Home › Vehicle Interior › HEATING / AIR CONDITIONING › CONDENSER › 2017.12–2018.04
RM33A0E _58 Vehicle Interior _065387 HEATING / AIR CONDITIONING _0319111 CONDENSER A

HEATING / AIR CONDITIONING  CONDENSER  INSTALLATION  


PROCEDURE

Hide 88460 1.INSTALL COOLER CONDENSER ASSEMBLY

a.
E365854C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides and 2 claws to install the cooler condenser assembly as shown in the illustration.

NOTICE:

Do not damage the cooler condenser assembly or radiator assembly when installing the cooler condenser assembly.


HINT:

If a new cooler condenser assembly is installed, add compressor oil to the cooler condenser assembly as follows.


Capacity:

Add 40 cc (1.35 fl. oz)


Compressor Oil:

ND-OIL 8 or equivalent



Hide 53205 2.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY

Hide 88710E 3.CONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY

a.

Remove the vinyl tape from the open ends of the cooler condenser assembly and air conditioning tube and accessory assembly.


b.
E365851C01
2.083,1.833 2.083,1.448 false 1.417,1.833 1.417,1.583 false 1.198,1.417 0.615,1.167 0.615,1.167 1.198,0.917 true 2,1.844 2.313,2 0.313,0.156 10 false *1 1.323,1.844 1.635,2 0.313,0.156 10 false *2 0.417,1.052 0.729,1.208 0.313,0.156 10 false *a
*1 Air Conditioning Tube and Accessory Assembly
*2 Piping Clamp
*a Groove


Install a new piping clamp to the air conditioning tube and accessory assembly.

NOTICE:
·

Securely engage the inside step of the piping clamp in the air conditioning tube and accessory assembly groove.

·

Do not widen the opening of the piping clamp more than the diameter of the air conditioning tube and accessory assembly when installing it.

·

Do not install the piping clamp with the large diameter section in the wrong direction.




c.

Thoroughly coat 2 new O-rings and the contact surface of the air conditioning tube and accessory assembly with compressor oil.

Compressor Oil:

ND-OIL 8 or equivalent



d.

Install the 2 O-rings to the air conditioning tube and accessory assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



e.

Engage the cooler condenser assembly and air conditioning tube and accessory assembly.

E365852C01
5.354,2.521 5.823,2.271 true 5.833,2.146 6.146,2.302 0.313,0.156 10 false *a
*a Large Diameter Section of Piping Clamp - -


NOTICE:

Engage the parts by holding the pipe, not the piping clamp.



f.

Securely insert the piping clamp to the point where the large diameter section of the piping clamp is covered by the cooler condenser assembly.

HINT:
·

When inserting, make sure that a click sound is heard.

·

Check that the air conditioning tube and accessory assembly is securely installed by pulling it.




Hide 88711 4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the No. 1 cooler refrigerant discharge hose sub-assembly and the connecting part of the cooler condenser assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the No. 1 cooler refrigerant discharge hose sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose sub-assembly.

HINT:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the No. 1 cooler refrigerant discharge hose sub-assembly to the cooler condenser assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 16593B 5.INSTALL NO. 1 RADIATOR AIR GUIDE RH (w/o Air Cooled Transmission Oil Cooler)

a.
E365848C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide and claw to install the No. 1 radiator air guide RH as shown in the illustration.


b.

Install the clip.


c.

Connect the connector.


Hide 16593B 6.INSTALL NO. 1 RADIATOR AIR GUIDE RH (w/ Air Cooled Transmission Oil Cooler)

a.
E387131C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw to install the No. 1 radiator air guide RH as shown in the illustration.


b.

Install the clip.


Hide 16595B 7.INSTALL NO. 1 RADIATOR AIR GUIDE LH (w/o Air Cooled Transmission Oil Cooler)

a.
E365846C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide and claw to install the No. 1 radiator air guide LH as shown in the illustration.


b.

Install the clip.


Hide 16595B 8.INSTALL NO. 1 RADIATOR AIR GUIDE LH (w/ Air Cooled Transmission Oil Cooler)

a.
E387132C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw to install the No. 1 radiator air guide LH as shown in the illustration.


b.

Install the clip.


Hide 32913 12.INSTALL OIL COOLER BRACKET (w/ Air Cooled Transmission Oil Cooler)

Hide 88790B 13.INSTALL THERMISTOR ASSEMBLY (w/ Air Cooled Transmission Oil Cooler)

Hide 16691A 14.INSTALL FRONT RADIATOR SIDE AIR GUIDE PLATE RH

Hide 52131A 15.INSTALL FRONT BUMPER REINFORCEMENT

Hide 52611 16.INSTALL FRONT BUMPER ENERGY ABSORBER

Hide 15710 17.INSTALL OIL COOLER ASSEMBLY (w/ Air Cooled Transmission Oil Cooler)

Hide 19.INSTALL HEADLIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 20.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 53301 23.ADJUST HOOD SUB-ASSEMBLY