Home › Engine / Hybrid System › 6AR-FSE (ENGINE MECHANICAL) › ENGINE UNIT › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072202 6AR-FSE ENGINE MECHANICAL _0351458 ENGINE UNIT A

6AR-FSE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STIFFENING CRANKCASE RING PIN

NOTICE:

It is not necessary to remove the stiffening crankcase ring pin unless it is being replaced.


a.
A336699C01
2.396,2.448 2.708,2.604 0.313,0.156 10 false *a
*a Protrusion Height


Using a plastic hammer, tap in 2 new stiffening crankcase ring pins until they stop.

Standard Protrusion Height:

4.3 to 5.3 mm (0.169 to 0.209 in.)



Hide 2.INSTALL STIFFENING CRANKCASE STUD BOLT

NOTICE:

If a stiffening crankcase stud bolt is deformed or its threads are damaged, replace it.


a.
A302211C02
2.219,1.406 2.063,1.208 false 2.281,1.396 2.594,1.552 0.313,0.156 10 false *a
*a Adhesive


Stiffening crankcase assembly front side:

i.

When reusing the stiffening crankcase stud bolt:

Apply adhesive to the threaded portion (stiffening crankcase assembly side) of the stud bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Install the stud bolt within 3 minutes of applying adhesive.




b.

Using E5 and E8 "TORX" socket wrenches, install the stiffening crankcase stud bolts.

A336698C01
0.26,1.177 4.438,2.76 4.177,1.583 0.771,0.115 1.083,0.271 0.313,0.156 10 false *a 0.313,1.208 0.625,1.365 0.313,0.156 10 false *b 2.167,0.969 2.323,1.167 0.156,0.198 10 false A 0.385,1.76 0.542,1.958 0.156,0.198 10 false B 1.313,2.594 1.469,2.792 0.156,0.198 10 false B 5.302,1.646 5.458,1.844 0.156,0.198 10 false B 5.313,0.021 5.469,0.219 0.156,0.198 10 false A 5.708,0.552 6.021,0.708 0.313,0.156 10 false *c 5.708,0.958 6.021,1.115 0.313,0.156 10 false *d 6.292,0.729 6.604,0.885 0.313,0.156 10 false *e 5.75,2.031 6.063,2.188 0.313,0.156 10 false *f 5.729,2.271 6.073,2.542 0.344,0.271 10 false *g 6.271,2.146 6.583,2.302 0.313,0.156 10 false *h 2.521,1.802 2.677,2 0.156,0.198 10 false B 3.563,1.344 3.719,1.542 0.156,0.198 10 false B 2.833,1.292 3.104,1.479 0.271,0.188 12 false *B 0.667,1.281 1.042,1.521 0.375,0.24 12 false *A
*A Type A *B Type B
*a Front Side *b Lower Side
*c 20 mm (0.787 in.) *d 13 mm (0.512 in.)
*e 35 mm (1.38 in.) *f 8.5 mm (0.335 in.)
*g 8.0 mm (0.315 in.) *h 18 mm (0.709 in.)


Torque:
Stud Bolt (A) : 9.5 N*m (97 kgf*cm, 84 in.*lbf)
Stud Bolt (B) : 4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 15679 3.INSTALL OIL FILTER BRACKET CLIP

a.
A337610

Install the oil filter bracket clip to the stiffening crankcase assembly.


Hide 13620B 4.INSTALL ENGINE BALANCER ASSEMBLY

a.
A198170C12
2.188,0.99 1.521,0.698 1.521,0.698 2.188,1.104 true 1.323,0.615 1.479,0.76 0.156,0.146 10 true *a
*a Alignment Mark


Check that the alignment marks of the balance shaft damper cover and No. 1 balance shaft driven gear are aligned.

If the alignment marks are not aligned, align them.

i.
A198171C16
0.896,1.729 1.177,1.729 1.177,1.729 1.625,1.25 true 2.208,1.292 2.729,1.813 2.729,1.813 2.292,1.167 true 1.01,1.969 1.219,1.969 1.219,1.969 1.719,1.552 true 0.719,1.646 0.906,1.802 0.188,0.156 10 false *a 0.813,1.885 1,2.063 0.188,0.177 10 false *b 2.656,1.823 2.896,2.052 0.24,0.229 10 true *c
*a No. 1 Balance Shaft Driven Gear
*b Balance Shaft Damper Cover
*c Alignment Mark


Place a wrench on the rear cutout part of the No. 2 balance shaft and secure the No. 2 balance shaft in place.


ii.

Rotate the No. 1 balance shaft driven gear of the No. 1 balance shaft counterclockwise to align the alignment mark of the No. 1 balance shaft driven gear with the alignment mark of the balance shaft damper cover.



b.
A338405N01
0.75,0.813 0.906,1.01 0.156,0.198 10 true 1 2.333,0.417 2.49,0.615 0.156,0.198 10 true 2 2.229,1.781 2.385,1.979 0.156,0.198 10 true 3

Install the engine balancer assembly to the stiffening crankcase assembly with the 3 bolts, and tighten the bolts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 11420 5.INSTALL STIFFENING CRANKCASE ASSEMBLY

a.
A339207C01
0.625,0.51 0.771,0.51 0.771,0.51 1.51,1.063 true 1.063,1.427 1.344,1.625 0.281,0.198 10 true 90° 0.448,0.427 0.76,0.625 0.313,0.198 10 false *1
*1 Crankshaft Pulley Key


Rotate the crankshaft clockwise so that the crankshaft pulley key is at the position 90° from the bottom as shown in the illustration.


b.
A258254C11
1.875,1.021 1.531,0.323 1.531,0.323 1.427,0.323 false 2.615,0.323 2.979,0.729 0.365,0.406 10 false A 1.146,3.521 1.281,3.688 0.135,0.167 10 false A 1.083,4.094 1.271,4.313 0.188,0.219 10 false *a 1.729,3.563 1.979,3.792 0.25,0.229 10 false *b 1.25,0.25 1.438,0.469 0.188,0.219 10 false *a
V100145

Stiffening Crankcase Assembly
V100146

Cylinder Block Sub-assembly
*a 2.5 to 3.5 mm
*b 7.0 to 9.0 mm


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Dimension:
Area Specified Condition
Continuous Line 2.5 to 3.5 mm (0.0984 to 0.138 in.)
Dashed Line 7.0 to 9.0 mm (0.276 to 0.354 in.) wide and 2.5 to 3.5 mm (0.0984 to 0.138 in.) thick


Application Length (A):

28 mm (1.10 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 15 minutes of applying seal packing.

·

Do not apply oil for at least 2 hours after the installation.




c.
A285537C07
1.417,0.979 1.208,0.302 1.208,0.302 1.99,0.99 false 1.083,0.125 1.396,0.281 0.313,0.156 10 *a
*a Cutout


Check that the rear cutouts are as shown in the illustration.


d.

Clean the bolts and the bolt holes.


e.
A198186C09
1.74,0.552 2.083,0.833 false 1.542,0.469 1.708,0.646 0.167,0.177 10 false *a
*a Adhesive


Apply adhesive to 3 or more threads at the tip of the bolts (A).

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



f.
A337930C01
0.5,0.333 0.656,0.531 0.156,0.198 10 false A 0.573,1.979 0.729,2.177 0.156,0.198 10 false A 2.042,2.146 2.198,2.344 0.156,0.198 10 false C 1.104,0.25 1.26,0.448 0.156,0.198 10 false D 1.948,0.323 2.104,0.521 0.156,0.198 10 false D 1.979,1.219 2.135,1.417 0.156,0.198 10 true D 1.323,2.146 1.479,2.344 0.156,0.198 10 false D 2.583,2.104 2.74,2.302 0.156,0.198 10 false B 3,2.042 3.156,2.24 0.156,0.198 10 false C 3.042,0.458 3.198,0.656 0.156,0.198 10 false C 2.469,0.292 2.625,0.49 0.156,0.198 10 false B 0.49,2.49 0.688,2.688 0.198,0.198 10 false 10 1.135,2.448 1.333,2.646 0.198,0.198 10 false 6 1.938,2.51 2.135,2.708 0.198,0.198 10 false 2 2.396,2.438 2.594,2.635 0.198,0.198 10 false 4 3.042,2.667 3.24,2.865 0.198,0.198 10 false 8 2.99,4.229 3.188,4.427 0.198,0.198 10 false 9 2.604,4.271 2.802,4.469 0.198,0.198 10 false 5 2.052,4.354 2.25,4.552 0.198,0.198 10 false 1 1.25,4.354 1.448,4.552 0.198,0.198 10 false 7 0.667,4.313 0.865,4.51 0.198,0.198 10 false 11 1.979,3.479 2.177,3.677 0.198,0.198 10 true 3 0.177,0.104 0.49,0.26 0.313,0.156 10 false *a 0.188,2.427 0.5,2.583 0.313,0.156 10 false *b
*a Bolt Type
*b Tightening Order


Temporarily install the stiffening crankcase assembly with the 11 bolts.

Bolt Length:
Item Length
Bolt (A) 65 mm (2.56 in.)
Bolt (B) 35 mm (1.38 in.)
Bolt (C) 125 mm (4.92 in.)
Bolt (D) 165 mm (6.50 in.)


HINT:

Apply adhesive to the bolts (A) before installation.



g.

Tighten the 11 bolts in the order shown in the illustration to install the stiffening crankcase assembly.

Torque:
Bolt (A) : 24 N*m (245 kgf*cm, 18 ft.*lbf)
except Bolt (A) : 43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 12121 6.INSTALL NO. 1 OIL PAN BAFFLE PLATE

a.
A337925N01
0.833,0.625 0.99,0.823 0.156,0.198 10 true 1 0.604,1.917 0.76,2.115 0.156,0.198 10 true 3 1.823,1.875 1.979,2.073 0.156,0.198 10 true 2 1.729,0.094 1.885,0.292 0.156,0.198 10 true 4

Install the No. 1 oil pan baffle plate and uniformly tighten the 4 bolts in several steps, in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install the clamp to the No. 1 oil pan baffle plate.


Hide 7.INSTALL OIL LEVEL SENSOR BRACKET

a.
A337924

Install the oil level sensor bracket to the stiffening crankcase assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 89491 8.INSTALL ENGINE OIL LEVEL SENSOR

Hide 15104 9.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new gasket.


b.
A337923C01
1.135,0.625 1.625,0.625 true 0.979,0.552 1.292,0.708 0.313,0.156 10 false *a 0.219,1.99 0.531,2.146 0.313,0.156 10 false 1 0.313,2.833 0.625,2.99 0.313,0.156 10 false 2 1.885,2.24 2.063,2.417 0.177,0.177 10 true 3
*a Protrusion


Align the protrusion of the gasket with the cutout of the oil strainer sub-assembly, and install the gasket to the oil strainer sub-assembly.


c.

