Home › Engine / Hybrid System › 2AR-FE (LUBRICATION) › OIL PUMP › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065329 2AR-FE LUBRICATION _0328503 OIL PUMP A

2AR-FE LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 11310 1.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.
A196858C01
0.271,1.177 0.583,1.375 0.313,0.198 10 false *1 1.271,1.396 1.427,1.667 0.156,0.271 10 true *1 2.583,0.625 2.896,0.823 0.313,0.198 10 true *2
*1 Oil Pump Gasket
*2 Oil Hole Cover Gasket


Apply a light coat of engine oil to 2 new oil pump gaskets and a new oil hole cover gasket.


b.

Install the 2 oil pump gaskets and oil hole cover gasket to the stiffening crankcase assembly.


c.
A196862C18
1.073,3.01 0.875,2.729 true 2.406,2.823 2.292,2.542 true 2.396,2.854 2.646,3.052 0.25,0.198 10 false *1 1.083,3.042 1.292,3.229 0.208,0.188 10 false *a
*1 Crankshaft Timing Sprocket
*a Drive Rotor Spline


Align the drive rotor spline and the crankshaft timing sprocket as shown in the illustration.


d.

Apply seal packing in a continuous line to the timing chain cover sub-assembly as shown in the following illustration.

A283978C09
5.563,1.635 5.208,1.635 true 5.927,3.302 5.729,3.302 5.729,3.302 5.385,3.552 true 6.135,5.469 5.917,5.469 5.917,5.469 5.552,5.729 true 2.385,7.292 2.031,7.292 false 5.188,3.031 5.5,3.188 0.313,0.156 10 false *a 4.333,3.708 4.646,3.865 0.313,0.156 10 false *b 5.302,5.188 5.615,5.344 0.313,0.156 10 false *c 5.583,1.094 5.833,1.271 0.25,0.177 10 false *i 5.615,1.573 5.865,1.74 0.25,0.167 10 false *h 5.813,4.115 6.042,4.302 0.229,0.188 10 false *g 5.99,3.24 6.906,3.438 0.917,0.198 10 false *j 4.25,2.854 5.167,3.052 0.917,0.198 10 false B - B, D - D 4.521,0.865 5.438,1.063 0.917,0.198 10 false A - A 5.01,6.302 5.188,6.479 0.177,0.177 10 false *j 6.198,5.417 6.438,5.573 0.24,0.156 10 false *k 3.844,5.969 4.156,6.125 0.313,0.156 10 false *b 4.198,5.125 5.115,5.323 0.917,0.198 10 false C - C 2.427,7.24 2.667,7.417 0.24,0.177 10 false *h 1.365,7.125 1.573,7.323 0.208,0.198 10 false *g 1.125,5.458 2.042,5.656 0.917,0.198 10 false E 0.26,0.125 1.177,0.323 0.917,0.198 10 false A - A 0.063,0.604 0.979,0.802 0.917,0.198 10 false B - B 0.417,1.615 0.802,1.771 0.385,0.156 10 true C - C 2.938,0.115 3.854,0.313 0.917,0.198 10 false A - A 2.438,0.677 3.354,0.875 0.917,0.198 10 false B - B 2.021,1.667 2.438,1.865 0.417,0.198 10 true C - C 2.104,2.427 3.021,2.625 0.917,0.198 10 false E 2.333,3.854 2.708,3.99 0.375,0.135 10 true D - D 0.323,3.854 1.24,4.052 0.917,0.198 10 false D - D 3.646,4.083 3.875,4.26 0.229,0.177 10 false *f 3.417,1.938 3.615,2.125 0.198,0.188 10 false *e 3.698,0.938 3.99,1.115 0.292,0.177 10 false *d 2,0.938 2.917,1.135 0.917,0.198 10 false E
*a 7.0 mm (0.276 in.) or more *b 3.0 mm (0.118 in.) or more
*c 13.0 mm (0.512 in.) or more *d 28 mm (1.10 in.)
*e 25 mm (0.984 in.) *f 26 mm (1.02 in.)
*g 3.0 mm (0.118 in.) *h 2.5 to 3.5 mm (0.0984 to 0.138 in.)
*i 2.5 mm (0.0984 in.) *j 5.0 mm (0.197 in.)
*k 7.0 mm (0.276 in.) - -


Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal Packing Application Chart:
Area Seal Packing Diameter (Round) Distance from Edge of Cover to Center of Seal Packing Seal Packing Application Length
Seal Packing Dimension (Flat)
Dashed Line 2.5 to 3.5 mm (0.0984 to 0.138 in.) 2.5 mm (0.0984 in.) -
-
A - A 2.5 to 3.5 mm (0.0984 to 0.138 in.) 2.5 mm (0.0984 in.) -
-
B - B 5.0 mm (0.197 in.) 3.0 mm (0.118 in.) 28 mm (1.10 in.)
7.0 mm (0.276 in.) or wider and 3.0 mm (0.118 in.) or thicker
C - C 7.0 mm (0.276 in.) 5.0 mm (0.197 in.) 25 mm (0.984 in.)
13.0 mm (0.512 in.) or wider and 3.0 mm (0.118 in.) or thicker
D - D 5.0 mm (0.197 in.) 3.0 mm (0.118 in.) 26 mm (1.02 in.)
7.0 mm (0.276 in.) or wider and 3.0 mm (0.118 in.) or thicker
E 2.5 to 3.5 mm (0.0984 to 0.138 in.) 3.0 mm (0.118 in.) -
-


NOTICE:
·

Clean the surfaces with non-residue solvent before applying seal packing.

·

Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

Do not add oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.




e.

Temporarily install the timing chain cover sub-assembly with the 17 bolts and 2 nuts.

A345984C02
0.573,0.167 0.885,0.365 0.313,0.198 10 false *a 3.552,0.135 3.865,0.333 0.313,0.198 10 false *b 1,0.26 1.156,0.458 0.156,0.198 10 false A 0.948,0.615 1.104,0.813 0.156,0.198 10 false A 1.052,1.333 1.208,1.531 0.156,0.198 10 false A 0.938,1.76 1.094,1.958 0.156,0.198 10 false A 1.031,2.021 1.188,2.219 0.156,0.198 10 false A 1.135,2.406 1.292,2.604 0.156,0.198 10 false A 1.271,2.552 1.427,2.75 0.156,0.198 10 false A 2.323,2.594 2.51,2.771 0.188,0.177 10 false A 2.802,2.344 2.958,2.542 0.156,0.198 10 false A 2.844,1.896 3,2.094 0.156,0.198 10 false A 2.74,1.573 2.896,1.771 0.156,0.198 10 false A 3.01,0.646 3.167,0.844 0.156,0.198 10 false A 1.094,0.823 1.25,1.021 0.156,0.198 10 false B 1.094,1.083 1.25,1.281 0.156,0.198 10 false B 2.833,1.052 2.99,1.25 0.156,0.198 10 false B 2.729,1.313 2.885,1.51 0.156,0.198 10 false B 5.813,1.313 5.969,1.51 0.156,0.198 10 false 1 6.198,0.281 6.354,0.479 0.156,0.198 10 false 5 6.115,0.625 6.271,0.823 0.156,0.198 10 false 6 5.906,1.083 6.063,1.281 0.156,0.198 10 false 3 5.823,1.583 5.979,1.781 0.156,0.198 10 false 7 5.927,1.885 6.083,2.083 0.156,0.198 10 false 8 5.854,2.406 6.01,2.604 0.156,0.198 10 false 9 5.635,2.469 5.833,2.677 0.198,0.208 10 false 10 5.427,2.594 5.615,2.792 0.188,0.198 10 false 11 4.26,2.573 4.479,2.771 0.219,0.198 10 false 12 4.104,2.417 4.354,2.625 0.25,0.208 10 false 13 4.042,2.01 4.229,2.177 0.188,0.167 10 false 14 3.979,1.708 4.24,1.906 0.26,0.198 10 false 15 4.104,1.354 4.333,1.552 0.229,0.198 10 false 16 4.146,1.094 4.302,1.292 0.156,0.198 10 false 2 4.135,0.823 4.292,1.021 0.156,0.198 10 false 4 3.979,0.594 4.219,0.771 0.24,0.177 10 false 17 4.031,0.229 4.323,0.427 0.292,0.198 10 false 18 2.25,1.792 2.406,1.99 0.156,0.198 10 false C 5.281,1.823 5.458,1.99 0.177,0.167 10 true 19
*a Torque *b Tightening Order
V100135

Bolt
V100136

Nut


Bolt Length:
Bolt Length Thread Diameter
(A) 30 mm (1.18 in.) 8 mm (0.315 in.)
(B) 35 mm (1.38 in.) 10 mm (0.394 in.)
(C) 45 mm (1.77 in.) 8 mm (0.315 in.)


NOTICE:

Make sure there is no oil on the bolts. If oil is found on any bolt, clean it before installation.



f.

Tighten the 17 bolts and 2 nuts in several steps, in the order shown in the illustration.

Torque:
Bolt (A), (C) and Nut : 21 N*m (214 kgf*cm, 15 ft.*lbf)
Bolt (B) : 55 N*m (561 kgf*cm, 41 ft.*lbf)


Hide 12315A 2.INSTALL ENGINE MOUNTING BRACKET RH

a.
A407983N01
1.781,1.729 1.938,1.927 0.156,0.198 10 true 1 0.896,0.531 1.052,0.729 0.156,0.198 10 true 2 2.271,0.833 2.427,1.031 0.156,0.198 10 true 3 1.156,1.552 1.313,1.75 0.156,0.198 10 true 4

Install the engine mounting bracket RH with the 4 bolts in the order shown in the illustration.

Torque:
Bolt (1), (2) and (3) : 55 N*m (561 kgf*cm, 41 ft.*lbf)
Bolt (4) : 21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

After applying seal packing to the timing chain cover sub-assembly, install the engine mounting bracket RH within 10 minutes.



Hide 16620 6.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11201 7.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 82121 9.INSTALL ENGINE WIRE

Hide 10.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE