Home › Engine / Hybrid System › 6AR-FSE (ENGINE CONTROL) › SFI SYSTEM › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072203 6AR-FSE ENGINE CONTROL _0351507 SFI SYSTEM C

6AR-FSE ENGINE CONTROL  SFI SYSTEM  P001400  Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1  P001500  Camshaft Position "B" - Timing Over-Retarded Bank 1  


DESCRIPTION

Refer to DTC P001313.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>P001313

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P001400 Camshaft Position "B" - Timing Over-Advanced or System Performance Bank 1 Exhaust valve timing is stuck at a certain value when in the advance range (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing exhaust gear assembly

·

ECM


Comes on DTC stored SAE Code:
P0014
P001500 Camshaft Position "B" - Timing Over-Retarded Bank 1 Exhaust valve timing is stuck at a certain value when in the retard range (1 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing exhaust gear assembly

·

ECM


Comes on DTC stored SAE Code:
P0015

MONITOR DESCRIPTION

The ECM optimizes the exhaust valve timing using the Variable Valve Timing (VVT) system to control the exhaust camshaft. The VVT system includes the ECM, camshaft timing oil control valve assembly and VVT controller (camshaft timing exhaust gear assembly). The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the exhaust camshaft.

If the difference between the target and actual exhaust valve timing is large, and changes in the actual exhaust valve timing are small, the ECM interprets this as the VVT controller stuck malfunction and stores a DTC.

Example:

A DTC P001400 is stored when the following conditions "A" and "B" are met:

(a)

It takes 5 seconds or more to change the valve timing by 5°CA (Condition "A").

(b)

After the above condition is met, the camshaft timing oil control valve assembly (for exhaust camshaft) is forcibly activated for 60 seconds (Condition "B").



A DTC P001500 is stored when the following conditions "C" and "D" are met:

(a)

It takes 5 seconds or more to change the valve timing by 5°CA (Condition "C").

(b)

After the above condition is met, the camshaft timing oil control valve assembly (for exhaust camshaft) is forcibly activated for 10 seconds (Condition "D").



DTC P001400 (Advanced Camshaft Timing) is subject to 2 trip detection logic.

DTC P001500 (Retarded Camshaft Timing) is subject to 1 trip detection logic.

These DTCs indicate that the VVT controller cannot operate properly due to a camshaft timing oil control valve assembly (for exhaust camshaft) malfunction or the presence of foreign matter in the camshaft timing oil control valve assembly (for exhaust camshaft).

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing oil control valve assembly
Camshaft timing exhaust gear assembly
Required Sensors/Components (Related) Camshaft position sensor
Crank position sensor
Engine coolant temperature sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A384199E19
3.708,3.427 3.865,3.427 3.865,3.427 4.135,2.646 false 6.177,3.354 6.333,3.354 6.333,3.354 6.688,2.625 false 2.458,0.063 6.969,0.99 4.51,0.927 10 false *: Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (depress the accelerator pedal by a large amount) and then decelerating the vehicle 10 to 15 times. 0.208,0.469 1.146,0.813 0.938,0.344 10 false Vehicle Speed 0.208,1.094 1.115,1.469 0.906,0.375 10 false Approximately 60 km/h 0.719,2.115 1.427,2.49 0.708,0.375 10 false Idling 0.188,2.365 1.094,2.76 0.906,0.396 10 false Engine Switch on (IG) 1.375,2.354 2.083,2.729 0.708,0.375 10 false [A] 1.615,2.771 2.438,3.115 0.823,0.344 10 false Warming up 2.563,2.781 3.813,3.052 1.25,0.271 10 false 10 minutes or more 2.542,3.333 3.896,3.625 1.354,0.292 10 false 3 minutes or more 1.865,2.042 2.573,2.417 0.708,0.375 10 false [B] 2.99,1.021 3.698,1.396 0.708,0.375 10 false [C] 4.021,2.333 4.729,2.708 0.708,0.375 10 false [D] 4.25,3.167 4.604,3.417 0.354,0.25 10 false [E] 5.458,2.25 5.813,2.5 0.354,0.25 10 false [F]* 6.583,2.323 6.938,2.573 0.354,0.25 10 false [G] 6.823,3.167 7.094,3.417 0.271,0.25 10 false [H] 5.021,3.271 6.375,3.563 1.354,0.292 10 false 3 minutes or more

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Turn the engine switch on (IG) [A].

