Home › Engine / Hybrid System › 6AR-FSE (ENGINE MECHANICAL) › ENGINE UNIT › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072202 6AR-FSE ENGINE MECHANICAL _0351458 ENGINE UNIT A

6AR-FSE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 29300 1.REMOVE VACUUM PUMP ASSEMBLY

Hide 89615 2.REMOVE KNOCK CONTROL SENSOR

Hide 83520 3.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 89422 4.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 5.REMOVE ENGINE COVER JOINT

a.
A338551

Remove the 2 engine cover joints.


Hide 19100P 6.REMOVE SPARK PLUG

Hide 12108 7.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.

Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.


b.

Remove the gasket from the oil filler cap sub-assembly.


Hide 11101J 8.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 11102A 9.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 10.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 12204 11.REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Hide 12211 12.REMOVE NO. 1 VENTILATION CASE

a.
A337911C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 8 bolts and 2 nuts.


b.
A337912

Remove the No. 1 ventilation case by prying between the No. 1 ventilation case and cylinder block sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and No. 1 ventilation case.


HINT:

Tape the screwdriver tip before use.



Hide 11301K 13.REMOVE CRANKSHAFT POSITION SENSOR

Hide 13471 14.REMOVE CRANKSHAFT PULLEY

a.
A413659C01
1.302,0.906 0.875,0.844 0.875,0.844 1.156,0.583 false 0.563,0.771 1.021,0.969 0.458,0.198 10 false SST 0.469,0.271 0.781,0.469 0.313,0.198 10 false *a 2.344,1.813 2.656,2.01 0.313,0.198 10 false *b
*a Hold
*b Turn


Using SST, hold the crankshaft pulley and loosen the crankshaft pulley set bolt. Further loosen the crankshaft pulley set bolt until 2 or 3 threads are screwed into the crankshaft.

SST
09213-54015  
09330-00021  

HINT:

Part number of installation bolt for SST (crankshaft pulley holding tool): 91551-80650 (quantity: 2)



b.
A413660C01
1.594,1.115 1.813,1.115 false 2.281,0.24 2.385,0.24 2.385,0.24 2.542,0.688 true 1.292,1.031 1.75,1.229 0.458,0.198 10 false SST 2.094,0.135 2.406,0.333 0.313,0.198 10 false *1 0.615,1.927 0.927,2.125 0.313,0.198 10 false *a 1.271,3.198 1.583,3.396 0.313,0.198 10 false *b
*1 Crankshaft Pulley Set Bolt
*a Hold
*b Turn


Using SST and the crankshaft pulley set bolt, remove the crankshaft pulley and crankshaft pulley set bolt.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05011)

HINT:

Apply lubricant to the threads and end of SST.



Hide 11201 15.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A337921C01
0,0 0,0 false
V100135

Bolt
V100136

Bolt with Seal Washer


Remove the 17 bolts, 3 seal washers, cylinder head cover sub-assembly and cylinder head cover gasket.


b.
A337920C03
1.781,1.302 2,1.708 2,1.708 2.344,1.708 true 0.427,1.51 1.042,1.51 true 0.25,1.438 0.563,1.594 0.313,0.156 10 false *1 2.365,1.625 2.625,1.823 0.26,0.198 10 true *2
*1 Camshaft Bearing Cap Oil Hole Gasket
*2 Gasket


Remove the camshaft bearing cap oil hole gasket from the No. 1 camshaft bearing cap.


c.

Remove the gasket from the No. 2 camshaft bearing cap.


Hide 12215 16.REMOVE CASE SEPARATOR

a.
A337913

Remove the 2 bolts and case separator from the cylinder head cover case sub-assembly.


b.
A337901

Remove the oil separator gasket from the case separator.


c.
A337914C01
2.25,0.5 2.667,1.156 2.667,1.156 3.052,0.5 true 2.604,1.208 2.917,1.365 0.313,0.156 10 false *a
*a O-ring


Remove the O-ring from the case separator.


Hide 11193 17.REMOVE SPARK PLUG TUBE GASKET

a.
A337918C01
1.073,1.146 1.573,1.979 1.573,1.979 1.865,1.979 true 1.896,1.906 2.208,2.063 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, pry out the 4 spark plug tube gaskets from the cylinder head cover sub-assembly.

NOTICE:

Be careful not to damage the cylinder head cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 15370 18.REMOVE CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 11324 19.REMOVE TIMING CHAIN COVER PLATE

Hide 12315A 20.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11310 21.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11301C 22.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 23.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley set bolt.

A337591C01
1.188,2.823 1.594,2.292 1.594,2.292 1.75,2.292 true 6.281,2.948 5.927,2.229 5.927,2.229 5.74,2.229 true 6.271,3.979 6.271,3.438 false 3.51,3.865 4.198,3.865 true 4.26,3.792 4.573,3.948 0.313,0.156 10 true *1 1.031,0.094 1.344,0.25 0.313,0.156 10 false *a 6.073,0.135 6.385,0.292 0.313,0.156 10 false *b 1.792,2.219 2.104,2.375 0.313,0.156 10 false *c 5.583,2.146 5.896,2.302 0.313,0.156 10 false *c 6.24,4.01 6.396,4.208 0.156,0.198 10 false A
*1 Crankshaft Pulley Key - -
*a Approximately 7° *b Approximately 32°
*c Timing Mark - -



b.

Rotate the crankshaft clockwise and align the crankshaft pulley key as shown in the illustration.


c.

Check that the timing marks on the camshaft timing exhaust gear assembly and camshaft timing gear assembly are as shown in the illustration.

HINT:

"A" is not a timing mark.



d.

Remove the crankshaft pulley set bolt.


Hide 13566B 24.REMOVE TIMING CHAIN GUIDE

a.
A337592

Remove the bolt and timing chain guide.


Hide 13540 25.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A337600C01
2.052,1.646 2.052,1.188 true 1.135,0.271 1.406,0.271 1.406,0.271 1.771,1 true 0.979,0.167 1.177,0.396 0.198,0.229 10 true *a 2,1.677 2.313,1.833 0.313,0.156 10 true *b
*a Stopper Plate
*b Plunger


Allow the plunger to extend slightly, and then turn the stopper plate counterclockwise to release the lock. Once the lock is released, push the plunger into the No. 1 chain tensioner assembly.


b.
A337601C01
1.375,1.813 2.021,1.813 true 1.188,1.729 1.396,1.969 0.208,0.24 10 true *a
*a Pin


Turn the stopper plate clockwise to set the lock, and insert a pin into the stopper plate hole.


c.
A337602

Remove the 2 bolts, No. 1 chain tensioner assembly and gasket.


Hide 13559 26.REMOVE CHAIN TENSIONER SLIPPER

a.
A337593

Remove the bolt and chain tensioner slipper.


Hide 13506 27.REMOVE CHAIN SUB-ASSEMBLY

a.

Remove the chain sub-assembly.


Hide 13561 28.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A337594

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13521 29.REMOVE CRANKSHAFT TIMING SPROCKET

a.
A337609

Remove the crankshaft timing sprocket from the crankshaft.


Hide 13050 30.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A413661C01
2.083,0.135 2.396,0.333 0.313,0.198 10 false *a
*a Hold
V100135

Turn


Using a wrench to hold the hexagonal portion of the camshaft, remove the camshaft timing gear bolt and camshaft timing gear assembly.

NOTICE:
·

Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing gear assembly.




Hide 13070A 31.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A413662C01
2.167,0.156 2.479,0.354 0.313,0.198 10 false *a
*a Hold
V100135

Turn


Using a wrench to hold the hexagonal portion of the No. 2 camshaft, remove the bolt and camshaft timing exhaust gear assembly.

NOTICE:
·

Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing exhaust gear assembly.




Hide 15707H 32.REMOVE OIL PIPE SUB-ASSEMBLY

a.
A337599

Remove the bolt and oil pipe sub-assembly from the No. 4 camshaft bearing cap.


