Home › Engine / Hybrid System › 2AR-FE (ENGINE CONTROL) › SFI SYSTEM › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065323 2AR-FE ENGINE CONTROL _0329559 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If both signals, which indicate where the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores this DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a) and (b) are met for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch ON
(b) STP signal is off when ST1- signal is off
·

Open or short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

A402115E05
0.552,3.969 1.24,4.292 0.688,0.323 10 false Battery 0.469,3 1.25,3.333 0.781,0.333 10 false FL MAIN 0.458,2.313 1.094,2.594 0.635,0.281 10 false J/B-B 1.667,2 3.281,2.396 1.615,0.396 10 false Instrument Panel Junction Block Assembly 0.917,0.625 1.229,0.823 0.313,0.198 10 false 3E 0.958,0.458 1.115,0.656 0.156,0.198 10 false 1 0.917,1.51 1.229,1.708 0.313,0.198 10 false 3B 0.948,1.333 1.104,1.531 0.156,0.198 10 false 3 1.375,1.813 1.688,2.01 0.313,0.198 10 false 3A 1.115,1.802 1.427,2 0.313,0.198 10 false 44 1.542,1.302 1.896,1.615 0.354,0.313 10 false AM2 1.76,1.76 2.458,2.042 0.698,0.281 10 false IG2-NO. 2 2.365,1.219 2.938,1.563 0.573,0.344 10 false ECU-IG2 NO. 3 3.188,1.51 3.5,1.708 0.313,0.198 10 false 3A 3.188,1.354 3.5,1.552 0.313,0.198 10 false 17 3.167,1.083 3.479,1.281 0.313,0.198 10 false 3C 3.177,0.906 3.49,1.104 0.313,0.198 10 false 15 3.167,0.635 3.479,0.833 0.313,0.198 10 false 3C 3.198,0.469 3.354,0.667 0.156,0.198 10 false 3 2.469,0.792 2.938,1.042 0.469,0.25 10 false STOP 3.177,2.729 3.49,2.927 0.313,0.198 10 false *1 3.646,3.333 3.958,3.531 0.313,0.198 10 false *2 1.635,3.198 2.021,3.49 0.385,0.292 10 false K62 1.938,3.208 3.438,3.635 1.5,0.427 10 false Certification ECU (Smart Key ECU Assembly) 2.885,2.729 3.198,2.927 0.313,0.198 10 false 17 2.49,2.823 2.948,3.104 0.458,0.281 10 false IG1D 3.135,3.865 3.292,4.063 0.156,0.198 10 false 8 1.958,3.885 2.115,4.083 0.156,0.198 10 false 7 2.146,3.865 2.604,4.063 0.458,0.198 10 false AM1 2.813,3.865 3.219,4.104 0.406,0.24 10 false IG1 1.271,2.875 1.583,3.073 0.313,0.198 10 false *2 2.052,4.396 3.646,4.771 1.594,0.375 10 false Ignition Switch Assembly 1.74,4.406 2.198,4.604 0.458,0.198 10 false K30 4.01,3.26 5.781,3.594 1.771,0.333 10 false *1: w/ Smart Entry and Start System 4.052,3.906 5.813,4.271 1.76,0.365 10 false *2: w/o Smart Entry and Start System 4.01,1.948 4.469,2.146 0.458,0.198 10 false A37 4.365,1.958 5.469,2.417 1.104,0.458 10 false Stop Light Switch Assembly 4.458,1.427 4.917,1.625 0.458,0.198 10 false GND 4.25,1.292 4.406,1.49 0.156,0.198 10 false 2 4.49,1.063 4.719,1.365 0.229,0.302 10 false B 4.25,0.948 4.458,1.24 0.208,0.292 10 false 6 4.5,0.646 4.781,1.01 0.281,0.365 10 false B 4.24,0.5 4.396,0.698 0.156,0.198 10 false 7 5.073,0.615 5.229,0.813 0.156,0.198 10 false L 5.354,0.49 5.583,0.813 0.229,0.323 10 false 3 5.073,1.417 5.229,1.615 0.156,0.198 10 false L 5.354,1.271 5.615,1.531 0.26,0.26 10 false 5 5.969,0.521 6.396,0.781 0.427,0.26 10 false STP 5.75,0.51 6.063,0.708 0.313,0.198 10 false 9 5.948,1.292 6.396,1.708 0.448,0.417 10 false ST1- 5.677,1.302 5.99,1.5 0.313,0.198 10 false 10 5.969,4.427 6.396,4.729 0.427,0.302 10 false A22 6.313,4.427 6.771,4.625 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Stop light switch assembly conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch and ST1.