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

9.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Idle the engine for 3 minutes or more [D].

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P001400 or P001500.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE, perform steps [F] through [H].



16.

Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Depress the accelerator pedal by a large amount.


17.

Idle the engine for 3 minutes or more [G].

18.

Enter the following menus: Powertrain / Engine / Trouble Codes [H].

19.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



20.

Check the DTC judgment result again.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

DTC P001400 or P001500 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. This foreign matter may then be captured by the oil filter.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001400 OR P001500)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P001400 or P001500 is output A
DTC P001400 or P001500 and other DTCs are output B


HINT:

If any DTCs other than P001400 or P001500 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Exhaust VVT OCV Duty Ratio Bank 1.

Powertrain > Engine > Active Test
Tester Display
Control the Exhaust VVT OCV Duty Ratio Bank 1
50004 372 5

e.

Check the engine speed while operating the camshaft timing oil control valve assembly using the GTS.

OK:
GTS Operation Engine Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:

Refer to "Data List / Active Test" [Exhaust VVT OCV Control Duty Ratio Bank 1 and Exhaust VVT Change Angle Bank 1].

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the engine switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400 OR P001500)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400 OR P001500)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001400 or P001500 is output B


HINT:

DTC P001400 or P001500 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. This foreign matter may then be captured by the oil filter.




A

B

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Result:
Proceed to
OK
NG



OK

6.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

6.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)
a.

Remove the cylinder head cover sub-assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY


b.

Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.


c.

Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.

A412761C01
0.906,3.271 1.052,3.271 1.052,3.271 1.396,2.656 true 2.333,3.313 2.479,3.313 2.479,3.313 2.823,2.698 true 4.885,3.281 5.031,3.281 5.031,3.281 5.344,2.833 true 6.094,1.75 5.927,1.75 5.927,1.75 5.427,2.604 true 0.896,0.188 1.208,0.344 0.313,0.156 10 false *a 2.771,0.125 3.083,0.281 0.313,0.156 10 false *b 0.719,3.198 0.896,3.385 0.177,0.188 10 true *c 6.146,1.677 6.458,1.833 0.313,0.156 10 false *d 4.688,3.188 4.885,3.375 0.198,0.188 10 true *e 2.156,3.208 2.333,3.417 0.177,0.208 10 true *c
*a 7.43° *b 32.45°
*c Timing Mark *d "0" Timing Mark
*e Groove - -


HINT:

If the timing marks are not at the positions shown, turn the crankshaft one revolution clockwise.


OK:

Timing marks on camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.


HINT:

If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.



Result:
Proceed to
OK
NG



OK

7.INSPECT OIL CONTROL VALVE FILTER

NG

11.CHECK ENGINE MECHANICAL SYSTEM
7.INSPECT OIL CONTROL VALVE FILTER
A412762C01
1.042,0.74 1.354,0.74 true 1.417,0.667 1.729,0.823 0.313,0.156 10 false *1
*1 Oil Control Valve Filter


a.

b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



Result:
Proceed to
OK
NG



OK

8.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

8.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
a.

Replace the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

9.CLEAR DTC
9.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the engine switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400 OR P001500)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400 OR P001500)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001400 or P001500 is output B




A

END

B

11.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


HINT:

Perform "Inspection After Repair" after repairing or replacing the engine mechanical system.

Click hereEngine / Hybrid System>6AR-FSE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

12.CLEAR DTC

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

12.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the engine switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400 OR P001500)
13.CHECK WHETHER DTC OUTPUT RECURS (DTC P001400 OR P001500)
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine / Trouble Codes.


c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
DTC P001400 or P001500 is output B




A

B