Hide 11103 33.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A337603N01
2.417,1.958 2.573,2.156 0.156,0.198 10 false 1 2.667,1.958 3.042,2.177 0.375,0.219 10 false 10 0.083,1.677 0.24,1.875 0.156,0.198 10 false 7 0.094,0.927 0.25,1.125 0.156,0.198 10 false 8 0.104,0.438 0.26,0.635 0.156,0.198 10 false 6 1.021,0.052 1.385,0.302 0.365,0.25 10 false 12 0.813,1.958 0.969,2.156 0.156,0.198 10 false 2 1.042,1.958 1.531,2.177 0.49,0.219 10 false 13 0.688,0.604 0.896,0.802 0.208,0.198 10 true 14 1.24,0.604 1.448,0.802 0.208,0.198 10 true 20 1.552,0.042 1.99,0.333 0.438,0.292 10 false 18 2.094,0.031 2.521,0.333 0.427,0.302 10 false 15 2.667,0.031 2.823,0.229 0.156,0.198 10 false 9 3.25,0.865 3.406,1.063 0.156,0.198 10 false 3 3.208,1.271 3.365,1.469 0.156,0.198 10 false 5 3.219,1.771 3.375,1.969 0.156,0.198 10 false 4 2.104,1.958 2.531,2.177 0.427,0.219 10 false 16 1.563,1.958 2.083,2.177 0.521,0.219 10 false 19 1.823,0.635 2.031,0.833 0.208,0.198 10 true 17 2.396,0.635 2.604,0.833 0.208,0.198 10 true 11

Uniformly loosen and remove the 20 bolts in the order shown in the illustration.


b.
A337604

Remove the camshaft housing sub-assembly by prying between the cylinder head sub-assembly and camshaft housing sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 34.REMOVE CAMSHAFT BEARING CAP

a.
A337605N01
0.083,1.729 0.24,1.927 0.156,0.198 10 false 1 0.052,1.021 0.208,1.219 0.156,0.198 10 false 3 0.063,0.323 0.219,0.521 0.156,0.198 10 false 2 0.646,0.958 0.802,1.156 0.156,0.198 10 false 7 1.229,0.927 1.604,1.208 0.375,0.281 10 false 11 1.833,0.979 2.156,1.24 0.323,0.26 10 false 9 2.448,0.979 2.823,1.26 0.375,0.281 10 false 5 2.708,0.135 2.865,0.333 0.156,0.198 10 true 4 2.104,0.135 2.26,0.333 0.156,0.198 10 true 8 1.479,0.125 1.719,0.323 0.24,0.198 10 true 10 0.896,0.135 1.135,0.333 0.24,0.198 10 true 6

Remove the 11 bolts in the order shown in the illustration.


b.

Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.

HINT:

Arrange the removed parts in the correct order.



Hide 13511 35.REMOVE CAMSHAFT

a.

Remove the camshaft from the camshaft housing sub-assembly.


Hide 13512 36.REMOVE NO. 2 CAMSHAFT

a.

Remove the No. 2 camshaft from the camshaft housing sub-assembly.


Hide 15678A 37.REMOVE OIL CONTROL VALVE FILTER

a.
A337607

Remove the oil control valve filter from the No. 1 camshaft bearing cap.


Hide 11811 38.REMOVE NO. 1 CAMSHAFT BEARING

a.
A337608

Remove the No. 1 camshaft bearing from the No. 1 camshaft bearing cap.


Hide 11821 39.REMOVE NO. 2 CAMSHAFT BEARING

a.
A337606

Remove the No. 2 camshaft bearing from the camshaft housing sub-assembly.


Hide 13801 40.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Remove the 16 No. 1 valve rocker arm sub-assemblies.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 41.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.

Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 13716 42.REMOVE VALVE STEM CAP

a.

Remove the 16 valve stem caps from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 43.REMOVE CAMSHAFT HOUSING STUD BOLT

NOTICE:

If a camshaft housing stud bolt is deformed or its threads are damaged, replace it.


Hide 11151A 44.REMOVE CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:

It is not necessary to remove the camshaft bearing cap setting ring pin unless it is being replaced.


