Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for 2AR-FE, 6AR-FSE) › 2018.04–2021.02
RM33A0E _52 Drivetrain _065358 DRIVE SHAFT / PROPELLER SHAFT _0319282 FRONT DRIVE SHAFT ASSEMBLY(for 2AR-FE, 6AR-FSE) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 2AR-FE, 6AR-FSE)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43420G 1.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING

a.

Install a new front drive shaft hole snap ring.

NOTICE:

Face the end gap of the front drive shaft hole snap ring downward.



Hide 43420 2.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

a.

Coat the snap ring of the front drive inboard joint assembly with MP grease.


b.

Coat the splines of the front drive inboard joint assembly with Toyota genuine ATF WS.


c.

Coat the lip of the front drive shaft oil seal LH with MP grease.


d.
C370396

Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.

NOTICE:
·

Face the end gap of the front drive shaft hole snap ring downward.

·

Do not damage the front drive shaft oil seal LH.

·

Do not damage the front axle inboard joint boot.

·

Make sure to center the front drive shaft assembly LH during installation to prevent damage to the front drive shaft hole snap ring.



HINT:

Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.



e.
C369733C02
0,0 0,0 false
V100135

Toyota Body Grease W


Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz) of Toyota Body Grease W to each of the 4 areas shown in the illustration.


f.
C370397C01
2.865,0.677 2.25,1.74 2.25,1.74 2.719,0.417 true 2.177,1.75 2.49,1.948 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks and install the front drive shaft assembly LH to the front axle assembly.

NOTICE:
·

Do not damage the front disc brake dust cover.

·

Do not damage the front axle outboard joint boot.

·

Check that there is no foreign matter on the deflector or contact surfaces.

·

Do not push the front axle assembly towards the outside of the vehicle any further than necessary.

·

Do not damage the deflector.




Hide 43410 3.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

a.

Install a new bearing bracket hole snap ring to the front drive shaft assembly RH.


b.

Coat the splines of the front drive inboard joint assembly with Toyota genuine ATF WS.


c.

Coat the lip of the front drive shaft oil seal RH with MP grease.


d.

Align the inboard joint splines, and securely insert the front drive shaft assembly RH.

NOTICE:
·

Do not damage the front drive shaft oil seal RH.

·

Do not damage the front axle inboard joint boot.




e.
C373223

Install the bearing bracket hole snap ring and a new bolt.

Torque:
32.4 N*m (330 kgf*cm, 24 ft.*lbf)


f.
C375487C01
0,0 0,0 false
V100135

Toyota Body Grease W


Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz) of Toyota Body Grease W to each of the 4 areas shown in the illustration.


g.
C370398C01
0.688,0.406 1.125,1.469 1.125,1.469 0.573,0.688 true 1.156,1.5 1.469,1.698 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks and install the front drive shaft assembly RH to the front axle assembly.

NOTICE:
·

Do not damage the front disc brake dust cover.

·

Do not damage the front axle outboard joint boot.

·

Check that there is no foreign matter on the deflector or contact surfaces.

·

Do not push the front axle assembly towards the outside of the vehicle any further than necessary.

·

Do not damage the deflector.




Hide 48069 4.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

Hide 48810 5.INSTALL FRONT STABILIZER LINK ASSEMBLY

Hide 45470 6.CONNECT TIE ROD ASSEMBLY

Hide 89543 7.INSTALL FRONT SPEED SENSOR

Hide 43502H 8.INSTALL FRONT AXLE SHAFT NUT

a.

Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.

NOTICE:
·

Make sure to perform this work even when using a new front drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




b.
C370399

Using a 30 mm deep socket wrench, install the front axle shaft nut.

Torque:
294 N*m (2998 kgf*cm, 217 ft.*lbf)

HINT:

Depress the brake pedal to prevent the drive shaft from rotating.



c.

Using a chisel and hammer, stake the front axle shaft nut.


Hide 11.INSTALL FRONT WHEELS

Hide 12.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 53737B 13.INSTALL FRONT FENDER APRON SEAL LH (for 2AR-FE)

Hide 53737B 14.INSTALL FRONT FENDER APRON SEAL LH (for 6AR-FSE)

Hide 53736 15.INSTALL FRONT FENDER APRON SEAL RH (for 2AR-FE)

Hide 53736 16.INSTALL FRONT FENDER APRON SEAL RH (for 6AR-FSE)