Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065374 NAVIGATION / MULTI INFO DISPLAY _0328126 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15C0  GPS Antenna Connection Malfunction(short)  B15C1  GPS Antenna Connection Malfunction(break)  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly*2 or antenna divider*1.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 GPS Antenna Connection Malfunction(short)
·

Antenna divider malfunction*1

·

Navigation antenna malfunction*2


·

Antenna divider*1

·

Antenna cord sub-assembly (for antenna divider)*1

·

Navigation antenna assembly*2

·

Antenna cord sub-assembly (for navigation antenna)*2

·

Navigation ECU


B15C1 GPS Antenna Connection Malfunction(break)
·

Antenna divider power source malfunction*1

·

Navigation antenna power source malfunction*2


·

Antenna divider*1

·

Antenna cord sub-assembly (for antenna divider)*1

·

Navigation antenna assembly*2

·

Antenna cord sub-assembly (for navigation antenna)*2

·

Navigation ECU



*1: w/ Telematics Transceiver

*2: w/o Telematics Transceiver


WIRING DIAGRAM

w/ Telematics Transceiver
E388524E01
1.771,0.729 1.927,0.927 0.156,0.198 10 false 2 5.323,0.729 5.479,0.927 0.156,0.198 10 false 1 3.583,1.281 3.74,1.479 0.156,0.198 10 false * 0.917,1.313 1.073,1.51 0.156,0.198 10 false A 0.917,1.458 3.208,1.656 2.292,0.198 10 false Antenna Divider 5.438,1.479 7.135,1.823 1.698,0.344 10 false Navigation ECU 5.448,1.323 5.604,1.521 0.156,0.198 10 false B 2.042,2.177 5.354,2.406 3.313,0.229 10 false *: Antenna Cord Sub-assembly (for Antenna Divider)

w/o Telematics Transceiver
E362443E03
5.229,3.063 6.25,3.521 1.021,0.458 10 false Navigation ECU 0.583,1.26 2.625,1.677 2.042,0.417 10 false Navigation Antenna Assembly 0.417,3 4.021,3.229 3.604,0.229 10 false *: Antenna Cord Sub-assembly (for Navigation Antenna) 0.594,1.104 1.156,1.438 0.563,0.333 10 false A 5.24,2.896 5.802,3.229 0.563,0.333 10 false B 4.958,0.5 5.417,0.875 0.458,0.375 10 false 1 1.844,0.49 2.302,0.865 0.458,0.375 10 false 3 3.406,1.24 3.844,1.594 0.438,0.354 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the navigation ECU, always replace it with a new one. If a navigation ECU which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The navigation ECU may not operate normally.


·

Check that the antenna cord sub-assembly (for navigation antenna)*1 or antenna cord sub-assembly (for antenna divider)*2 is properly installed and does not have any sharp bends, pinching or loose connections before performing following procedure.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING

*1: w/o Telematics Transceiver

*2: w/ Telematics Transceiver



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Result Proceed to
OK A
NG (w/o Telematics Transceiver) B
NG (w/ Telematics Transceiver) C



A

B

2.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Navigation Antenna)

C

4.INSPECT ANTENNA DIVIDER
2.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Navigation Antenna)
a.

Remove the antenna cord sub-assembly (for navigation antenna).

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>ANTENNA CORD>REMOVAL


b.
E322997C03
0.5,1.188 0.917,1.438 0.417,0.25 0.656,3.479 1.073,3.729 0.417,0.25 1.927,3.76 2.344,3.344 false 1.854,1 2.271,0.583 false 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 2.354,3.177 2.667,3.375 0.313,0.198 10 false 1a 2.313,0.427 2.625,0.625 0.313,0.198 10 false 3a 0.656,1.229 0.969,1.427 0.313,0.198 10 false A 0.813,3.521 1.125,3.719 0.313,0.198 10 false B
*a Component without harness connected
(Antenna Cord Sub-assembly (for Navigation Antenna))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-3 - B-1 Always Below 1 Ω
A-3a - B-1a Always Below 1 Ω
A-3 or B-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION ANTENNA ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY (for Navigation Antenna)

3.INSPECT NAVIGATION ANTENNA ASSEMBLY

b.
E381436C05
1.219,1.177 1.615,0.771 false 1.115,1.198 1.427,1.396 0.313,0.198 10 false 3a 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Navigation Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 3a Always 50 to 500 Ω



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT ANTENNA DIVIDER
a.

b.
E241596C22
1.125,1.417 0.979,1.76 0.979,1.76 0.781,1.76 true 1.979,1.406 1.833,1.75 1.833,1.75 1.635,1.75 true 0.573,1.677 1,1.854 0.427,0.177 10 false 6a 1.438,1.656 1.865,1.833 0.427,0.177 10 false 2a 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Antenna Divider)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 6 Always 10 kΩ or higher
2 - 2a Always 243 to 267 Ω
6 - 6a Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Antenna Divider)

NG

5.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Antenna Divider)
a.

Remove the antenna cord sub-assembly (for antenna divider).

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL


b.
E372424C07
1.521,0.354 1.896,0.583 0.375,0.229 1.302,1.656 1.302,1.219 false 0.146,0.167 0.458,0.365 0.313,0.198 10 false *a 1.656,0.385 1.813,0.583 0.156,0.198 10 false A 1.24,1.667 1.552,1.865 0.313,0.198 10 false 2a
*a Component without harness connected
(Antenna Cord Sub-assembly (for Antenna Divider))


E279082C42
1.49,0.125 1.969,0.375 0.479,0.25 2.333,1.51 1.927,1.302 false 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 2.375,1.479 2.688,1.677 0.313,0.198 10 false 1a 1.677,0.177 2,0.375 0.323,0.198 10 false B
*a Component without harness connected
(Antenna Cord Sub-assembly (for Antenna Divider))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-1 Always Below 1 Ω
A-2a - B-1a Always Below 1 Ω
A-2 or B-1 - Body ground Always 10 kΩ or higher
A-2a or B-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE ANTENNA DIVIDER

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY (for Antenna Divider)

6.REPLACE ANTENNA DIVIDER
a.

Replace the antenna divider with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL


b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG