0.177 10 true 4

Using the engine lifter, slowly raise the fuel tank assembly, and then install the fuel tank assembly, No. 1 fuel tank band sub-assembly LH and No. 1 fuel tank band sub-assembly RH with the 4 bolts in the order shown in the illustration.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)

NOTICE:
·

Be careful not to drop the fuel tank assembly.

·

When installing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.




Hide 77209F 7.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Connect the fuel tank main tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77026A 8.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A405934C01
2.219,3.292 2.646,3.292 2.646,3.292 2.646,2.917 false 2.531,3.292 2.531,2.917 false 1.188,2.615 1.5,2.771 0.313,0.156 10 false *a 0.667,2.438 0.979,2.594 0.313,0.156 10 false *b 2.448,2.156 2.76,2.313 0.313,0.156 10 false *c 2.063,3.208 2.375,3.365 0.313,0.156 10 false *d
*a 120°
*b Up
*c 2.0 to 7.0 mm (0.0787 to 0.276 in.)
*d Paint Mark


Connect the No. 1 fuel evaporation tube sub-assembly to the fuel pipe and slide the clip to secure it.

HINT:

Engage the clip within the area shown in the illustration.



Hide 77213E 9.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A405932C01
0.688,3.115 1.021,3.115 true 1.083,3.229 1.333,3.229 true 0.813,4.177 0.885,4.177 0.885,4.177 1.042,4.104 true 1.177,4.094 1.385,4.333 1.385,4.333 1.448,4.333 true 1.375,2.385 1.563,2.552 0.188,0.167 10 false *a 0.958,2.219 1.135,2.385 0.177,0.167 10 true *b 2.906,3.896 3.219,4.052 0.313,0.156 10 false *c 0.656,4.083 0.844,4.24 0.188,0.156 10 true *d 1.5,4.25 1.813,4.406 0.313,0.156 10 false *e 1.719,3.698 2.031,3.854 0.313,0.156 10 false *f 0.521,3.01 0.719,3.219 0.198,0.208 10 false *g 1.375,3.146 1.688,3.302 0.313,0.156 10 false *h
*a 120°
*b Up
*c 0 to 3.0 mm (0 to 0.118 in.)
*d Clamp End
*e Stopper
*f +/- 2.0 mm (0.0787 in.)
*g Paint Mark (Fuel Tank To Filler Pipe Hose)
*h Protrusion (Fuel Tank Assembly)


Connect the fuel tank to filler pipe hose to the fuel tank assembly and tighten the clamp to secure it.

HINT:
·

Make sure the clamp and fuel tank to filler pipe hose are positioned within the area shown in the illustration.

·

Make sure that the clamp end is positioned within 2.0 mm (0.0787 in.) of the stopper.




Hide 10.CONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY

a.
A405930C01
0.333,2.823 0.646,2.979 0.313,0.156 10 false *a 0.823,1.958 1.031,2.115 0.208,0.156 10 true *b 2.448,3.188 2.76,3.344 0.313,0.156 10 false *c 2.396,1.99 2.604,2.146 0.208,0.156 10 true *d
*a 120°
*b Up
*c 0 to 3.0 mm (0 to 0.118 in.)
*d 2.0 to 7.0 mm (0.0787 to 0.276 in.)


Connect the fuel tank breather tube sub-assembly to the fuel tank filler pipe sub-assembly and tighten the clamp to secure it.

HINT:

Make sure the clamp and fuel tank breather tube sub-assembly are positioned within the area shown in the illustration.



Hide 77754B 11.CONNECT CHARCOAL CANISTER OUTLET HOSE

a.

Connect the charcoal canister outlet hose to the fuel tank filler pipe sub-assembly.


Hide 77641A 12.INSTALL NO. 1 FUEL TANK PROTECTOR

a.

Install the No. 1 fuel tank protector to the fuel tank assembly with the 4 clips.


Hide 58398F 13.INSTALL NO. 1 FLOOR UNDER COVER (w/ Cover)

Hide 58399D 14.INSTALL NO. 2 FLOOR UNDER COVER (w/ Cover)

Hide 17420 15.INSTALL CENTER EXHAUST PIPE ASSEMBLY

Hide 77020A 16.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 17.ADD FUEL