Home › Engine / Hybrid System › 6AR-FSE (ENGINE MECHANICAL) › ENGINE UNIT › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072202 6AR-FSE ENGINE MECHANICAL _0351458 ENGINE UNIT G

6AR-FSE ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13801 1.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A336660

Turn the roller by hand to check that it turns smoothly.

HINT:

If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.



Hide 13750 2.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the valve lash adjuster assembly free from dirt and foreign matter.

·

Only use clean engine oil.



a.

Place the valve lash adjuster assembly into a container filled with engine oil.

A293105C32
1.583,0.302 1.969,0.302 false 2.344,0.302 2.802,0.302 false 1.448,0.958 2.052,0.698 true 2.313,0.698 2.896,0.865 true 1.5,1.125 2.063,0.938 false 2.302,0.938 2.833,1.083 false 1.385,1.406 2.052,1.229 true 2.313,1.219 2.938,1.365 true 1.302,1.99 2.052,1.583 true 2.323,1.573 3.042,1.969 true 1.469,2.115 2.063,1.958 true 2.323,1.958 2.875,2.104 true 4.698,1.104 5.052,1.354 false 2.115,0.844 2.427,1.073 0.313,0.229 10 false *f 2.115,1.469 2.427,1.677 0.313,0.208 10 false *g 2.125,0.594 2.438,0.75 0.313,0.156 10 false *c 2.115,1.135 2.427,1.292 0.313,0.156 10 false *d 2.115,1.865 2.427,2.021 0.313,0.156 10 false *e 2.052,0.229 2.51,0.427 0.458,0.198 10 false SST 4.406,1.021 4.865,1.219 0.458,0.198 10 false SST 1.198,0.188 1.51,0.385 0.313,0.198 10 false *a 2.979,0.177 3.292,0.375 0.313,0.198 10 false *b
*a Correct *b Incorrect
*c Taper *d Low Pressure Chamber
*e High Pressure Chamber *f Plunger
*g Check Ball - -



b.

Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  


c.

Squeeze SST and the valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed the air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding air from the high-pressure chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding the air, remove SST. Then try to quickly and firmly press the plunger by hand.

OK:

Plunger is very difficult to move.


If the result is not as specified, replace the valve lash adjuster assembly.


Hide 3.INSPECT CAMSHAFT OIL CLEARANCE

a.

Clean the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap, No. 4 camshaft bearing cap, camshaft housing sub-assembly and camshaft journals.


b.

Place the camshaft and No. 2 camshaft on the camshaft housing sub-assembly.


c.
A337938C01
0.521,0.271 0.729,0.271 0.729,0.271 1.302,0.833 true 0.344,0.198 0.656,0.354 0.313,0.156 10 false *a
*a Plastigage


Lay a strip of Plastigage across each of the camshaft journals.


d.

Install the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY

NOTICE:

Do not turn the camshafts.



e.

Install the camshaft housing sub-assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY


f.

Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE MECHANICAL)>CYLINDER HEAD GASKET>REMOVAL


g.
A337939C01
0.448,0.229 0.625,0.229 0.625,0.229 1.281,0.885 true 0.417,3.875 0.219,3.51 0.219,3.51 0.417,3.219 true 1.01,3.229 1.781,2.406 1.781,2.406 2.719,3.208 true 0.99,3.885 1.885,4.427 1.885,4.427 2.698,3.865 true 1.573,3.208 1.781,2.427 1.781,2.427 2.135,3.219 true 1.573,3.875 1.896,4.427 1.896,4.427 2.135,3.885 true 0.281,0.146 0.594,0.302 0.313,0.156 10 false *a 0.042,3.427 0.354,3.583 0.313,0.156 10 false *b 1.719,2.24 2.031,2.396 0.313,0.156 10 false *c 1.833,4.438 2.146,4.594 0.313,0.156 10 false *c
*a Plastigage
*b No. 1 Journal
*c Other Journal


Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Specified Condition
Intake No. 1 journal 0.035 to 0.072 mm (0.00138 to 0.00283 in.)
Exhaust No. 1 journal 0.049 to 0.086 mm (0.00193 to 0.00339 in.)
Other journals 0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake No. 1 journal 0.085 mm (0.00335 in.)
Exhaust No. 1 journal 0.095 mm (0.00374 in.)
Other journals 0.085 mm (0.00335 in.)


If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the camshaft housing sub-assembly.


Hide 4.INSPECT CAMSHAFT THRUST CLEARANCE

a.

Clean the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap, No. 4 camshaft bearing cap, camshaft housing sub-assembly and camshaft journals.


b.

Place the camshaft and No. 2 camshaft on the camshaft housing sub-assembly.


c.

Install the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY


d.

Install the camshaft housing sub-assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY


e.
A337940

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard Thrust Clearance:
Item Specified Condition
Intake 0.060 to 0.155 mm (0.00236 to 0.00610 in.)
Exhaust 0.060 to 0.155 mm (0.00236 to 0.00610 in.)


Maximum Thrust Clearance:
Item Specified Condition
Intake 0.170 mm (0.00669 in.)
Exhaust 0.170 mm (0.00669 in.)


If the thrust clearance is more than the maximum, replace the camshaft housing sub-assembly. If the thrust surface is damaged, replace the camshaft.


Hide 13511 5.INSPECT CAMSHAFT

a.
A336661

Inspect the camshaft for runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the runout at the center journal.

Maximum Runout:

0.03 mm (0.00118 in.)


If the runout is more than the maximum, replace the camshaft.

HINT:

Check the camshaft oil clearance after replacing the camshaft.




b.
A336663

Inspect the cam lobes (for intake valve).

i.

Using a micrometer, measure the cam lobe height.

Standard Cam Lobe Height:

44.1823 to 44.2823 mm (1.73946 to 1.74339 in.)


Minimum Cam Lobe Height:

44.0323 mm (1.73355 in.)


If the cam lobe height is less than the minimum, replace the camshaft.



c.
A336667

Inspect the cam lobes (for fuel pump drive).

i.

Using a micrometer, measure the cam lobe height.

Standard Cam Lobe Height:

42.1698 to 42.2698 mm (1.66023 to 1.66416 in.)


Minimum Cam Lobe Height:

42.0198 mm (1.65432 in.)


If the cam lobe height is less than the minimum, replace the camshaft.



d.
A336665

Inspect the camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 34.449 to 34.465 mm (1.35626 to 1.35689 in.)
Other journals 22.959 to 22.975 mm (0.90390 to 0.90453 in.)


If the journal diameter is not as specified, check the camshaft oil clearance.



Hide 13512 6.INSPECT NO. 2 CAMSHAFT

a.
A336662

Inspect the No. 2 camshaft for runout.

i.

Place the No. 2 camshaft on V-blocks.


ii.

Using a dial indicator, measure the runout at the center journal.

Maximum Runout:

0.03 mm (0.00118 in.)


If the runout is more than the maximum, replace the No. 2 camshaft.

HINT:

Check the camshaft oil clearance after replacing the No. 2 camshaft.




b.
A336664

Inspect the cam lobes.

i.

Using a micrometer, measure the cam lobe height.

Standard Cam Lobe Height:

43.5253 to 43.6253 mm (1.71359 to 1.71753 in.)


Minimum Cam Lobe Height:

43.3753 mm (1.70769 in.)


If the cam lobe height is less than the minimum, replace the No. 2 camshaft.



c.
A336666

Inspect the camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 34.449 to 34.465 mm (1.35626 to 1.35689 in.)
Other journals 22.959 to 22.975 mm (0.90390 to 0.90453 in.)


If the journal diameter is not as specified, check the camshaft oil clearance.



Hide 13070A 7.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Install the camshaft timing exhaust gear assembly to the No. 2 camshaft.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE MECHANICAL)>CAMSHAFT>INSTALLATION


b.
A328748C03
0.604,0.948 1.521,0.948 true 2,1.083 2.917,1.083 true 1.708,3.667 2.625,3.667 true 1.979,3.854 2.896,3.854 true 1.906,4.26 2.823,4.26 true 0.5,4.24 1.417,4.24 true 0.469,3.854 1.385,3.854 true 2.688,3.594 3,3.75 0.313,0.156 10 false *a 0.438,0.875 0.75,1.031 0.313,0.156 10 false *b 2.948,1.01 3.26,1.167 0.313,0.156 10 false *c 0.313,3.781 0.625,3.938 0.313,0.156 10 false *d 0.323,4.167 0.635,4.323 0.313,0.156 10 false *e 2.948,3.792 3.26,3.948 0.313,0.156 10 false *d 2.865,4.188 3.177,4.344 0.313,0.156 10 false *e
*a Knock Pin
*b Advance Side Path
*c Retard Side Path
*d Open
*e Close
V100144

Rubber Piece
V100145

Vinyl Tape


Release the lock pin.

i.

Clean the camshaft journal with non-residue solvent.


ii.

Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.

HINT:

There are 4 oil paths in the grooves of the No. 2 camshaft. Plug 2 paths with rubber pieces.



iii.

Make a hole in the vinyl tape placed on the advance side path. Make a hole in the vinyl tape placed on the retard side path on the opposite side to that of the advance side path as shown in the illustration.


iv.
A328749C03
1.875,1.24 2.667,0.5 2.667,0.5 2.833,0.5 true 1.583,1.365 0.583,1.083 0.583,1.083 0.417,1.083 true 2.875,0.427 3.188,0.583 0.313,0.156 10 false *a 0.26,1 0.573,1.156 0.313,0.156 10 false *b
*a Advance Side Path
*b Retard Side Path


Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the 2 open paths (the advance side path and retard side path).

NOTICE:

Cover the paths with a piece of cloth when applying pressure to keep oil from spraying.



v.
A328750C03
0.417,1 0.583,1 0.583,1 1.594,1.375 true 2.833,0.583 2.667,0.583 2.667,0.583 1.875,1.25 true 2.865,0.51 3.177,0.667 0.313,0.156 10 false *a 0.26,0.917 0.573,1.073 0.313,0.156 10 false *b 0.531,1.635 0.844,1.792 0.313,0.156 10 false *c 2.802,1.583 3.115,1.74 0.313,0.156 10 false *d
*a Advance Side Path
*b Retard Side Path
*c Hold Pressure
*d Decompress


Check that the camshaft timing exhaust gear assembly turns in the retard direction when reducing the air pressure applied to the advance side path.

HINT:

The lock pin is released and the camshaft timing exhaust gear assembly turns in the retard direction.



vi.

When the camshaft timing exhaust gear assembly moves to the most retarded position, release the air pressure from the advance side path, and then from the retard side path.

NOTICE:

Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing exhaust gear assembly may abruptly shift in the advance direction and break the lock pin or other parts.




c.

Check for smooth rotation.

i.

Turn the camshaft timing exhaust gear assembly within its movable range (26.5 to 28.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the camshaft timing exhaust gear assembly turns smoothly.

NOTICE:

When the air pressure is released from the advance side path and then from the retard side path, the camshaft timing exhaust gear assembly automatically returns to the most advanced position due to the advance assist spring operation, and locks. Gradually release the air pressure from the retard side path before performing the smooth rotation check.




d.

Check the lock at the most advanced position.

i.

Make sure that the camshaft timing exhaust gear assembly locks at the most advanced position.



e.

Remove the vinyl tape and rubber pieces from the No. 2 camshaft.


f.

Remove the bolt and camshaft timing exhaust gear assembly from the No. 2 camshaft.


Hide 13506 8.INSPECT CHAIN SUB-ASSEMBLY

A386378C14
1.729,0.979 2.042,1.177 0.313,0.198 10 false *a 0.979,2.01 1.188,2.177 0.208,0.167 10 false 0 1.385,2 1.583,2.177 0.198,0.177 10 false 1 1.99,2.021 2.313,2.177 0.323,0.156 10 false 14 2.396,2.01 2.667,2.177 0.271,0.167 10 false 15
*a Measurement Area


a.

Using a spring scale, pull the chain sub-assembly with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 15 pins.

Maximum Chain Elongation:

137.7 mm (5.42 in.)


HINT:

Perform the measurement at 3 random places. Use the average of the measurements.


If the average elongation is more than the maximum, replace the chain sub-assembly.


Hide 13521 9.INSPECT CRANKSHAFT TIMING SPROCKET

a.
A198159

Place the chain sub-assembly around the crankshaft timing sprocket.


b.

Using a vernier caliper, measure the crankshaft timing sprocket diameter with the chain sub-assembly.

Minimum Sprocket Diameter (with Chain Sub-assembly):

59.94 mm (2.36 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the crankshaft timing sprocket.


Hide 13540 10.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A198160C05
2.708,1.302 2.969,0.885 2.969,0.885 3.083,0.885 false 0.656,0.427 0.813,0.427 0.813,0.427 1.479,0.99 true 3.135,0.802 3.333,1 0.198,0.198 10 false *a 0.479,0.344 0.792,0.542 0.313,0.198 10 false *b
*a Plunger
*b Stopper Plate


Move the stopper plate counterclockwise to release the lock. Push the plunger and check that it moves smoothly.

If the plunger does not move smoothly, replace the No. 1 chain tensioner assembly.


Hide 13559 11.INSPECT CHAIN TENSIONER SLIPPER

a.
A337188C01
2.854,0.948 3.167,1.104 0.313,0.156 10 false *a
*a Depth


Measure the wear depth of the chain tensioner slipper.

Maximum Depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the chain tensioner slipper.


Hide 13561 12.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A337279C01
3.073,0.906 3.385,1.063 0.313,0.156 10 false *a
*a Depth


Measure the wear depth of the No. 1 chain vibration damper.

Maximum Depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the No. 1 chain vibration damper.


Hide 13566B 13.INSPECT TIMING CHAIN GUIDE

a.
A337280C01
3.021,0.927 3.333,1.083 0.313,0.156 10 false *a
*a Depth


Measure the wear depth of the timing chain guide.

Maximum Depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the timing chain guide.


Hide 14.INSPECT NO. 1 BALANCE SHAFT THRUST CLEARANCE

a.
A196922

Using a dial indicator, measure the thrust clearance while moving the No. 1 balance shaft back and forth.

Standard Thrust Clearance:

0.05 to 0.09 mm (0.00197 to 0.00354 in.)


Maximum Thrust Clearance:

0.09 mm (0.00354 in.)


If the thrust clearance is more than the maximum, replace the engine balancer assembly.


Hide 15.INSPECT NO. 2 BALANCE SHAFT THRUST CLEARANCE

a.
A198185

Using a dial indicator, measure the thrust clearance while moving the No. 2 balance shaft back and forth.

Standard Thrust Clearance:

0.05 to 0.09 mm (0.00197 to 0.00354 in.)


Maximum Thrust Clearance:

0.09 mm (0.00354 in.)


If the thrust clearance is more than the maximum, replace the engine balancer assembly.


Hide 16.INSPECT BALANCE SHAFT BACKLASH

a.
A198163C10
1.271,0.281 1.458,0.448 0.188,0.167 10 false *a
*a Secure


Secure the No. 2 balance shaft in place, and then using a dial indicator, measure the backlash of the No. 1 balance shaft and No. 2 balance shaft as shown in the illustration.

Standard Backlash:

0.04 to 0.17 mm (0.00157 to 0.00669 in.)


Maximum Backlash:

0.17 mm (0.00669 in.)


NOTICE:

Measure at 3 or more areas around the circumference of the No. 1 balance shaft and No. 2 balance shaft.


If the backlash is more than the maximum, replace the engine balancer assembly.


Hide 11101A 17.INSPECT CYLINDER HEAD SET BOLT

a.
A284095C12
2.271,0.344 2.583,0.5 0.313,0.156 10 false *a 1.417,1.51 1.927,1.74 0.51,0.229 10 false *b
*a Measurement Point
*b 106 mm


Using a vernier caliper, measure the diameter of the threads at the measurement point.

Standard Diameter:

10.85 to 11.00 mm (0.427 to 0.433 in.)


Minimum Diameter:

10.6 mm (0.417 in.)


Measurement Point (Distance from the Seat):

106 mm (4.17 in.)


HINT:
·

If the diameter is less than the minimum, replace the cylinder head set bolt with a new one. Failure to do so may lead to engine damage.

·

If there is any thread deformation, replace the cylinder head set bolt with a new one.




Hide 25051 18.INSPECT EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)

a.
A336668

Using a precision straightedge and feeler gauge, measure the warpage of the surface that contacts the cylinder head sub-assembly.

Maximum Warpage:

0.7 mm (0.0276 in.)


If the warpage is more than the maximum, replace the exhaust manifold converter sub-assembly (TWC: Front Catalyst).