Install the oil strainer sub-assembly with the 3 bolts in several steps, in the order shown in the illustration.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 12101 10.INSTALL OIL PAN SUB-ASSEMBLY

a.
A210205C01
1.365,1.656 1.844,1.656 false 1.208,1.583 1.469,1.813 0.26,0.229 10 false *a
*a Seal Packing


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Diameter:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 10 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




b.
A337281C02
1.938,0.083 2.292,0.354 0.354,0.271 10 false 1, 9 2.302,0.354 2.563,0.594 0.26,0.24 10 false 10 2.604,0.896 2.865,1.135 0.26,0.24 10 true 11 2.615,1.333 2.875,1.573 0.26,0.24 10 true 12 2.469,1.938 2.729,2.177 0.26,0.24 10 false 13 2.021,2.073 2.281,2.271 0.26,0.198 10 false 14 1.146,2.177 1.615,2.354 0.469,0.177 10 false 2, 15 0.729,2.104 0.927,2.313 0.198,0.208 10 false 3 0.406,1.833 0.604,2.042 0.198,0.208 10 false 4 0.354,1.198 0.552,1.406 0.198,0.208 10 false 5 0.667,0.719 0.823,0.917 0.156,0.198 10 true 6 0.938,0.542 1.073,0.74 0.135,0.198 10 true 7 1.115,0.24 1.354,0.479 0.24,0.24 10 false 8 1.708,0.51 1.865,0.708 0.156,0.198 10 true A 1.438,1.771 1.604,1.958 0.167,0.188 10 true A 0.719,4.292 0.917,4.5 0.198,0.208 10 false 3 0.406,4.01 0.604,4.219 0.198,0.208 10 false 4 0.365,3.396 0.563,3.604 0.198,0.208 10 false 5 0.625,2.896 0.781,3.094 0.156,0.198 10 true 6 0.927,2.708 1.063,2.906 0.135,0.198 10 true 7 1.115,2.438 1.354,2.677 0.24,0.24 10 false 8 2,2.375 2.354,2.646 0.354,0.271 10 false 1, 9 2.313,2.573 2.573,2.813 0.26,0.24 10 false 10 2.615,3.104 2.875,3.344 0.26,0.24 10 true 11 2.615,3.531 2.875,3.771 0.26,0.24 10 true 12 2.469,4.156 2.729,4.396 0.26,0.24 10 false 13 2.052,4.281 2.313,4.479 0.26,0.198 10 false 14 1.188,4.427 1.656,4.604 0.469,0.177 10 false 2, 15 1.438,3.979 1.604,4.167 0.167,0.188 10 true A 1.708,2.76 1.865,2.958 0.156,0.198 10 true A 0.229,0.167 0.604,0.406 0.375,0.24 12 false *A 0.229,2.51 0.604,2.75 0.375,0.24 12 false *B
*A Type A
*B Type B
V100135

Bolt
V100136

Nut


Install the oil pan sub-assembly with the 11 bolts and 2 nuts in several steps, in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

The bolt (A) and nut (A) are tightened twice.



Hide 12101A 11.INSTALL OIL PAN DRAIN PLUG

a.

Install a new gasket and the oil pan drain plug to the oil pan sub-assembly.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 15620 12.INSTALL OIL FILTER CAP ASSEMBLY

Hide 11445 14.INSTALL CYLINDER BLOCK WATER JACKET SPACER

a.
A336700

Install the cylinder block water jacket spacer to the cylinder block sub-assembly.


Hide 11101 16.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 11151A 17.INSTALL CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:

It is not necessary to remove the camshaft bearing cap setting ring pin unless it is being replaced.


a.
A336701C01
2.5,1.594 2.813,1.75 0.313,0.156 10 false *a
*a Protrusion Height


Using a plastic hammer, tap in 8 new camshaft bearing cap setting ring pins to the camshaft housing sub-assembly.

Standard Protrusion Height:

2.7 to 3.3 mm (0.106 to 0.130 in.)



Hide 11114A 18.INSTALL CAMSHAFT HOUSING STRAIGHT PIN

NOTICE:

It is not necessary to remove the camshaft housing straight pin unless it is being replaced.


a.
A336702C01
2.177,1.583 2.49,1.74 0.313,0.156 10 false *a
*a Protrusion Height


Using a plastic hammer, tap in 2 new camshaft housing straight pins to the camshaft housing sub-assembly.

Standard Protrusion Height:

5.0 to 7.0 mm (0.197 to 0.276 in.)



Hide 19.INSTALL CAMSHAFT HOUSING STUD BOLT

NOTICE:

If a camshaft housing stud bolt is deformed or its threads are damaged, replace it.


a.
A302211C02
2.219,1.406 2.063,1.208 false 2.281,1.396 2.594,1.552 0.313,0.156 10 false *a
*a Adhesive


When reusing the camshaft housing stud bolts:

i.

Apply adhesive to the threaded portion (camshaft housing sub-assembly side) of the stud bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Install the camshaft housing stud bolt within 3 minutes of applying adhesive.




b.
A336703C01
1.542,2.063 1.854,2.219 0.313,0.156 10 false *a 1.563,2.625 1.875,2.781 0.313,0.156 10 false *b 2.167,2.333 2.479,2.49 0.313,0.156 10 false *c
*a 20 mm (0.787 in.)
*b 13 mm (0.512 in.)
*c 35 mm (1.38 in.)


Using an E8 "TORX" socket wrench, install the camshaft housing stud bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 13716 20.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem cap ends.


b.

Install the 16 valve stem caps to the cylinder head sub-assembly.

NOTICE:

Do not drop the valve stem caps into the cylinder head sub-assembly.



Hide 13750 21.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

Inspect the 16 valve lash adjuster assemblies before installing them.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION


b.

Install the 16 valve lash adjuster assemblies to the cylinder head sub-assembly.

NOTICE:

Install each valve lash adjuster assembly to the same place it was removed from.



Hide 13801 22.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A337584C01
0.76,0.385 1.458,0.385 true 0.313,0.938 1.01,0.938 true 2.604,0.917 2.927,0.917 true 0.594,0.292 0.906,0.448 0.313,0.156 10 false *1 2.979,0.844 3.292,1 0.313,0.156 10 false *2 0.156,0.854 0.469,1.01 0.313,0.156 10 false *3
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap


Apply engine oil to the valve lash adjuster assembly tips and valve stem caps.


b.

Install the 16 No. 1 valve rocker arm sub-assemblies as shown in the illustration.


Hide 11811 23.INSTALL NO. 1 CAMSHAFT BEARING

a.
A337931C01
2.688,2.052 2.823,1.594 2.823,1.594 3.01,1.594 false 3.052,1.51 3.365,1.667 0.313,0.156 10 false *a 1.438,2.396 1.594,2.594 0.156,0.198 10 false A 2.969,2.375 3.125,2.573 0.156,0.198 10 false B
*a Vernier Caliper


Clean the No. 1 camshaft bearing.


b.

Install the No. 1 camshaft bearing to the No. 1 camshaft bearing cap.


c.

Using a vernier caliper, measure the distance between the No. 1 camshaft bearing cap edge and the No. 1 camshaft bearing edge.

Difference Between (A) and (B):

0 to 0.7 mm (0 to 0.0276 in.)



Hide 11821 24.INSTALL NO. 2 CAMSHAFT BEARING

a.

Clean the No. 2 camshaft bearing.


b.

Install the No. 2 camshaft bearing to the camshaft housing sub-assembly.


c.
A198177C15
0.917,1.313 0.823,1.313 0.823,1.313 0.74,2.531 false 0.969,1.229 1.156,1.417 0.188,0.188 10 false *a
*a Vernier Caliper


Using a vernier caliper, measure the distance between the camshaft housing sub-assembly edge and the No. 2 camshaft bearing edge.

Standard Distance:

1.15 to 1.85 mm (0.0453 to 0.0728 in.)



Hide 15678A 25.INSTALL OIL CONTROL VALVE FILTER

a.
A337607

Install the oil control valve filter to the No. 1 camshaft bearing cap.


Hide 13511 26.INSTALL CAMSHAFT

a.

Clean the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.


b.

Apply a light coat of engine oil to the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.


c.

Install the camshaft to the camshaft housing sub-assembly.

HINT:

Perform "Inspection After Repair" after replacing the camshaft.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 13512 27.INSTALL NO. 2 CAMSHAFT

a.

Clean the camshaft journals and camshaft housing sub-assembly.


b.

Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly.


c.

Install the No. 2 camshaft to the camshaft housing sub-assembly.

HINT:

Perform "Inspection After Repair" after replacing the No. 2 camshaft.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 28.INSTALL CAMSHAFT BEARING CAP

a.

Place the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap in their correct positions.


b.
A337605N02
0.052,1.719 0.333,1.969 0.281,0.25 10 false 11 0.052,1.021 0.208,1.219 0.156,0.198 10 false 9 0.021,0.344 0.292,0.594 0.271,0.25 10 false 10 0.646,0.958 0.802,1.156 0.156,0.198 10 false 5 1.26,0.927 1.385,1.094 0.125,0.167 10 false 1 1.833,0.969 1.99,1.167 0.156,0.198 10 false 3 2.448,0.979 2.604,1.177 0.156,0.198 10 false 7 2.708,0.135 2.865,0.333 0.156,0.198 10 true 8 2.104,0.135 2.26,0.333 0.156,0.198 10 true 4 1.521,0.125 1.76,0.323 0.24,0.198 10 true 2 0.896,0.135 1.135,0.333 0.24,0.198 10 true 6

Install the 11 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:

Make sure that the camshaft and No. 2 camshaft rotate smoothly after installing the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.



Hide 11103 29.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A337584C01
0.76,0.385 1.458,0.385 true 0.313,0.938 1.01,0.938 true 2.604,0.917 2.927,0.917 true 0.594,0.292 0.906,0.448 0.313,0.156 10 false *1 2.979,0.844 3.292,1 0.313,0.156 10 false *2 0.156,0.854 0.469,1.01 0.313,0.156 10 false *3
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap


Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


b.
A337899C01
1.635,1.177 1.979,0.458 1.979,0.458 2.188,0.458 false 1.24,0.177 1.552,0.333 0.313,0.156 10 false *b 1.51,2.708 1.823,2.865 0.313,0.156 10 false *c 2.229,0.375 2.542,0.531 0.313,0.156 10 false *a
*a Seal Packing
*b 2.5 to 3.5 mm (0.0984 to 0.138 in.)
*c 3.5 to 4.0 mm (0.138 to 0.157 in.)


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the camshaft housing sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.




c.
A337900C01
1.156,1.125 1.76,1.927 1.76,1.927 2.323,1.135 true 0.958,0.208 1.271,0.365 0.313,0.156 10 false *a 2.26,0.156 2.573,0.313 0.313,0.156 10 false *b 1.708,1.938 2.021,2.094 0.313,0.156 10 false *c
*a Approximately 17°
*b Approximately 2°
*c Knock Pin


Position the knock pins of the camshaft and No. 2 camshaft as shown in the illustration.


d.
A337603N02
2.385,1.958 2.656,2.156 0.271,0.198 10 false 20 2.667,1.958 2.958,2.156 0.292,0.198 10 false 11 0.021,1.677 0.313,1.927 0.292,0.25 10 false 14 0.031,0.927 0.271,1.177 0.24,0.25 10 false 13 0.063,0.438 0.313,0.667 0.25,0.229 10 false 15 1.063,0.063 1.219,0.26 0.156,0.198 10 false 9 0.771,1.958 1.01,2.177 0.24,0.219 10 false 19 1.063,1.958 1.219,2.156 0.156,0.198 10 false 8 0.688,0.604 0.896,0.802 0.208,0.198 10 true 7 1.24,0.604 1.448,0.802 0.208,0.198 10 true 1 1.604,0.052 1.76,0.25 0.156,0.198 10 false 3 2.135,0.052 2.292,0.25 0.156,0.198 10 false 6 2.625,0.052 3.115,0.313 0.49,0.26 10 false 12 3.24,0.854 3.427,1.073 0.188,0.219 10 false 18 3.208,1.271 3.427,1.469 0.219,0.198 10 false 16 3.219,1.771 3.427,1.969 0.208,0.198 10 false 17 2.146,1.958 2.302,2.156 0.156,0.198 10 false 5 1.615,1.958 1.771,2.156 0.156,0.198 10 false 2 1.823,0.635 2.031,0.833 0.208,0.198 10 true 4 2.396,0.635 2.604,0.833 0.208,0.198 10 true 10

Install the camshaft housing sub-assembly, and then install the 20 bolts in the order shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)

NOTICE:
·

Do not apply oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.

·

After installation, if the seal packing has seeped out, wipe it off.




Hide 15707H 30.INSTALL OIL PIPE SUB-ASSEMBLY

a.
A337599

Install the oil pipe sub-assembly to the No. 4 camshaft bearing cap with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13070A 31.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A337582C01
1.365,2.99 1.365,2.427 true 2.438,0.76 1.344,0.76 true 2.49,0.688 2.802,0.844 0.313,0.156 10 false *a 1.313,3 1.625,3.156 0.313,0.156 10 false *b
*a Knock Pin Hole
*b Knock Pin


Align and fit the knock pin of the No. 2 camshaft with the knock pin hole of the camshaft timing exhaust gear assembly.

NOTICE:

Be careful not to damage the contact surface of the camshaft timing exhaust gear assembly with the knock pin of the No. 2 camshaft.



b.
A328700C04
0.333,0.583 1,0.583 true 1.271,0.677 1.667,0.333 1.667,0.333 1.833,0.333 true 0.177,0.5 0.49,0.656 0.313,0.156 10 false *1 1.885,0.25 2.198,0.406 0.313,0.156 10 false *c 0.792,1.896 1.104,2.052 0.313,0.156 10 false *e 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 0.094,1.875 0.406,2.031 0.313,0.156 10 false *b 0.781,0.073 1.094,0.229 0.313,0.156 10 false *d
*1 Camshaft Timing Exhaust Gear Assembly
*a Incorrect
*b Correct
*c No. 2 Camshaft Flange
*d Gap
*e No Gap


Check that there is no gap between the camshaft timing exhaust gear assembly and No. 2 camshaft flange.


c.
A337598C01
1.969,0.156 2.281,0.354 0.313,0.198 10 false *a
*a Hold
V100135

Turn


Using a wrench to hold the hexagonal portion of the No. 2 camshaft, install the bolt.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

NOTICE:
·

Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing exhaust gear assembly.



HINT:

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 13050 32.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

NOTICE:
A378076C03
0.74,1.479 1.021,1.927 1.021,1.927 1.198,1.927 true 1.021,1.917 0.917,1.271 true 1.25,1.823 1.563,1.979 0.313,0.156 10 false *a
*a Identification Mark Stamp


There are different types of camshaft timing gear bolts. Make sure to check the identification mark to determine the tightening torque.

Identification Mark
Item Identification Mark Stamp
Type A A
Type B D


a.
A337613C01
1.292,0.771 2.156,0.771 true 1.26,2.979 1.26,2.479 true 2.208,0.698 2.521,0.854 0.313,0.156 10 false *a 1.208,3 1.521,3.156 0.313,0.156 10 false *b
*a Knock Pin Hole
*b Knock Pin


Align and fit the knock pin of the camshaft with the knock pin hole of the camshaft timing gear assembly.

NOTICE:

Be careful not to damage the contact surface of the camshaft timing gear assembly with the knock pin of the camshaft.



b.
A328695C04
0.333,0.5 1,0.5 true 1.333,0.75 2,0.25 2,0.25 2.167,0.25 true 0.177,0.406 0.49,0.563 0.313,0.156 10 false *1 2.208,0.146 2.521,0.302 0.313,0.156 10 false *c 0.865,1.906 1.177,2.063 0.313,0.156 10 false *e 0.073,0.063 0.385,0.219 0.313,0.156 10 false *a 0.083,1.917 0.396,2.073 0.313,0.156 10 false *b 0.875,0.094 1.188,0.25 0.313,0.156 10 false *d
*1 Camshaft Timing Gear Assembly
*a Incorrect
*b Correct
*c Portion (A) of Camshaft
*d Gap
*e No Gap


Check that there is no gap between the camshaft timing gear assembly and portion (A) of the camshaft shown in the illustration.


c.
A337898

Apply engine oil to the areas of the camshaft timing gear bolt shown in the illustration.


d.

Temporarily install the camshaft timing gear bolt.

HINT:

Make sure that the camshaft timing gear bolt is screwed in by at least 3 threads.



e.
A337596C01
1.792,0.177 2.104,0.333 0.313,0.156 10 false *a
*a Hold
V100135

Turn


Using a wrench to hold the hexagonal portion of the camshaft, tighten the camshaft timing gear bolt.

Torque:
Type A : 120 N*m (1224 kgf*cm, 89 ft.*lbf)
Type B : 95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:
·

Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing gear assembly.



HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 13521 33.INSTALL CRANKSHAFT TIMING SPROCKET

a.
A337609

Install the crankshaft timing sprocket to the crankshaft.


Hide 34.ADD ENGINE OIL

a.
A337902

Add 50 cc (3.1 cu. in.) of engine oil into the oil hole shown in the illustration.

NOTICE:
·

Engine oil must be added if the valve lash adjuster assemblies were removed.

·

Make sure that the low pressure chamber and oil paths of the valve lash adjuster assemblies are full of engine oil.




Hide 13561 35.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.
A337594

Install the No. 1 chain vibration damper with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13506 36.INSTALL CHAIN SUB-ASSEMBLY

a.
A339208N01
1.344,0.229 1.635,0.417 0.292,0.188 10 true 40°

Temporarily install the crankshaft pulley set bolt.


b.

Rotate the crankshaft 40° counterclockwise to position the crankshaft pulley key as shown in the illustration.


c.
A337904C01
0.927,3.219 1.698,4.406 1.698,4.406 2.667,3.26 true 2.875,4.208 2.875,3.688 true 0.958,0.49 1.271,0.646 0.313,0.156 10 false *a 2.427,0.542 2.74,0.698 0.313,0.156 10 false *b 2.833,4.219 3.146,4.375 0.313,0.156 10 false A 1.646,4.417 1.917,4.615 0.271,0.198 10 true *c
*a Approximately 7°
*b Approximately 32°
*c Timing Mark


Check that the timing marks of the camshaft timing exhaust gear assembly and camshaft timing gear assembly are as shown in the illustration.

HINT:

"A" is not a timing mark.



d.

Place the chain sub-assembly onto the camshaft timing exhaust gear assembly, camshaft timing gear assembly and crankshaft timing sprocket.

HINT:
·

Make sure the mark plate of the chain sub-assembly faces away from the engine.

·

It is not necessary to install the chain sub-assembly to the teeth of the gears and sprocket.




e.
A337905C01
2.917,1.198 2.208,1.198 true 2.25,1 2.781,0.281 2.781,0.281 3.031,0.281 true 3.073,0.219 3.385,0.375 0.313,0.156 10 false *a 2.938,1.104 3.26,1.313 0.323,0.208 10 true *b
*a Mark Plate (Orange)
*b Timing Mark


Align the mark plate (orange) of the chain sub-assembly with the timing mark of the camshaft timing exhaust gear assembly and install the chain sub-assembly to the camshaft timing exhaust gear assembly.


f.
A339209C01
0.958,1.188 1.365,1.188 true 0.552,0.615 0.906,0.615 0.906,0.615 1.51,1.156 true 0.719,1.094 0.948,1.302 0.229,0.208 10 true *a 0.385,0.531 0.698,0.688 0.313,0.156 10 false *b
*a Mark Plate (Yellow)
*b Timing Mark


Align the mark plate (yellow) of the chain sub-assembly with the timing mark of the crankshaft timing sprocket and install the chain sub-assembly to the crankshaft timing sprocket.


g.
A339210

Tie a string above the crankshaft timing sprocket so that the chain sub-assembly is secure.


h.
A337906C01
0.802,3.865 1.156,3.865 true 0.75,3.635 0.75,3.281 0.75,3.281 0.885,3.281 true 0.938,3.198 1.125,3.417 0.188,0.219 10 true *a 1.198,3.781 1.427,3.969 0.229,0.188 10 true *b
*a Mark Plate (Orange)
*b Timing Mark


Using a wrench, hold the hexagonal portion of the camshaft and rotate the camshaft counterclockwise to align the timing mark of the camshaft timing gear assembly with the mark plate (orange) of the chain sub-assembly, and install the chain sub-assembly to the camshaft timing gear assembly.

HINT:

Hold the camshaft in place with a wrench until the No. 1 chain tensioner assembly is installed.



i.
A337907

Remove the string above the crankshaft timing sprocket, rotate the crankshaft clockwise, and loosen the chain sub-assembly so that the chain tensioner slipper can be installed.

NOTICE:

Make sure the chain sub-assembly is secure.



Hide 13559 37.INSTALL CHAIN TENSIONER SLIPPER

a.
A337593

Install the chain tensioner slipper with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13540 38.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A337602

Install a new gasket and the No. 1 chain tensioner assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Remove the pin from the stopper plate.


Hide 13566B 39.INSTALL TIMING CHAIN GUIDE

a.
A337592

Install the timing chain guide with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 40.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley set bolt.

A337591C01
1.188,2.823 1.594,2.292 1.594,2.292 1.75,2.292 true 6.281,2.948 5.927,2.229 5.927,2.229 5.74,2.229 true 6.271,3.979 6.271,3.438 false 3.51,3.865 4.198,3.865 true 4.26,3.792 4.573,3.948 0.313,0.156 10 true *1 1.031,0.094 1.344,0.25 0.313,0.156 10 false *a 6.073,0.135 6.385,0.292 0.313,0.156 10 false *b 1.792,2.219 2.104,2.375 0.313,0.156 10 false *c 5.583,2.146 5.896,2.302 0.313,0.156 10 false *c 6.24,4.01 6.396,4.208 0.156,0.198 10 false A
*1 Crankshaft Pulley Key - -
*a Approximately 7° *b Approximately 32°
*c Timing Mark - -



b.

Rotate the crankshaft clockwise and align the crankshaft pulley key as shown in the illustration.


c.

Check that the timing marks on the camshaft timing gear assembly and camshaft timing exhaust gear assembly are as shown in the illustration.

HINT:

"A" is not a timing mark.



Hide 11310 41.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 12315A 42.INSTALL ENGINE MOUNTING BRACKET RH

Hide 11324 43.INSTALL TIMING CHAIN COVER PLATE

Hide 15370 44.INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 12215 46.INSTALL CASE SEPARATOR

a.
A337914C01
2.25,0.5 2.667,1.156 2.667,1.156 3.052,0.5 true 2.604,1.208 2.917,1.365 0.313,0.156 10 false *a
*a O-ring


Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the case separator.

NOTICE:

Make sure to securely fit the O-ring into the groove of the case separator.



c.
A337901

Apply a light coat of engine oil to a new oil separator gasket.


d.

Install the oil separator gasket to the case separator.

NOTICE:

Make sure to securely fit the oil separator gasket into the groove of the case separator.



e.
A337913

Install the case separator to the cylinder head cover case sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11193 47.INSTALL SPARK PLUG TUBE GASKET

a.
A337919C01
0.646,3.125 0.854,3.125 0.854,3.125 1.083,2.635 true 1.115,2.5 1.271,2.073 1.271,2.073 1.469,2.073 true 1.51,2 1.823,2.156 0.313,0.156 10 false *1 0.448,3.083 0.76,3.24 0.313,0.156 10 false *2 0.417,2.458 0.729,2.615 0.313,0.156 10 false *a
*1 Spark Plug Tube Gasket
*2 Cylinder Head Cover Sub-assembly
*a 1.0 mm (0.394 in.) or less


Tap in 4 new spark plug tube gaskets to the cylinder head cover sub-assembly.

NOTICE:
·

Do not allow foreign matter to contact the lip of the spark plug tube gasket.

·

Do not tap in the spark plug tube gasket at an angle.




Hide 11201 48.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A337920C02
1.781,1.302 2,1.708 2,1.708 2.344,1.708 true 0.427,1.51 1.042,1.51 true 0.25,1.438 0.563,1.594 0.313,0.156 10 false *1 2.365,1.625 2.625,1.823 0.26,0.198 10 true *2
*1 Camshaft Bearing Cap Oil Hole Gasket
*2 Gasket


Apply a light coat of engine oil to a new camshaft bearing cap oil hole gasket and gasket.


b.

Install the camshaft bearing cap oil hole gasket to the No. 1 camshaft bearing cap.


c.

Install the gasket to the No. 2 camshaft bearing cap.


d.

Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

NOTICE:

Remove any oil from the contact surface.



e.
A337933C01
1.833,4.375 2.01,4.375 2.01,4.375 2.052,3.719 false 3.188,4.313 3.052,4.313 3.052,4.313 2.938,3.719 false 0.667,3.854 1.313,4.479 1.313,4.479 1.281,3.854 true 0.115,0.698 0.271,0.896 0.156,0.198 10 false A 0.146,1.448 0.302,1.646 0.156,0.198 10 false A 0.656,2.438 0.813,2.635 0.156,0.198 10 false B 2.438,3.083 2.635,3.302 0.198,0.219 10 false B 0.635,0.281 0.792,0.479 0.156,0.198 10 false B 0.927,2.729 1.083,2.927 0.156,0.198 10 false A 1.667,4.302 1.979,4.5 0.313,0.198 10 false *1 3.229,4.24 3.417,4.438 0.188,0.198 10 false *2 0.156,3.021 0.469,3.219 0.313,0.198 10 false *a 1.677,3.021 1.99,3.219 0.313,0.198 10 false *a 0.167,3.406 0.479,3.604 0.313,0.198 10 false *b 1.688,3.406 2,3.604 0.313,0.198 10 false *b 2.281,4.104 2.594,4.302 0.313,0.198 10 false *d 1.365,4.438 1.688,4.615 0.323,0.177 10 false *c 2.625,4.104 2.938,4.302 0.313,0.198 10 false *d 3.073,3.021 3.385,3.219 0.313,0.198 10 false *e
*1 Timing Chain Cover Sub-assembly
*2 Camshaft Housing Sub-assembly
*a 45 mm (1.77 in.)
*b 24 mm (0.945 in.)
*c Seal Packing Diameter: 3.0 mm (0.118 in.)
*d Application Width 5.0 mm (0.197 in.)
*e Seal Packing Diameter: 3.0 to 6.0 mm (0.118 to 0.236 in.)
V100135

Seal Packing


Apply seal packing as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.




f.
A337903C01
0.688,0.438 0.51,0.656 0.51,0.656 0.51,0.906 true 2.406,0.802 2.604,0.802 2.604,0.802 2.938,0.531 true 0.208,0.021 0.365,0.219 0.156,0.198 10 false 9 0.063,1.354 0.219,1.552 0.156,0.198 10 false 8 0.177,1.833 0.333,2.031 0.156,0.198 10 false 7 1.313,1.969 1.469,2.167 0.156,0.198 10 true 6 1.823,1.969 2.208,2.156 0.385,0.188 10 true 5, 19 2.479,1.969 2.76,2.146 0.281,0.177 10 false 18 3.052,1.99 3.333,2.167 0.281,0.177 10 false 17 0.865,0.052 1.146,0.229 0.281,0.177 10 true 10 1.333,0.021 1.615,0.198 0.281,0.177 10 true 11 1.771,0.01 2.26,0.188 0.49,0.177 10 true 4, 12 2.365,0.031 2.646,0.208 0.281,0.177 10 true 13 3.052,0.063 3.333,0.24 0.281,0.177 10 false 14 3.188,0.49 3.417,0.688 0.229,0.198 10 false 15 3.208,1.406 3.427,1.594 0.219,0.188 10 false 16 1.448,0.667 1.865,0.865 0.417,0.198 10 true 2, 21 1.823,1.354 2.177,1.531 0.354,0.177 10 false 20, 1 2.604,1.573 2.958,1.75 0.354,0.177 10 true 3, 22 0.448,0.958 0.625,1.177 0.177,0.219 10 true A 2.26,0.719 2.427,0.969 0.167,0.25 10 true B
V100135

Bolt
V100136

Bolt with Seal Washer


Align the cylinder head cover sub-assembly with the pin (A). Then align the cylinder head cover sub-assembly with the pin (B) and install the cylinder head cover sub-assembly.


g.

Install 3 new seal washers and the 17 bolts, and then tighten the bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Do not start the engine for at least 2 hours after installation.



Hide 13471 49.INSTALL CRANKSHAFT PULLEY

a.
A305738C04
1.313,0.927 0.875,0.875 0.875,0.875 1.198,0.635 true 0.833,0.208 1.146,0.365 0.313,0.156 10 false *a 2.26,1.688 2.573,1.844 0.313,0.156 10 false *b 0.542,0.802 1,1 0.458,0.198 10 false SST
*a Hold
*b Turn


Align the crankshaft pulley key with the key groove of the crankshaft pulley.


b.

Using SST, hold the crankshaft pulley and install the crankshaft pulley set bolt.

SST
09213-54015  
09330-00021  

Torque:
260 N*m (2651 kgf*cm, 192 ft.*lbf)

HINT:

Part number of installation bolt for SST (crankshaft pulley holding tool): 91551-80650 (quantity: 2)



Hide 12211 51.INSTALL NO. 1 VENTILATION CASE

a.
A337934C01
2.375,1.969 2.375,1.615 false 2.313,1.979 2.615,2.156 0.302,0.177 10 false *a
*a Seal Packing


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Diameter:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 1 ventilation case within 3 minutes and tighten the bolts and nuts within 15 minutes of applying seal packing.




b.
A337911C02
1.958,1.146 2.125,1.146 2.125,1.146 2.26,0.896 true 1.271,1.188 1.083,1.188 1.083,1.188 0.896,1.615 true 0.542,0.646 0.698,0.844 0.156,0.198 10 true 9 0.5,1.875 0.823,2.073 0.323,0.198 10 true 1, 8 1.104,0.333 1.427,0.531 0.323,0.198 10 true 10 1.781,0.281 2.104,0.479 0.323,0.198 10 true 11 2.563,0.583 2.979,0.802 0.417,0.219 10 true 2, 12 2.719,1.156 2.885,1.333 0.167,0.177 10 true 3 2.719,1.781 2.927,1.979 0.208,0.198 10 true 4 1.969,1.875 2.177,2.073 0.208,0.198 10 true 5 1.479,1.906 1.688,2.104 0.208,0.198 10 true 6 1.063,1.802 1.25,2.01 0.188,0.208 10 true 7 1.833,1.063 1.99,1.26 0.156,0.198 10 false A 1.313,1.104 1.469,1.302 0.156,0.198 10 false A
V100135

Bolt
V100136

Nut


Install the No. 1 ventilation case with the 8 bolts and 2 nuts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

The bolts (A) are tightened twice.



Hide 12204 52.INSTALL PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Hide 11102A 53.INSTALL CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 11102A 54.INSTALL CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11101J 55.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 12108 56.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.

Install a new gasket to the oil filler cap sub-assembly.


b.

Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly.


Hide 19100P 57.INSTALL SPARK PLUG

Hide 58.INSTALL ENGINE COVER JOINT

a.
A338551

Install the 2 engine cover joints.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 89422 59.INSTALL ENGINE COOLANT TEMPERATURE SENSOR

Hide 83520 60.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 89615 61.INSTALL KNOCK CONTROL SENSOR

Hide 29300 62.INSTALL VACUUM PUMP ASSEMBLY