Hide 11114A 45.REMOVE CAMSHAFT HOUSING STRAIGHT PIN

NOTICE:

It is not necessary to remove the camshaft housing straight pin unless it is being replaced.


Hide 11101 46.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11445 48.REMOVE CYLINDER BLOCK WATER JACKET SPACER

a.
A336700

Remove the cylinder block water jacket spacer from the cylinder block sub-assembly.

NOTICE:

Be sure to remove the cylinder block water jacket spacer. If it is not removed, it may fall and become damaged when the cylinder block sub-assembly is inverted.



Hide 15620 49.REMOVE OIL FILTER CAP ASSEMBLY

Hide 12101A 50.REMOVE OIL PAN DRAIN PLUG

a.

Remove the oil pan drain plug and gasket from the oil pan sub-assembly.


Hide 12101 51.REMOVE OIL PAN SUB-ASSEMBLY

a.
A337281C01
0.25,0.073 0.656,0.49 0.406,0.417 12 false *A 0.229,2.396 0.625,2.656 0.396,0.26 12 false *B
*A Type A
*B Type B
V100135

Bolt
V100136

Nut


Remove the 11 bolts and 2 nuts.


b.
A118769

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and stiffening crankcase assembly, cut through the applied sealer and remove the oil pan sub-assembly.

NOTICE:
·

Be careful not to damage the stiffening crankcase assembly contact surface of the oil pan sub-assembly.

·

Be careful not to damage the oil pan sub-assembly flange.




Hide 15104 52.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A337922

Remove the 3 bolts, oil strainer sub-assembly and gasket.


Hide 89491 53.REMOVE ENGINE OIL LEVEL SENSOR

Hide 54.REMOVE OIL LEVEL SENSOR BRACKET

a.
A337924

Remove the 2 bolts and oil level sensor bracket from the stiffening crankcase assembly.


Hide 12121 55.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A337925

Remove the clamp from the No. 1 oil pan baffle plate.


b.

Remove the 4 bolts and No. 1 oil pan baffle plate.


Hide 56.INSPECT CRANKSHAFT BACKLASH

a.
A337928

Using a dial indicator, measure the backlash of the crankshaft and balance shaft as shown in the illustration.

Standard Backlash:

0.05 to 0.20 mm (0.00197 to 0.00787 in.)


Maximum Backlash:

0.20 mm (0.00787 in.)


If the backlash is more than the maximum, replace the engine balancer assembly.


Hide 13620B 57.REMOVE ENGINE BALANCER ASSEMBLY

a.
A337927

Remove the 7 bolts and engine balancer assembly from the stiffening crankcase assembly.

NOTICE:

Do not disassemble the engine balancer assembly.



Hide 58.INSPECT NO. 1 BALANCE SHAFT THRUST CLEARANCE

Hide 59.INSPECT NO. 2 BALANCE SHAFT THRUST CLEARANCE

Hide 11420 60.REMOVE STIFFENING CRANKCASE ASSEMBLY

a.
A337929

Remove the 7 bolts.


b.
A337962C01
0.146,0.073 0.458,0.229 0.313,0.156 10 false *a 0.156,2.365 0.469,2.521 0.313,0.156 10 false *b
*a LH Side
*b RH Side


Using a screwdriver, remove the stiffening crankcase assembly by prying between the stiffening crankcase assembly and cylinder block sub-assembly at the places shown in the illustration.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and stiffening crankcase assembly.


HINT:

Tape the screwdriver tip before use.



Hide 15679 61.REMOVE OIL FILTER BRACKET CLIP

a.
A337610

Remove the oil filter bracket clip from the stiffening crankcase assembly.


Hide 62.REMOVE STIFFENING CRANKCASE STUD BOLT

NOTICE:

If a stiffening crankcase stud bolt is deformed or its threads are damaged, replace it.


Hide 63.REMOVE STIFFENING CRANKCASE RING PIN

NOTICE:

It is not necessary to remove the stiffening crankcase ring pin unless it is being replaced.