Home › Engine / Hybrid System › 6AR-FSE (ENGINE MECHANICAL) › CYLINDER BLOCK › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072202 6AR-FSE ENGINE MECHANICAL _0351460 CYLINDER BLOCK A

6AR-FSE ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: The vehicle height changes because of suspension or tire replacement.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft

(for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of knock control sensor

·

Replacement of engine coolant temperature sensor

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump with seal assembly (for high pressure side)

·

Replacement of fuel pressure sensor (fuel delivery pipe sub-assembly) (for high pressure side)


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of automatic transaxle assembly Perform the following procedures in the order shown:
1.

Reset Memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)for U761E Initialization
(Click here)for U761E Registration
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
Possible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Impossible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Suspension, tires, etc.*1 Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)for Initialization
(Click here)for Calibration
·

Television camera controller initialization

·

Adjust steering angle

·

Rear television camera assembly optical axis (Back camera position setting)


Panoramic view monitor system (Click here)for Initialization
(Click here)for Calibration
Replacement of front bumper assembly Front television camera view adjustment
Front wheel alignment adjustment Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

PROCEDURE

Hide 1.INSPECT CONNECTING ROD THRUST CLEARANCE

a.
A338769

Using a dial indicator, measure the thrust clearance while moving the connecting rod sub-assembly back and forth.

Standard Thrust Clearance:

0.160 to 0.512 mm (0.00630 to 0.0202 in.)


Maximum Thrust Clearance:

0.512 mm (0.0202 in.)


If the thrust clearance is more than the maximum, replace the connecting rod sub-assembly. If necessary, replace the crankshaft.


Hide 2.INSPECT CONNECTING ROD OIL CLEARANCE

a.
A338770C01
0.688,0.854 1.365,0.469 1.365,0.469 1.521,0.469 true 1.552,0.385 1.865,0.583 0.313,0.198 10 false *a
*a Alignment Mark


Check the alignment marks on the connecting rod and connecting rod cap to ensure correct reassembly.


b.
A338771

Remove the 2 connecting rod bolts and connecting rod cap.

HINT:

Keep the connecting rod bearing and connecting rod cap together.



c.

Clean the crank pin and connecting rod bearing.


d.

Check the crank pin and connecting rod bearing for pitting and scratches.

If the crank pin or connecting rod bearing is damaged, replace the connecting rod bearings. If necessary, replace the crankshaft.


e.
A338772C01
0.5,0.49 0.719,0.49 0.719,0.49 1.177,1.052 true 0.323,0.406 0.635,0.604 0.313,0.198 10 false *a
*a Plastigage


Lay a strip of Plastigage on the crank pin.


f.
A338773C01
0.406,0.385 0.656,0.385 0.656,0.385 1.115,0.844 true 0.229,0.302 0.542,0.5 0.313,0.198 10 false *a
*a Front Mark


Check that the front mark of the connecting rod cap is facing in the correct direction, and install the connecting rod cap.


g.
A338771

Apply a light coat of engine oil to the threads and under the heads of the 2 connecting rod bolts.


h.

Install and alternately tighten the 2 connecting rod bolts in several steps.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


i.
A101478C50
2.063,0.76 2.333,0.177 2.333,0.177 2.479,0.177 false 1.146,0.385 1.469,0.594 0.323,0.208 10 false 90° 2.49,0.083 2.698,0.281 0.208,0.198 10 false *a
*a Paint Mark
V100136

Engine Front


Mark the front of each connecting rod bolt with paint.


j.

Tighten the connecting rod bolts by 90° as shown in the illustration.

NOTICE:

Do not turn the crankshaft during the measurement.



k.

Remove the 2 connecting rod bolts and connecting rod cap.

HINT:

Keep the connecting rod bearing and connecting rod cap together.



l.
A338774C01
0.552,0.406 0.792,0.406 0.792,0.406 1.396,0.854 true 1.229,4.177 0.635,3.188 0.635,3.188 1.479,3.188 false 0.646,3.198 1.479,3.49 false 0.396,0.313 0.708,0.51 0.313,0.198 10 false *a 0.427,3.094 0.74,3.292 0.313,0.198 10 false *b
*a Plastigage
*b Number Mark


Measure the Plastigage at its widest point.

Standard Oil Clearance:

0.030 to 0.063 mm (0.00118 to 0.00248 in.)


Maximum Oil Clearance:

0.07 mm (0.00276 in.)


NOTICE:

Remove the Plastigage completely after the measurement.


If the oil clearance is more than the maximum, replace the connecting rod bearings. If necessary, replace the crankshaft.

HINT:

If replacing a connecting rod bearing, select a new one with the same number as marked on the connecting rod cap. There are 3 sizes of standard connecting rod bearings, marked "1", "2" or "3" accordingly.


Standard Crank Pin Diameter:

51.492 to 51.500 mm (2.02724 to 2.02756 in.)


Standard Connecting Rod Big End Inside Diameter:
Mark Specified Condition
1 54.500 to 54.508 mm (2.14567 to 2.14598 in.)
2 54.509 to 54.516 mm (2.14602 to 2.14629 in.)
3 54.517 to 54.524 mm (2.14633 to 2.14661 in.)


Standard Connecting Rod Bearing Center Wall Thickness:
Mark Specified Condition
1 1.486 to 1.490 mm (0.0585 to 0.0587 in.)
2 1.491 to 1.494 mm (0.0587 to 0.0588 in.)
3 1.495 to 1.498 mm (0.0589 to 0.0590 in.)



m.

