Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM
RM33A0E _51 Engine / Hybrid System _065332 2GR-FKS ENGINE CONTROL _0329835 SFI SYSTEM J

2GR-FKS ENGINE CONTROL  SFI SYSTEM  ACIS Control Circuit  


DESCRIPTION

ACIS (Acoustic Control Induction System) controls the opening and closing the intake air control valve sub-assembly built into the intake air surge tank assembly to increase the intake efficiency according to the engine load.

When the engine speed is between 0 and 4300 rpm and the throttle valve opening angle is 30° or more, the ECM activates the No. 1 vacuum switching valve (for intake air control valve sub-assembly) which then applies vacuum from the vacuum pump assembly to the diaphragm actuator sub-assembly and closes the intake air control valve sub-assembly.

When the engine speed and/or throttle valve opening angle are not as specified above, the ECM deactivates the No. 1 vacuum switching valve (for intake air control valve sub-assembly), causing the intake air control valve sub-assembly to open.

A373331E01
0.615,2.208 1.01,0.802 1.01,0.802 1.125,0.802 false 1.344,1.656 1.344,1.125 1.344,1.125 1.458,1.125 false 4.74,3.5 4.719,2.219 4.719,2.219 4.875,2.229 false 5.229,6.281 5.104,6.281 5.104,6.281 5.094,5.188 false 2.813,3.135 2.635,3.135 2.635,3.135 1.688,2.74 true 0.625,3.688 0.625,3.531 0.625,3.531 1.125,2.854 false 0.646,6.698 0.958,5.313 0.958,5.313 1.083,5.313 false 1.344,6.156 1.333,5.771 1.333,5.771 1.438,5.771 false 3.198,2.396 3.51,1.573 3.51,1.573 3.625,1.573 false 3.198,6.885 3.26,5.823 3.26,5.823 3.365,5.823 false 0.719,8.021 0.719,7.885 0.719,7.885 1.188,7.354 false 2.865,7.75 2.698,7.74 2.698,7.74 1.677,7.271 true 0.031,0.271 0.938,0.542 0.906,0.271 10 false Engine Speed 1.219,0.24 3.042,0.573 1.823,0.333 10 false Throttle Valve Opening Angle 0.344,1.365 0.719,1.573 0.375,0.208 10 false ECM 1.156,0.719 3.146,1.104 1.99,0.385 10 false No. 1 Vacuum Switching Valve 1.5,1.042 3.073,1.354 1.573,0.313 10 false Vacuum Pump Assembly 2.906,3.073 4.219,3.479 1.313,0.406 10 false Intake Air Control Valve Sub-assembly 3.625,3.729 4.573,4.125 0.948,0.396 10 false Throttle Valve Opening Angle 4.302,4.25 4.625,4.49 0.323,0.24 10 false 30° 4.969,2.146 6.74,2.927 1.771,0.781 10 false Intake Air Control Valve Sub-assembly Closed (Vacuum Switching Valve: on) 4.479,5.333 4.917,5.552 0.438,0.219 10 false 0 rpm 6.083,5.344 6.74,5.635 0.656,0.292 10 false 4300 rpm 6.156,5.667 7.115,5.948 0.958,0.281 10 false Engine Speed 5.271,6.188 7.042,7.073 1.771,0.885 10 false Intake Air Control Valve Sub-assembly Open (Vacuum Switching Valve: off) 2.406,3.542 2.563,3.74 0.156,0.198 10 false 1 1.896,3.552 2.052,3.75 0.156,0.198 10 false 3 1.365,3.531 1.521,3.729 0.156,0.198 10 false 5 2.385,1.823 2.563,1.979 0.177,0.156 10 false 2 1.875,1.823 2.031,1.99 0.156,0.167 10 false 4 1.365,1.854 1.521,2.031 0.156,0.177 10 false 6 0.052,3.708 1.302,4.208 1.25,0.5 10 false Diaphragm Actuator Sub-assembly 0.052,4.75 1,5.031 0.948,0.281 10 false Engine Speed 1.177,4.76 3.01,5.073 1.833,0.313 10 false Throttle Valve Opening Angle 0.313,5.865 0.698,6.094 0.385,0.229 10 false ECM 1.156,5.229 3.104,5.51 1.948,0.281 10 false No. 1 Vacuum Switching Valve 1.479,5.688 3.115,6 1.635,0.313 10 false Vacuum Pump Assembly 3.688,1.5 5.229,1.833 1.542,0.333 10 false Throttle Position Sensor 3.417,5.76 4.979,6.021 1.563,0.26 10 false Throttle Position Sensor 0.031,8.042 1.292,8.521 1.26,0.479 10 false Diaphragm Actuator Sub-assembly 1.385,8.052 1.542,8.25 0.156,0.198 10 false 5 1.896,8.052 2.052,8.25 0.156,0.198 10 false 3 2.417,8.052 2.573,8.25 0.156,0.198 10 false 1 2.375,6.333 2.531,6.5 0.156,0.167 10 false 2 1.875,6.333 2.052,6.5 0.177,0.167 10 false 4 1.354,6.354 1.51,6.521 0.156,0.167 10 false 6 2.927,7.656 5.51,7.938 2.583,0.281 10 false Intake Air Control Valve Sub-assembly 0.625,6.948 1.125,7.146 0.5,0.198 10 false Suction

WIRING DIAGRAM

A410582E07
6.104,3.896 6.563,4.146 0.458,0.25 10 false ECM 5.667,3.323 6.125,3.573 0.458,0.25 10 false MREL 5.323,3.427 5.781,3.677 0.458,0.25 10 false A23 5.375,3.25 5.833,3.5 0.458,0.25 10 false 46 5.323,1.188 5.781,1.438 0.458,0.25 10 false C96 5.052,1.083 5.51,1.333 0.458,0.25 10 false 1 5.375,0.99 5.833,1.24 0.458,0.25 10 false 66 5.667,1.188 6.125,1.438 0.458,0.25 10 false ACIS 4.635,1.073 5.094,1.323 0.458,0.25 10 false ACIS 3.969,1.073 4.427,1.323 0.458,0.25 10 false +B 3.781,1.073 4.24,1.323 0.458,0.25 10 false 2 2.75,1.323 3.583,1.667 0.833,0.344 10 false EFI NO. 1 3.635,1.479 4.469,1.823 0.833,0.344 10 false C29 3.646,1.646 5.542,2.25 1.896,0.604 10 false No. 1 Vacuum Switching Valve (for Intake Air Control Valve) 1.594,1.552 2.052,1.802 0.458,0.25 10 false 1 2.281,1.552 2.74,1.802 0.458,0.25 10 false 2 2.271,1.073 2.729,1.323 0.458,0.25 10 false 5 1.583,1.073 2.042,1.323 0.458,0.25 10 false 3 1.573,1.979 2.833,2.313 1.26,0.333 10 false EFI-MAIN NO. 1 0.469,1.719 1.125,2.177 0.656,0.458 10 false EFI-MAIN NO. 1 0.469,2.625 1.729,2.958 1.26,0.333 10 false FL MAIN 0.615,3.365 1.875,3.698 1.26,0.333 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR INTAKE CONTROL)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Intake Control.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Intake Control
50004 372 47

e.

According to the display on the GTS, perform the Active Test to operate the No. 1 vacuum switching valve (for intake air control valve sub-assembly) and check for the operating sound of the intake air control valve sub-assembly in the intake air surge tank assembly.

OK:

Operating sounds can be heard.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT INTAKE AIR SURGE TANK ASSEMBLY (INTAKE AIR CONTROL VALVE SUB-ASSEMBLY OPERATION)
2.INSPECT INTAKE AIR SURGE TANK ASSEMBLY (INTAKE AIR CONTROL VALVE SUB-ASSEMBLY OPERATION)
a.

Inspect the intake air surge tank assembly (intake air control valve sub-assembly).

Click hereEngine / Hybrid System>2GR-FKS (INTAKE / EXHAUST)>INTAKE AIR CONTROL VALVE (for ACIS)>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT VACUUM HOSE SUB-ASSEMBLY (NO. 1 VACUUM SWITCHING VALVE (FOR INTAKE AIR CONTROL VALVE SUB-ASSEMBLY) - INTAKE AIR SURGE TANK ASSEMBLY)

NG

REPLACE INTAKE AIR SURGE TANK ASSEMBLY

3.INSPECT VACUUM HOSE SUB-ASSEMBLY (NO. 1 VACUUM SWITCHING VALVE (FOR INTAKE AIR CONTROL VALVE SUB-ASSEMBLY) - INTAKE AIR SURGE TANK ASSEMBLY)
a.

Check the vacuum hose sub-assembly (No. 1 vacuum switching valve (for intake air control valve sub-assembly) - intake air surge tank assembly) for looseness, disconnection and blockage.

OK:

No looseness, disconnection or blockage.



Result:
Proceed to
OK
NG



OK

4.CHECK VACUUM

NG

REPAIR OR REPLACE VACUUM HOSE SUB-ASSEMBLY

4.CHECK VACUUM
a.
A370148

Disconnect the vacuum hose sub-assembly from the No. 1 vacuum switching valve (for intake air control valve sub-assembly).


b.

Start the engine.


c.

Using your finger, confirm that the hose has suction.


Result:
Result Proceed to
Suction applied A
No suction B



A

5.INSPECT NO. 1 VACUUM SWITCHING VALVE (FOR INTAKE AIR CONTROL VALVE SUB-ASSEMBLY)

B

9.INSPECT VACUUM PUMP ASSEMBLY
5.INSPECT NO. 1 VACUUM SWITCHING VALVE (FOR INTAKE AIR CONTROL VALVE SUB-ASSEMBLY)
a.

Inspect the No. 1 vacuum switching valve (for intake air control valve sub-asembly).

Click hereEngine / Hybrid System>2GR-FKS (INTAKE / EXHAUST)>VACUUM SWITCHING VALVE(for ACIS)>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 VACUUM SWITCHING VALVE (FOR INTAKE AIR CONTROL VALVE SUB-ASSEMBLY))

NG

REPLACE NO. 1 VACUUM SWITCHING VALVE (FOR INTAKE AIR CONTROL VALVE SUB-ASSEMBLY)

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 VACUUM SWITCHING VALVE (FOR INTAKE AIR CONTROL VALVE SUB-ASSEMBLY))
a.
A373425C07
0.458,1.177 0.823,1.427 0.365,0.25 2.344,1.76 1.896,1.417 true 0.146,0.073 0.458,0.271 0.313,0.198 10 false *a 0.521,1.208 0.979,1.406 0.458,0.198 10 false C29 2.406,1.719 2.865,1.948 0.458,0.229 10 false +B
*a Front view of wire harness connector
(to No. 1 Vacuum Switching Valve (for Intake Air Control Valve Sub-assembly))


Disconnect the No. 1 vacuum switching valve (for intake air control valve sub-assembly) connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C29-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE (FOR INTAKE AIR CONTROL VALVE SUB-ASSEMBLY) - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - NO. 1 VACUUM SWITCHING VALVE (FOR INTAKE AIR CONTROL VALVE SUB-ASSEMBLY))
7.CHECK HARNESS AND CONNECTOR (NO. 1 VACUUM SWITCHING VALVE (FOR INTAKE AIR CONTROL VALVE SUB-ASSEMBLY) - ECM)
a.

Disconnect the No. 1 vacuum switching valve (for intake air control valve sub-assembly) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C29-1 (ACIS) - C96-66 (ACIS) Always Below 1 Ω
C29-1 (ACIS) or C96-66 (ACIS) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - NO. 1 VACUUM SWITCHING VALVE (FOR INTAKE AIR CONTROL VALVE SUB-ASSEMBLY))
a.

Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.


b.

Disconnect the No. 1 vacuum switching valve (for intake air control valve sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 1 relay) - C29-2 (+B) Always Below 1 Ω
5 (EFI-MAIN NO. 1 relay) or C29-2 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT VACUUM PUMP ASSEMBLY

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE VACUUM HOSE SUB-ASSEMBLY (NO. 1 VACUUM SWITCHING VALVE (FOR INTAKE AIR CONTROL VALVE SUB-ASSEMBLY) - VACUUM PUMP ASSEMBLY)

NG

REPLACE VACUUM PUMP ASSEMBLY