(e)

Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF


·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
A412754C01
0.417,0.927 0.781,1.229 0.365,0.302 2.708,1.75 2.385,1.156 true 0.208,0.135 0.521,0.333 0.313,0.198 10 false *a 0.479,0.99 0.938,1.188 0.458,0.198 10 false A37 2.656,1.802 2.813,2 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


a.

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

NG

13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
A412754C02
0.417,0.927 0.781,1.229 0.365,0.302 2.479,1.75 2.156,1.156 true 0.208,0.135 0.521,0.333 0.313,0.198 10 false *a 0.479,0.99 0.938,1.188 0.458,0.198 10 false A37 2.51,1.792 2.667,1.99 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


a.

Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-6 (B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY- STOP LIGHT SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)
A412755C01
4.125,0.75 4.458,0.979 0.333,0.229 5.573,1.51 6.125,0.74 true 6.51,1.521 6.198,0.75 true 1.229,1.438 1.542,1.635 0.313,0.198 10 false *a 2.938,1.417 3.25,1.615 0.313,0.198 10 false *b 4.281,0.073 4.594,0.271 0.313,0.198 10 false *c 4.156,0.771 4.615,0.969 0.458,0.198 10 false A22 5.385,1.552 5.844,1.75 0.458,0.198 10 false STP 6.344,1.531 6.958,1.729 0.615,0.198 10 false ST1-
*a Brake Pedal Depressed *b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)
- -


a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
A22-10 (ST1-) - Body ground Released 7.5 to 14 V
Depressed Below 1.5 V
A22-9 (STP) - Body ground Released Below 1.5 V
Depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-5 (L) - A22-10 (ST1-) Always Below 1 Ω
A37-3 (L) - A22-9 (STP) Always Below 1 Ω
A37-5 (L) or A22-10 (ST1-) - Body ground Always 10 kΩ or higher
A37-3 (L) or A22-9 (STP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY- STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Disconnect the stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-15 - A37-6 (B) Always Below 1 Ω
3C-15 or A37-6 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3B-3 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (POWER SOURCE)
A375649C03
0.615,1.146 0.948,1.396 0.333,0.25 0.271,0.125 0.583,0.323 0.313,0.198 10 false *a 0.719,1.198 1.031,1.396 0.313,0.198 10 false 3E
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


a.

Disconnect the instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3E-1 - Body ground Always 11 to 14 V



Result:
Result Proceed to
OK (w/ Smart Entry and Start System) A
OK (w/o Smart Entry and Start System) B
NG C



A

9.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

B

11.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - IGNITION SWITCH ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

9.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the instrument panel junction block assembly connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-17 - K62-17 (IG1D) Always Below 1 Ω
3A-17 or K62-17 (IG1D) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK SMART ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK SMART ENTRY AND START SYSTEM

OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

11.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - IGNITION SWITCH ASSEMBLY)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Disconnect the ignition switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-17 - K30-8 (IG1) Always Below 1 Ω
3A-17 or K30-8 (IG1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK ECM POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the instrument panel junction block assembly connector.


b.

Disconnect the stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-3 - A37-7 (B) Always Below 1 Ω
3C-3 or A37-7 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (POWER SOURCE)
A375649C03
0.615,1.146 0.948,1.396 0.333,0.25 0.271,0.125 0.583,0.323 0.313,0.198 10 false *a 0.719,1.198 1.031,1.396 0.313,0.198 10 false 3E
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


a.

Disconnect the instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3E-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)