Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2018.04
RM33A0E _59 Vehicle Exterior _065394 WIPER / WASHER _0320457 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Washer Nozzle Heater Circuit  


DESCRIPTION

The main body ECU receives ambient air temperature information from the air conditioning amplifier assembly via CAN communication. The washer nozzle sub-assembly controls the main body ECU and operates the washer nozzle sub-assembly according to the ambient temperature.

WIRING DIAGRAM

E392122E02
0.927,0.156 2.76,0.354 1.833,0.198 10 false from Battery 0.385,0.656 3.448,0.854 3.063,0.198 10 false from IG1 NO. 1 Relay 2.01,0.333 3.698,0.531 1.688,0.198 10 false WSH NZL HTR 1.969,0.813 3.958,1.01 1.99,0.198 10 false ECU-IG1 NO. 3 2.823,1 3.813,1.51 0.99,0.51 10 false WSH NZL HTR 4.74,0.573 5.354,0.771 0.615,0.198 10 false WHTR 5.031,1.229 6.698,1.958 1.667,0.729 10 false Main Body ECU (Multiplex Network Body ECU) 2.781,1.948 2.938,2.146 0.156,0.198 10 false B 2.542,1.948 2.698,2.146 0.156,0.198 10 false B 2.771,3.604 2.927,3.802 0.156,0.198 10 false E 2.542,3.604 2.698,3.802 0.156,0.198 10 false E 5.115,2.646 7.01,3.323 1.896,0.677 10 false f2 5.146,3.99 7.031,4.74 1.885,0.75 10 false f1 3.01,4.188 5.156,4.677 2.146,0.49 10 false Washer Nozzle Sub-wire 2.698,4.188 3.01,4.385 0.313,0.198 10 false fA1 2.313,3.604 2.469,3.802 0.156,0.198 10 false 1 3,3.604 3.156,3.802 0.156,0.198 10 false 1 2.313,1.948 2.469,2.146 0.156,0.198 10 false 2 3,1.948 3.156,2.146 0.156,0.198 10 false 2 4.448,0.573 4.76,0.771 0.313,0.198 10 false 13 5.042,1.083 5.5,1.281 0.458,0.198 10 false K51 2.906,0.563 3.063,0.76 0.156,0.198 10 false 2 2.906,0.094 3.063,0.292 0.156,0.198 10 false 5 3.552,0.083 3.708,0.281 0.156,0.198 10 false 3 3.552,0.573 3.708,0.771 0.156,0.198 10 false 1 5.104,2.802 7,3.479 1.896,0.677 10 false Washer Nozzle Sub-assembly LH 5.146,4.188 7,4.771 1.854,0.583 10 false Washer Nozzle Sub-assembly RH 4.948,1.948 5.104,2.146 0.156,0.198 10 false 2 4.958,3.292 5.115,3.49 0.156,0.198 10 false 2 4.958,2.25 5.115,2.448 0.156,0.198 10 false 1 4.958,3.604 5.115,3.802 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*1

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*2

*1: w/ Door Control Battery

*2: w/ Smart Entry and Start System




PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Disconnect the fA1 washer nozzle sub-wire connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Main Body / Active Test.


f.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Washer Nozzle Heater Function to operate the nozzle heater OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Washer Nozzle Heater
50004 123 73

g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
fA1-2 (B) - Body ground Active Test not being performed Below 1 V
Active Test being performed 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (WASHER NOZZLE SUB-WIRE - BODY GROUND)

NG

5.INSPECT WSH NZL HTR RELAY
2.CHECK HARNESS AND CONNECTOR (WASHER NOZZLE SUB-WIRE - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
fA1-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT WASHER NOZZLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT WASHER NOZZLE SUB-ASSEMBLY
a.

Remove the washer nozzle sub-assembly.

Click hereVehicle Exterior>WIPER / WASHER>WASHER NOZZLE>REMOVAL


b.

Inspect the washer nozzle sub-assembly.

Click hereVehicle Exterior>WIPER / WASHER>WASHER NOZZLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT WASHER NOZZLE SUB-WIRE

NG

REPLACE WASHER NOZZLE SUB-ASSEMBLY

4.INSPECT WASHER NOZZLE SUB-WIRE
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
fA1-2 (B) - f2-2 Always Below 1 Ω
fA1-2 (B) - f1-2 Always Below 1 Ω
fA1-2 (B), f2-2 or f1-2 - Body ground Always 10 kΩ or higher
fA1-1 (E) - f2-1 Always Below 1 Ω
fA1-1 (E) - f1-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE WASHER NOZZLE SUB-WIRE

5.INSPECT WSH NZL HTR RELAY
a.

Inspect the WSH NZL HTR relay.

Click hereVehicle Exterior>WIPER / WASHER>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WSH NZL HTR RELAY)

NG

REPLACE WSH NZL HTR RELAY

6.CHECK HARNESS AND CONNECTOR (POWER SOURCE - WSH NZL HTR RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (WSH NZL HTR relay) - Body ground Always 11 to 14 V
2 (WSH NZL HTR relay) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (WSH NZL HTR RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (WSH NZL HTR RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the K51 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (WSH NZL HTR relay) - K51-13 (WHTR) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (WSH NZL HTR RELAY - WASHER NOZZLE SUB-WIRE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (WSH NZL HTR RELAY - WASHER NOZZLE SUB-WIRE)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (WSH NZL HTR relay) - fA1-2 (B) Always Below 1 Ω
3 (WSH NZL HTR relay) or fA1-2 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR