Home › Engine / Hybrid System › 2AR-FE (ENGINE CONTROL) › SFI SYSTEM › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065323 2AR-FE ENGINE CONTROL _0329559 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor Circuit  


DESCRIPTION

The camshaft position sensor (for intake camshaft) (VV1 signal) consists of a magnet and MRE (Magneto Resistance Element).

The intake camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

Then the ECM uses this data to control fuel injection duration, fuel injection timing and Variable Valve Timing (VVT) system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0340 Camshaft Position Sensor Circuit One of the following conditions is met:
·

Missing camshaft position sensor (for intake camshaft) signal despite crankshaft position sensor inputs normal at engine speed of 600 rpm or higher (1 trip detection logic).

·

No camshaft position sensor (for intake camshaft) signal to ECM at engine speed of 600 rpm or higher (1 trip detection logic).

·

No camshaft position sensor (for intake camshaft) signal to ECM while cranking (2 trip detection logic).


·

Open or short in camshaft position sensor (for intake camshaft) circuit

·

Camshaft position sensor (for intake camshaft)

·

Intake camshaft

·

Valve timing

·

ECM


Comes on DTC stored

A255508E20
0.052,0.031 0.656,0.188 0.604,0.156 10 5 V/DIV. 0.167,0.656 0.49,0.823 0.323,0.167 10 CH1 0.156,1.448 0.479,1.615 0.323,0.167 10 CH2 0.094,0.844 0.49,1.052 0.396,0.208 10 (VV1) 0.083,1.604 0.479,1.833 0.396,0.229 10 (EV1) 3.052,0.813 3.396,0.958 0.344,0.146 10 GND 3.052,1.573 3.396,1.719 0.344,0.146 10 GND 1.271,1.865 2.021,2.042 0.75,0.177 10 20 ms./DIV.

Reference: Inspection using an oscilloscope.

HINT:
·

The correct waveform is as shown.

·

VV1 stands for the camshaft position sensor (for intake camshaft) signal, and EV1 stands for the camshaft position sensor (for exhaust camshaft) signal.



ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


MONITOR DESCRIPTION

If no pulse signal is transmitted by the camshaft position sensor (for intake camshaft) despite the camshaft rotating, or if the rotation of the intake camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine.

9.

Idle the engine for 10 seconds or more [A].

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P0340.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.




WIRING DIAGRAM

A413227E01
2.031,0.438 2.323,0.708 0.292,0.271 10 false VC 2.302,0.427 2.458,0.625 0.156,0.198 10 false 3 1.917,0.958 2.448,1.313 0.531,0.354 10 false VVI+ 1.938,1.531 2.552,1.729 0.615,0.198 10 false VVI- 2.302,0.948 2.458,1.146 0.156,0.198 10 false 1 2.313,1.521 2.469,1.719 0.156,0.198 10 false 2 0.802,2.135 1.26,2.333 0.458,0.198 10 false C17 0.792,2.313 3.875,2.667 3.083,0.354 10 false Camshaft Position Sensor (for Intake Camshaft) 4.479,0.417 4.938,0.615 0.458,0.198 10 false 116 4.844,0.427 5.458,0.625 0.615,0.198 10 false VCV1 4.604,0.958 4.917,1.156 0.313,0.198 10 false 82 4.875,0.969 5.49,1.167 0.615,0.198 10 false VV1+ 4.51,1.5 4.969,1.698 0.458,0.198 10 false 115 4.865,1.5 5.479,1.698 0.615,0.198 10 false VV1- 4.969,2.26 5.406,2.531 0.438,0.271 10 false C58 5.344,2.271 5.823,2.552 0.479,0.281 10 false ECM 5.531,0.25 5.917,0.542 0.385,0.292 10 false 5 V 5.49,0.844 6.25,1.135 0.76,0.292 10 false 1.5 kΩ

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR
A376492C73
0.385,0.927 0.76,1.24 0.375,0.313 0.813,1.781 1.385,1.177 true 1.74,1.917 1.688,1.208 true 2.719,1.729 1.958,1.198 true 0.448,1.01 0.906,1.208 0.458,0.198 10 false C17 0.188,0.094 0.5,0.292 0.313,0.198 10 false *a 0.594,1.813 1.104,2.125 0.51,0.313 10 false VVI+ 1.594,1.927 2.208,2.125 0.615,0.198 10 false VVI- 2.635,1.781 2.948,1.979 0.313,0.198 10 false VC
*a Front view of wire harness connector
(to Camshaft Position Sensor (for Intake Camshaft))


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C17-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V
C17-1 (VVI+) - Body ground Ignition switch ON 3.0 to 5.0 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C17-3 (VC) - C17-1 (VVI+) Ignition switch off 1.425 to 1.575 kΩ
C17-2 (VVI-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))

NG

6.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
2.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))
A316078C01
2.469,0.604 2.781,0.76 0.313,0.156 10 false *a 0.448,2.646 0.76,2.844 0.313,0.198 10 false OK 0.479,0.635 0.792,0.833 0.313,0.198 10 false NG
*a Clearance


a.

Check the camshaft position sensor (for intake camshaft) installation condition.

OK:

Camshaft position sensor (for intake camshaft) is installed correctly.



Result:
Proceed to
OK
NG



OK

3.CHECK INTAKE CAMSHAFT (TIMING ROTOR)

NG

SECURELY REINSTALL CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

3.CHECK INTAKE CAMSHAFT (TIMING ROTOR)
a.

Check the timing rotor of the intake camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the intake camshaft.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

4.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

OK

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

NG

5.CHECK ENGINE MECHANICAL SYSTEM
5.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


HINT:

Perform "Inspection After Repair" after repairing or replacing the engine mechanical system.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C17-3 (VC) - C58-116 (VCV1) Always Below 1 Ω
C17-1 (VVI+) - C58-82 (VV1+) Always Below 1 Ω
C17-2 (VVI-) - C58-115 (VV1-) Always Below 1 Ω
C17-3 (VC) or C58-116 (VCV1) - Body ground and other terminals Always 10 kΩ or higher
C17-1 (VVI+) or C58-82 (VV1+) - Body ground and other terminals Always 10 kΩ or higher
C17-2 (VVI-) or C58-115 (VV1-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR