Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2017.12–2018.04
RM33A0E _58 Vehicle Interior _065379 THEFT DETERRENT / KEYLESS ENTRY _0328237 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Immobiliser System does not Operate Properly  


DESCRIPTION

The immobiliser function compares the ID code that is registered in the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

Before replacing the ECM, certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU)*, refer to Service Bulletin.

*: w/ ID Code Box


·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

If an immobiliser function or SFI system DTC is output, first perform troubleshooting for the immobiliser function or SFI system DTC.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
Powertrain > Engine > Trouble Codes
50001 372
Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.READ VALUE USING GTS (IMMOBILISER FUEL CUT STATUS, IMMOBILISER FUEL CUT)

B

2.READ VALUE USING GTS (IMMOBILISER FUEL CUT STATUS, IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine*1 or Engine and ECT*2 / Data List.

*1: except 2AR-FE

*2: for 2AR-FE



e.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status Status of immobiliser fuel cut OFF or ON - -
Powertrain > Engine > Data List
Tester Display
Immobiliser Fuel Cut Status
50003 372 65
Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser fuel cut OFF or ON - -
Powertrain > Engine and ECT > Data List
Tester Display
Immobiliser Fuel Cut
50003 234 505
OK:

OFF is displayed after the engine is started.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK WHETHER ENGINE STARTS
3.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Result Proceed to
OK A
NG (w/o ID Code Box) B
NG (w/ ID Code Box) C



A

B

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

C

8.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the A13 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A24*1, A23*2 or A22*3 ECM connector.

*1: for A25A-FKS

*2: for 2GR-FKS

*3: for 2AR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for A25A-FKS
Tester Connection Condition Specified Condition
A13-3 (EFII) - A24-25 (IMO) Always Below 1 Ω
A13-4 (EFIO) - A24-26 (IMI) Always Below 1 Ω
A13-3 (EFII) or A24-25 (IMO) - Other terminals and body ground Always 10 kΩ or higher
A13-4 (EFIO) or A24-26 (IMI) - Other terminals and body ground Always 10 kΩ or higher

for 2GR-FKS
Tester Connection Condition Specified Condition
A13-3 (EFII) - A23-45 (IMO) Always Below 1 Ω
A13-4 (EFIO) - A23-59 (IMI) Always Below 1 Ω
A13-3 (EFII) or A23-45 (IMO) - Other terminals and body ground Always 10 kΩ or higher
A13-4 (EFIO) or A23-59 (IMI) - Other terminals and body ground Always 10 kΩ or higher

for 2AR-FE
Tester Connection Condition Specified Condition
A13-3 (EFII) - A22-45 (IMO) Always Below 1 Ω
A13-4 (EFIO) - A22-28 (IMI) Always Below 1 Ω
A13-3 (EFII) or A22-45 (IMO) - Other terminals and body ground Always 10 kΩ or higher
A13-4 (EFIO) or A22-28 (IMI) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK ECM (TERMINAL EFIO AND EFII)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK ECM (TERMINAL EFIO AND EFII)
a.

Connect the A13 certification ECU (smart key ECU assembly) connector.


b.

Connect the A24*1, A23*2 or A22*3 ECM connector.

*1: for A25A-FKS

*2: for 2GR-FKS

*3: for 2AR-FE



c.

Using an oscilloscope, check the waveform.

B463110C01
1.948,0.156 2.396,0.406 0.448,0.25 2.438,2.042 2.573,2.042 2.573,2.042 2.573,1.01 true 2.781,2.042 2.646,2.042 2.646,2.042 2.646,1.01 true 3.115,4.115 3,4.115 3,4.115 3,3.656 false 3.51,6.146 3.396,6.146 3.396,6.146 3.396,5.688 false 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 2.042,0.198 2.354,0.396 0.313,0.198 10 false A13 2.073,1.948 2.5,2.156 0.427,0.208 10 false EFIO 2.833,1.938 3.146,2.135 0.313,0.198 10 false EFII 1.052,2.406 1.365,2.604 0.313,0.198 10 false *f 1.01,3.604 1.438,3.813 0.427,0.208 10 false GND 3.021,2.688 3.333,2.885 0.313,0.198 10 false *i 3.115,3.719 3.427,3.917 0.313,0.198 10 false *c 3.146,4.021 3.458,4.219 0.313,0.198 10 false *b 1.031,4.438 1.344,4.635 0.313,0.198 10 false *g 2.365,4.615 2.677,4.813 0.313,0.198 10 false *h 3.448,4.604 3.76,4.802 0.313,0.198 10 false *j 3.51,5.74 3.823,5.938 0.313,0.198 10 false *c 3.531,6.042 3.844,6.24 0.313,0.198 10 false *b 2.198,6.479 2.51,6.677 0.313,0.198 10 false *k 4.083,6.479 4.396,6.677 0.313,0.198 10 false *k 2.646,7.104 2.958,7.302 0.313,0.198 10 false *d 2.708,7.344 3.021,7.542 0.313,0.198 10 false *e 1.021,5.635 1.448,5.844 0.427,0.208 10 false GND 4.656,7.094 4.969,7.292 0.313,0.198 10 false *d 4.583,7.344 4.896,7.542 0.313,0.198 10 false *e
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Approximately 160 ms
*c Approximately 270 ms *d Approximately 40 ms
*e Approximately 60 ms *f Waveform (EFII)
*g Waveform (EFIO) *h Waveform A
*i Waveform B *j Waveform C
*k Waveform A (detail) - -


NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


OK:
Tester Connection Condition Tool Setting Specified Condition
A13-3 (EFII) - Body ground Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform (EFII))
A13-4 (EFIO) - Body ground Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform (EFIO))



Result:
Result Proceed to
Normal waveform A
Waveform A or C not output, or has abnormal wavelength or shape B
Waveform B not output, or has abnormal wavelength or shape C



A

6.REGISTER ECU COMMUNICATION ID

B

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

C

6.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER ENGINE STARTS
7.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

8.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
a.

Disconnect the K139 ID code box (immobiliser code ECU) connector.


b.

Disconnect the A23*1 or A22*2 ECM connector.

*1: for 2GR-FKS

*2: for 2AR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2GR-FKS
Tester Connection Condition Specified Condition
K139-3 (EFII) - A23-45 (IMO) Always Below 1 Ω
K139-4 (EFIO) - A23-59 (IMI) Always Below 1 Ω
K139-3 (EFII) or A23-45 (IMO) - Other terminals and body ground Always 10 kΩ or higher
K139-4 (EFIO) or A23-59 (IMI) - Other terminals and body ground Always 10 kΩ or higher

for 2AR-FE
Tester Connection Condition Specified Condition
K139-3 (EFII) - A22-45 (IMO) Always Below 1 Ω
K139-4 (EFIO) - A22-28 (IMI) Always Below 1 Ω
K139-3 (EFII) or A22-45 (IMO) - Other terminals and body ground Always 10 kΩ or higher
K139-4 (EFIO) or A22-28 (IMI) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK ECM (TERMINAL EFIO AND EFII)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK ECM (TERMINAL EFIO AND EFII)
a.

Connect the K139 ID code box (immobiliser code ECU) connector.


b.

Connect the A23*1 or A22*2 ECM connector.

*1: for 2GR-FKS

*2: for 2AR-FE



c.

Using an oscilloscope, check the waveform.

C379328C08
3.344,0.042 3.844,0.229 0.5,0.188 4.594,1.438 4.365,1.438 4.365,1.438 3.656,0.927 true 3.313,0.927 2.688,1.448 2.688,1.448 2.458,1.448 true 3,3.646 3,4.229 3,4.229 2.833,4.229 true 3.167,3.656 3.167,4.24 3.167,4.24 3.333,4.24 true 3.583,5.677 3.583,6.24 3.583,6.24 3.75,6.24 true 3.417,5.688 3.417,6.365 3.417,6.365 3.583,6.365 true 2.26,0.094 2.573,0.25 0.313,0.156 10 false *a 2.656,4.146 2.969,4.302 0.313,0.156 10 false *b 3.354,4.146 3.667,4.302 0.313,0.156 10 false *c 3.646,6.292 3.958,6.448 0.313,0.156 10 false *d 3.667,7.375 3.979,7.531 0.313,0.156 10 false *e 1.375,2.427 1.688,2.583 0.313,0.156 10 false *f 1.375,4.448 1.688,4.604 0.313,0.156 10 false *g 2.417,4.646 2.729,4.802 0.313,0.156 10 false *h 3.031,2.698 3.344,2.854 0.313,0.156 10 false *i 3.458,4.615 3.771,4.771 0.313,0.156 10 false *j 1.458,6.49 1.771,6.646 0.313,0.156 10 false *k 4.635,1.354 5.25,1.552 0.615,0.198 10 false EFII 3.781,6.156 4.094,6.313 0.313,0.156 10 false *c 3.74,7.125 4.052,7.281 0.313,0.156 10 false *d 1.854,7.135 2.167,7.292 0.313,0.156 10 false *d 1.948,7.385 2.26,7.542 0.313,0.156 10 false *e 1.042,5.646 1.406,5.906 0.365,0.26 10 false GND 1.042,3.604 1.406,3.865 0.365,0.26 10 false GND 2.115,1.365 2.729,1.563 0.615,0.198 10 false EFIO 3.427,0.063 4.042,0.26 0.615,0.198 10 false K139
*a Component with harness connected
(ID Code Box (Immobiliser Code ECU))
*b Approximately 160 ms.
*c Approximately 270 ms. *d Approximately 40 ms.
*e Approximately 60 ms. *f Waveform (EFII)
*g Waveform (EFIO) *h Waveform A
*i Waveform B *j Waveform C
*k Waveform A (detail) - -


NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


OK:
Tester Connection Condition Tool Setting Specified Condition
K139-3 (EFII) - Body ground Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform (EFII))
K139-4 (EFIO) - Body ground Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform (EFIO))



Result:
Result Proceed to
Normal waveform A
Waveform A or C not output, or has abnormal wavelength or shape B
Waveform B not output, or has abnormal wavelength or shape C



A

10.REGISTER ECU COMMUNICATION ID

B

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

C

10.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER ENGINE STARTS
11.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)