Home › Engine / Hybrid System › 2AR-FE (INTAKE / EXHAUST) › INTAKE MANIFOLD › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065327 2AR-FE INTAKE / EXHAUST _0328637 INTAKE MANIFOLD A

2AR-FE INTAKE / EXHAUST  INTAKE MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17111 1.INSTALL INTAKE MANIFOLD

a.

Install the wire harness clamp bracket to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.
A292928C02
0.854,1.719 0.99,1.719 0.99,1.719 1.208,1.438 true 0.677,1.625 0.99,1.781 0.313,0.156 10 *a
*a Black


Connect the 2 vacuum hoses and check that the No. 1 check valve is installed as shown in the illustration.


c.

w/ TCV:

i.

Check the 4 tumble control valves (TCV).

NOTICE:

The 4 tumble control valves (TCV) may be damaged if they are not closed before installing the intake manifold.


HINT:

Apply battery voltage to the terminals of the intake air control valve actuator (for TCV) to operate the motor and close the 4 tumble control valves (TCV).

Click hereEngine / Hybrid System>2AR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION




d.

Install a new intake manifold to head gasket to the intake manifold.


e.

Temporarily install the intake manifold to the cylinder head sub-assembly with the 6 bolts.


f.
A381763C02
0.083,0.083 0.427,0.458 0.344,0.375 12 false *A 0.083,2.406 0.406,2.708 0.323,0.302 12 false *B 1.771,0.49 1.927,0.708 0.156,0.219 10 true 1 1.792,2.625 1.979,2.833 0.188,0.208 10 false 1 1.01,0.208 1.167,0.406 0.156,0.198 10 false 2 1.031,2.375 1.188,2.573 0.156,0.198 10 false 2 2.51,0.188 2.667,0.385 0.156,0.198 10 false 3 2.51,2.354 2.667,2.552 0.156,0.198 10 false 3 3.167,3.594 3.323,3.792 0.156,0.198 10 true 4 3.135,1.448 3.292,1.646 0.156,0.198 10 true 4 0.323,3.198 0.458,3.406 0.135,0.208 10 true 5 0.354,0.76 0.49,0.969 0.135,0.208 10 false 5 0.531,2.188 0.667,2.396 0.135,0.208 10 false 6 0.542,4.344 0.677,4.552 0.135,0.208 10 false 6
*A w/o TCV
*B w/ TCV


Tighten the 6 bolts in the order shown in the illustration.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


g.

w/ TCV:

i.
A407097C01
0.052,0.135 0.365,0.365 0.313,0.229 12 true *A 0.052,2.417 0.375,2.677 0.323,0.26 12 true *B
*A w/o TCV
*B w/ TCV


Connect the intake air control valve actuator (for TCV) connector.



h.

Engage the 2 wire harness clamps.


i.

Connect the engine wire with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


j.

Install the wire harness clamp bracket to the intake manifold with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


k.

Engage the 3 wire harness clamps.


l.

Connect the fuel vapor feed hose to the intake manifold and slide the clip to secure it.


Hide 44774 2.CONNECT UNION TO CONNECTOR TUBE HOSE (for LHD)

a.

Connect the union to connector tube hose to the intake manifold and slide the clip to secure it.


Hide 44773F 3.CONNECT UNION TO CHECK VALVE HOSE (for RHD)

a.

Connect the union to check valve hose to the intake manifold and slide the clip to secure it.


Hide 12262 4.CONNECT NO. 2 VENTILATION HOSE

a.

Connect the No. 2 ventilation hose to the intake manifold and slide the clip to secure it.


Hide 22030 5.INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY

Hide 23250 6.INSTALL FUEL INJECTOR ASSEMBLY

Hide 53607A 7.INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY (for LHD)

Hide 53607A 8.INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY (for RHD)

Hide 55708 9.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY