Home › Engine / Hybrid System › 2GR-FKS (INTAKE / EXHAUST) › EXHAUST MANIFOLD
RM33A0E _51 Engine / Hybrid System _065336 2GR-FKS INTAKE / EXHAUST _0328629 EXHAUST MANIFOLD A

2GR-FKS INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 1.INSTALL STUD BOLT

HINT:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A408155

Using an E8 "TORX" socket wrench, install the 2 stud bolts to the exhaust manifold assembly LH (TWC: Front Catalyst).

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 17173 2.INSTALL EXHAUST MANIFOLD TO HEAD GASKET (for Bank 2)

a.

Install a new exhaust manifold to head gasket (for Bank 2) to the cylinder head sub-assembly.


Hide 17105 3.INSTALL EXHAUST MANIFOLD ASSEMBLY LH (TWC: Front Catalyst)

a.

Temporarily install the exhaust manifold assembly LH (TWC: Front Catalyst) with the 4 nuts.


b.

Temporarily install the No. 2 manifold stay to the exhaust manifold assembly LH (TWC: Front Catalyst) and cylinder block sub-assembly with the bolt and nut.


c.
A408153N01
2.094,0.208 2.25,0.406 0.156,0.198 10 true 1 1.094,1.563 1.25,1.76 0.156,0.198 10 true 2 2.24,1.552 2.396,1.75 0.156,0.198 10 true 3 1.073,0.292 1.229,0.49 0.156,0.198 10 true 4

Using a 12 mm deep socket wrench, tighten the 4 nuts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.
A408152C02
2.104,0.333 2.26,0.51 0.156,0.177 10 true 1 2.208,1.594 2.365,1.771 0.156,0.177 10 true 2
V100135

Bolt
V100136

Nut


Tighten the bolt and nut in the order shown in the illustration.

Torque:
Nut : 35 N*m (357 kgf*cm, 26 ft.*lbf)
Bolt : 34 N*m (347 kgf*cm, 25 ft.*lbf)


Hide 16281F 4.CONNECT NO. 5 WATER BY-PASS HOSE

a.

Engage the 2 clamps to connect the No. 5 water by-pass hose and No. 6 water by-pass hose to the hose clamp.


Hide 17168 5.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A408151N01
0.99,0.167 1.135,0.344 0.146,0.177 10 true 1 2.438,0.688 2.583,0.865 0.146,0.177 10 true 2 0.396,0.625 0.542,0.802 0.146,0.177 10 true 3

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold assembly LH (TWC: Front Catalyst) with the 3 bolts in the order shown in the illustration.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 11452 6.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 89467B 7.INSTALL AIR FUEL RATIO SENSOR (for Bank 2)

Hide 53295E 8.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 11209 9.INSTALL V-BANK COVER SUB-ASSEMBLY

Hide 17173 10.INSTALL EXHAUST MANIFOLD TO HEAD GASKET (for Bank 1)

a.

Install a new exhaust manifold to head gasket (for Bank 1) to the cylinder head sub-assembly RH.


Hide 17104 11.INSTALL EXHAUST MANIFOLD ASSEMBLY RH (TWC: Front Catalyst)

a.

Temporarily install the exhaust manifold assembly RH (TWC: Front Catalyst) with the 4 nuts.


b.
A408149N01
2.24,0.115 2.396,0.302 0.156,0.188 10 true 1 1.042,1.49 1.188,1.656 0.146,0.167 10 true 2 2.313,1.51 2.469,1.688 0.156,0.177 10 true 3 1.729,0.073 1.885,0.25 0.156,0.177 10 true 4

Using a 12 mm deep socket wrench, tighten the 4 nuts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17167 12.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A408148C01
2.51,0.594 3.073,0.792 0.563,0.198 10 true 1 (*a), 4 1.719,0.469 1.896,0.625 0.177,0.156 10 true 2 0.969,0.521 1.146,0.677 0.177,0.156 10 true 3
*a Temporarily Tighten


Install the No. 1 exhaust manifold heat insulator to the exhaust manifold assembly (TWC: Front Catalyst) with the 3 bolts in the order shown in the illustration.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 89467C 13.INSTALL AIR FUEL RATIO SENSOR (for Bank 1)

Hide 17410 14.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.

Install 3 new gaskets to the front exhaust pipe assembly (TWC: Rear Catalyst).


b.

Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust pipe support.


c.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) with 4 new bolts and 4 new nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


d.

Engage the 2 wire harness clamps.


e.

Connect the 2 heated oxygen sensor connectors.


Hide 17584B 15.INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Lower Side)

Hide 52239B 16.INSTALL BODY MOUNTING PLATE

Hide 51441 18.INSTALL NO. 1 ENGINE UNDER COVER

Hide 53852K 19.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851M 20.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH