Home › Engine / Hybrid System › 2AR-FE (FUEL) › FUEL INJECTOR › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065325 2AR-FE FUEL _0328388 FUEL INJECTOR A

2AR-FE FUEL  FUEL INJECTOR  INSTALLATION  


PROCEDURE

Hide 23250 1.INSTALL FUEL INJECTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Apply a light coat of gasoline or spindle oil to new O-rings, and then install one to each fuel injector assembly.


b.

Apply a light coat of gasoline or spindle oil where the fuel delivery pipe contacts each O-ring.


c.
A405895C01
2.479,0.104 2.792,0.26 0.313,0.156 10 false *a
*a Turn
V100135

Push


While turning the fuel injector assembly left and right, install it to the fuel delivery pipe.

NOTICE:
·

Do not damage the fuel injector assembly or O-ring.

·

Make sure that the O-ring is not twisted or moved out of place when installing the fuel injector assembly.

·

After installing each fuel injector assembly, check that it turns smoothly. If not, replace the O-ring with a new one.



HINT:

Use the same procedure to install the other fuel injector assemblies.



Hide 23291 2.INSTALL INJECTOR VIBRATION INSULATOR

a.

Install 4 new injector vibration insulators to the cylinder head sub-assembly.


Hide 23891 3.INSTALL FUEL DELIVERY SPACER

a.
A405896C01
1.927,0.135 2.24,0.292 0.313,0.156 10 false *a 1.927,1.063 2.24,1.219 0.313,0.156 10 false *b
*a Fuel Delivery Pipe Side
*b Cylinder Head Sub-assembly Side


Install the 2 No. 1 fuel delivery spacers to the cylinder head sub-assembly.

NOTICE:

Install the No. 1 delivery pipe spacers in the correct direction.



Hide 23814B 4.INSTALL FUEL DELIVERY PIPE

a.

Install the fuel delivery pipe with the 4 fuel injector assemblies with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:
·

Be careful not to drop the fuel injector assemblies when installing the fuel delivery pipe.

·

Check that the fuel injector assemblies turn smoothly after installing the fuel delivery pipe.




Hide 82121 5.CONNECT ENGINE WIRE

a.
A405890C01
0,0 0,0 false
V100136

Bolt


Engage the clamp to connect the engine wire.


b.

Install the 2 wire harness brackets to the intake manifold with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the 4 fuel injector assembly connectors, throttle body with motor assembly connector, purge valve (purge VSV) connector and sensor wire connector.


Hide 17650 6.INSTALL VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)

Hide 23901 7.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Install the No. 1 fuel pipe clamp to the fuel tube connector and close the cover of the No. 1 fuel pipe clamp.


c.

Engage the clamp to connect the fuel tube sub-assembly to the fuel hose clamp.


Hide 17705 8.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 12601B 9.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 12.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION