Home › Engine / Hybrid System › 6AR-FSE (ENGINE MECHANICAL) › CYLINDER HEAD › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072202 6AR-FSE ENGINE MECHANICAL _0351459 CYLINDER HEAD A

6AR-FSE ENGINE MECHANICAL  CYLINDER HEAD  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: The vehicle height changes because of suspension or tire replacement.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft

(for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of knock control sensor

·

Replacement of engine coolant temperature sensor

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump with seal assembly (for high pressure side)

·

Replacement of fuel pressure sensor (fuel delivery pipe sub-assembly) (for high pressure side)


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly Perform the following procedures in the order shown:
1.

Reset Memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)for U761E Initialization
(Click here)for U761E Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
Possible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Impossible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Suspension, tires, etc.*1 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system (Click here)for Initialization
(Click here)for Calibration
Replacement of front bumper assembly Front television camera view adjustment
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

PROCEDURE

Hide 13711 1.REMOVE INTAKE VALVE

a.
A337935N01
1.521,1.115 2.24,1.865 2.24,1.865 1.5,1.865 true 2.302,1.792 2.76,1.99 0.458,0.198 10 true SST

Using SST, compress each compression spring and remove the 8 valve spring retainer locks.

SST
09202-70020  09202-00020  

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the 8 valve spring retainers, 8 compression springs and 8 intake valves from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13715 2.REMOVE EXHAUST VALVE

a.
A337936N01
1.667,1.792 0.667,1.802 0.667,1.802 2.021,1.208 true 0.365,1.729 0.823,1.927 0.458,0.198 10 false SST

Using SST, compress the compression spring and remove the 2 valve spring retainer locks.

SST
09202-70020  09202-00020  


b.

Remove the valve spring retainer, compression spring and exhaust valve from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 3.REMOVE VALVE STEM OIL SEAL

a.
A194958

Using needle-nose pliers, remove the valve stem oil seals.


Hide 13734B 4.REMOVE EXHAUST VALVE SPRING SEAT

a.
A194959

Using compressed air and a Magnet Hand, remove the valve spring seats by blowing air onto them.


Hide 11117E 5.REMOVE NO. 1 STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from a No. 1 straight screw plug or a plug is corroded, replace it.


A337937

a.

Using a 10 mm hexagon wrench, remove the 3 No. 1 straight screw plugs and 3 gaskets.


Hide 11117F 6.REMOVE NO. 2 STRAIGHT SCREW PLUG

NOTICE:

If coolant leaks from the No. 2 straight screw plug or the plug is corroded, replace it.


A194961

a.

Using a 14 mm hexagon wrench, remove the No. 2 straight screw plug and gasket.


Hide 17159 7.REMOVE CYLINDER HEAD STUD BOLT

NOTICE:

If a cylinder head stud bolt is deformed or its threads are damaged, replace it.