Perform the inspection for each cylinder.


Hide 3.REMOVE PISTON WITH CONNECTING ROD

a.
A194883C01
1.198,0.948 2.333,0.594 2.333,0.594 2.5,0.594 false 2.573,0.5 2.885,0.698 0.313,0.198 10 false *a
*a Ridge Reamer


Using a ridge reamer, remove all the carbon from the top of the cylinder.


b.

Remove the 8 connecting rod bolts, 4 connecting rod caps and 4 connecting rod bearings.

HINT:

Keep the connecting rod bearing and connecting rod cap together.



c.

Push the 4 pistons, 4 connecting rods and 4 connecting rod bearings out through the top of the cylinder block sub-assembly.

HINT:
·

Keep the connecting rod bearings, connecting rod and connecting rod cap together.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




Hide 13041 4.REMOVE CONNECTING ROD BEARING

a.

Remove the connecting rod bearings from the connecting rods and connecting rod caps.

HINT:

Arrange the removed parts in the correct order.



Hide 5.INSPECT CRANKSHAFT THRUST CLEARANCE

a.
A338775

Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

Standard Thrust Clearance:

0.04 to 0.24 mm (0.00157 to 0.00945 in.)


Maximum Thrust Clearance:

0.30 mm (0.0118 in.)


If the thrust clearance is more than the maximum, replace the crankshaft thrust washers as a set. If necessary, replace the crankshaft.

Standard Thrust Washer Thickness:

1.93 to 1.98 mm (0.0760 to 0.0780 in.)



Hide 13411 6.REMOVE CRANKSHAFT

a.
A338969N02
0.438,0.604 0.594,0.802 0.156,0.198 10 false 4 0.438,1.573 0.594,1.771 0.156,0.198 10 false 3 1.042,1.708 1.198,1.906 0.156,0.198 10 true 7 1.833,1.771 1.99,1.969 0.156,0.198 10 true 9 2.635,1.677 2.802,1.875 0.167,0.198 10 true 5 3.167,1.698 3.396,1.896 0.229,0.198 10 true 1 0.948,0.5 1.073,0.677 0.125,0.177 10 true 8 1.781,0.417 1.99,0.583 0.208,0.167 10 true 10 2.667,0.615 2.792,0.792 0.125,0.177 10 true 6 3.219,0.552 3.344,0.729 0.125,0.177 10 false 2

Uniformly loosen and remove the 10 crankshaft bearing cap bolts in several steps in the order shown in the illustration.


b.

Remove the 5 crankshaft bearing caps from the cylinder block sub-assembly.

HINT:
·

Keep the No. 2 crankshaft bearings and crankshaft bearing caps together.

·

Arrange the removed parts in the correct order.




c.

Remove the crankshaft from the cylinder block sub-assembly.

HINT:

Keep the crankshaft bearings and crankshaft thrust washers together with the cylinder block sub-assembly.



d.

Check each crankshaft journal and crankshaft bearing for pitting and scratches.

If the journal or crankshaft bearing is damaged, replace the crankshaft bearings. If necessary, replace the crankshaft.


Hide 11791 7.REMOVE CRANKSHAFT THRUST WASHER

a.
A337947

Remove the 2 crankshaft thrust washers from the cylinder block sub-assembly.


Hide 11711 8.REMOVE CRANKSHAFT BEARING

a.

Remove the crankshaft bearings and No. 2 crankshaft bearings from the cylinder block sub-assembly and crankshaft bearing caps.

HINT:

Arrange the removed parts in the correct order.



Hide 13471A 9.REMOVE CRANKSHAFT PULLEY KEY

a.

Using a screwdriver, remove the 2 crankshaft pulley keys from the crankshaft.


Hide 13011 10.REMOVE PISTON RING SET

a.
A338784C01
1.948,0.427 2.552,0.427 false 2.594,0.333 2.906,0.531 0.313,0.198 10 false *a
*a Piston Ring Expander


Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring.


b.

Remove the oil ring expander, upper side rail and lower side rail by hand.

HINT:

Arrange the removed parts in the correct order.



Hide 13101A 11.REMOVE PISTON PIN HOLE SNAP RING

a.
A336692C02
1.552,1.896 2.031,1.896 false 1.531,0.198 1.729,0.198 1.729,0.198 1.927,0.865 false 1.354,0.125 1.667,0.281 0.313,0.156 10 false *a 2.083,1.823 2.396,1.979 0.313,0.156 10 false *b
*a Protective Tape
*b Cutout


Using a screwdriver, pry out the piston pin hole snap ring (front side).

NOTICE:
·

Do not remove the piston pin hole snap ring (rear side) unless it has to be replaced.

·

Be careful not to damage the piston when removing the piston pin hole snap ring (front side).



HINT:

Tape the screwdriver tip before use.



Hide 13211 12.REMOVE PISTON

a.
A194886

Gradually heat each piston to 80 to 90°C (176 to 194°F).


b.
A194887

Using a hammer and brass bar, lightly tap out the piston pin. Then remove the connecting rod sub-assembly.

HINT:
·

The piston and piston pin are a matched set.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




Hide 15708 13.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A337948

Using a 5 mm hexagon wrench, remove the 4 bolts and 4 No. 1 oil nozzle sub-assemblies.


Hide 14.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.